scholarly journals Simulation and Steady State Analysis of a Non-isolated Diode Rectifier-fed DC-DC Boost Converter with High Static Voltage Gain

2021 ◽  
Vol 7 (03) ◽  
pp. 20-25
Author(s):  
V. Girija and Dr. D. Mural
Keyword(s):  
Steady State ◽  
Output Voltage ◽  
Current Mode ◽  
Open Loop ◽  
Duty Ratio ◽  
Switching Frequency ◽  
Voltage Gain ◽  
Voltage Profile ◽  
Sinusoidal Input ◽  
Bridge Rectifier

This paper presents the simulation and analysis of a non-isolated step-up DC-DC converter operating in continuous inductor current mode with fixed switching frequency. The proposed converter proves better steady state performance in terms of improved voltage gain compared to the conventional boost configuration. The suggested two stage converter topology is fed by an uncontrolled diode bridge rectifier for which the sinusoidal input AC voltage is (50/ 2 ) V (rms). The design of the converter is such that the input AC voltage of (50/ 2 ) V (rms) is stepped up to around 256 V (DC) at the load end for the duty ratio value of 0.8. The performance of the proposed converter configuration is validated through simulation in Matlab/Simulink platform. The open-loop configuration provides higher constant output voltage profile compared to the conventional boost topology. The output voltage and current profiles show reduced settling time with almost no overshoot. The output voltage ripple is reduced to lower value. The suggested configuration ensures that the voltage-current stress across the switches is also reduced.

A Novel Four Switch Infinite Level Inverter

2020 ◽  
Vol 29 (12) ◽  
pp. 2050193 ◽  
Author(s):  
K. T. Ajmal ◽  
K. Muhammedali Shafeeque ◽  
B. Jayanand
Keyword(s):  
Steady State ◽  
Theoretical Analysis ◽  
Output Voltage ◽  
Duty Ratio ◽  
Switching Frequency ◽  
Voltage Level ◽  
Steady State Analysis ◽  
Analysis And Design ◽  
Multilevel Inverters ◽  
Very High

A novel Four Switch Infinite Level Inverter (FSILI) is proposed in this paper. In conventional multilevel inverters, as the number of levels increases the output voltage becomes more sinusoidal. Unlike conventional multilevel topologies, the output voltage level in the proposed topology depends upon the switching frequency. Since the switching frequency is very high, the output voltage level approaches infinity, thus the name Infinite Level Inverter. Proposed topology requires only one inductor and capacitor reducing the size, weight and thus cost of the overall system. Inherent buck operation is happening in the proposed topology with a sine varying duty ratio PWM control. Steady-state analysis and design of the inverter are carried out. The proposed topology is simulated using Matlab/Simulink to evaluate the theoretical analysis and operation. A hardware prototype is also developed to validate the operation of proposed FSILI.

scholarly journals Parallel-charge series-discharge inductor-based voltage boosting technique applied to a rectifier-fed positive output DC-DC converter

2020 ◽  
Vol 18 (5) ◽  
Author(s):  
S. Annapurani ◽  
D. Murali
Keyword(s):  
Output Voltage ◽  
Current Mode ◽  
Input Voltage ◽  
Internal Resistance ◽  
Power Converter ◽  
Duty Ratio ◽  
Voltage Profile ◽  
Voltage Level ◽  
Power Semiconductor ◽  
Boosting Technique

The conventional power electronic boost converters have inherent limitations that they are not able to increase the low DC input voltage level into sufficiently high DC output voltage level. This is because of the fact that (1). the inductor used in the converter has certain amount of internal resistance, and (2). the power devices used in the converter are subjected to high potential stress which led to damage of the devices. A configuration of a non-isolated step-up rectifier-fed positive output power converter capable of converting low DC voltage into high DC output voltage-based on the concept of parallel-charge series-discharge inductors is proposed in this paper. The proposed converter is fed by an uncontrolled diode bridge rectifier to which an input sinusoidal AC voltage of magnitude 30 V (rms) is given. The converter is configured such that the input AC voltage of 30 V (rms) is stepped-up to around 900 V (DC) at the output of the converter, with extremely low duty ratio. The proposed converter configuration employs only two high power semiconductor switches with reduced complexity of control. In this work, the converter topology is presented, and its steady state behavior and dynamic modeling are discussed for continuous inductor current mode operation. Further, it is revealed that the voltage gain of the converter is influenced by the variation of the duty cycle of the power switches. The effectiveness of the converter is better understood through simulation in MATLAB/SIMULINK platform. The results demonstrate that the converter is able to maintain higher constant output voltage profile with significantly reduced overshoot and settling time.     

scholarly journals High Step-up Coupled Inductor Inverters Based on qSBIs

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 3032 ◽  
Author(s):  
Hongchen Liu ◽  
Xi Su ◽  
Junxiong Wang
Keyword(s):  
Steady State ◽  
High Voltage ◽  
Low Voltage ◽  
Duty Ratio ◽  
Voltage Gain ◽  
Passive Components ◽  
Steady State Analysis ◽  
High Voltage Gain ◽  
Voltage Stress ◽  
Working Principle

In this paper, two types of high step-up coupled inductor inverters based on qSBIs (quasi- switched boost inverters) are proposed. By applying the coupled inductor to the qSBIs, the voltage gain of the proposed inverter is regulated by turn ratio and duty ratio. Thus, a high voltage gain can be achieved without the circuits operating at the extreme duty cycle by choosing a suitable turn ratio of the coupled inductor. In addition, the proposed circuits have the characteristics of continuous input current and low voltage stress across the passive components. A boost unit can be added to the proposed inverters for further improvement of the voltage gain. In this paper, the working principle, steady state analysis, and the comparisons of the proposed inverter with other impedance-source inverters are described. A 200 W prototype was created and the experimental results confirm the correctness of the analysis in this paper.

scholarly journals Performance enhancement analysis of an isolated DC-DC converter using fuzzy logic controller

2017 ◽  
Vol 7 (1.2) ◽  
pp. 186 ◽  
Author(s):  
S. Muthu Balaji ◽  
R. Anand ◽  
P. Senthil Pandian
Keyword(s):  
Fuzzy Logic ◽  
High Voltage ◽  
Output Voltage ◽  
Fuzzy Logic Controller ◽  
Performance Enhancement ◽  
Supply Voltage ◽  
Boost Converter ◽  
Open Loop ◽  
Voltage Gain ◽  
Power Application

High voltage gain dc-dc converters plays an major role in many modern industrialized applications like PV and fuel cells, electrical vehicles, dc backup systems (UPS, inverter), HID (high intensity discharge) lamps. As usual boost converter experiences a drawback of obtaining a high voltage at maximum duty cycle. Hence in order to increase the voltage gain of boost converter, this paper discusses about the advanced boost converter using solar power application. By using this technique, boost converter attains a high voltage which is ten times greater than the input supply voltage. The output voltage can be further increased to more than ten times the supply voltage by using a parallel capacitor and a coupled inductor. The voltage stress across the switch can be reduced due to high output voltage. The Converter is initially operated in open loop and then it is connected with closed loop. More over the fuzzy logic controller is used for the ripple reduction.

scholarly journals Dual output DC-DC quasi impedance source converter

2020 ◽  
Vol 10 (4) ◽  
pp. 3988 ◽  
Author(s):  
Muhammad Ado ◽  
Awang Jusoh ◽  
Tole Sutikno ◽  
Mohd Hanipah Muda ◽  
Zeeshan Ahmad Arfeen
Keyword(s):  
Steady State ◽  
Input Voltage ◽  
Boost Converter ◽  
Output Port ◽  
Duty Ratio ◽  
Voltage Gain ◽  
Output Current ◽  
Matlab Simulink ◽  
Four Quadrant

A double output port DC-DC quasi impedance source converter (q-ZSC) is proposed. Each of the outputs has a different voltage gain. One of the outputs is capable of bidirectional (four-quadrant) operation by only varying the duty ratio. The second output has the gain of traditional two-switch buck-boost converter. Operation of the converter was verified by simulating its responses for different input voltages and duty ratios using MATLAB SIMULINK software. Its average steady-state output current and voltage values were determined and used to determine the ripples that existed. These ripples are less than 5% of the average steady-state values for all the input voltage and duty ratio ranges considered.

scholarly journals Study of the operating modes of the high voltage power source for barrier type discharge excitation

Doklady BGUIR ◽  
2021 ◽  
Vol 19 (1) ◽  
pp. 46-51
Author(s):  
A. L. Barakhoev ◽  
O. I. Tikhon ◽  
V. V. Tuboltsev
Keyword(s):  
High Voltage ◽  
Atmospheric Pressure ◽  
Output Voltage ◽  
Current Mode ◽  
Voltage Divider ◽  
Power Source ◽  
Operating Frequency ◽  
Switching Frequency ◽  
Lc Circuit ◽  
Barrier Type

The issues related to the features of operation and modes setting of a high-voltage switching power source based on a sequential autonomous resonant inverter with reverse diodes used to excite an atmospheric pressure barrier type discharge are discussed in the article. It is indicated that the characteristic features of the autonomous resonant inverters operation are the occurrence of damped voltage fluctuations in the LC circuit of the inverter, as well as the dependence of the output alternating voltage on the ratio of the inverter operating frequency (thyristor switching frequency) to the natural resonant frequency of the LC circuit. Depending on this ratio, the inverter can operate in discontinuous, boundary and continuous current mode. The amplitude and shape of the inverter output voltage were controlled using a 1:1000 voltage divider with a C1-65A oscilloscope. The shape of the gate trigger pulses was obtained using a C1-167 oscilloscope. It is established that when the gate trigger pulses are asymmetrical relative to each other due to the operation features of the step-up transformers, the value of the alternating high-voltage at the inverter output is insufficient to excite the atmospheric pressure barrier type discharge. In the case of the gate trigger pulses symmetry, the output voltage of the inverter stage reaches the values required for the breakdown of the dielectric medium. Oscillograms of the inverter output voltage while adjusting its operating frequency are obtained. It is shown that the amplitude value of the voltage at the gas-discharge load increases as the operating frequency of the inverter increases. For the gate trigger pulses frequency of 250 Hz the value of the inverter output voltage amplitude was 3.4 kV, for 460 Hz – 4.0 kV, and for 550 Hz – 4.2 kV.

scholarly journals A High Step-Up Switched Z-Source Converter (HS-SZC) with Minimal Components Count for Enhancing Voltage Gain

Electronics ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 924
Author(s):  
Rahul Kumar ◽  
Ramani Kannan ◽  
Nursyarizal Bin Mohd Nor ◽  
Apel Mahmud
Keyword(s):  
Output Voltage ◽  
Load Capacity ◽  
Renewable Energy Sources ◽  
Experimental Studies ◽  
Cost Effective ◽  
Duty Ratio ◽  
Voltage Gain ◽  
Boost Converters ◽  
Boost Factor ◽  
Output Capacitor

Some applications such as fuel cells or photovoltaic panels offer low output voltage, and it is essential to boost this voltage before connecting to the grid through an inverter. The Z-network converter can be used for the DC-DC conversion to enhance the output voltage of renewable energy sources. However, boosting capabilities of traditional Z-network boost converters are limited, and the utilization of higher parts count makes it bulky and expensive. In this paper, an efficient, high step-up, switched Z-source DC-DC boost converter (HS-SZC) is presented, which offers a higher boost factor at a smaller duty ratio and avoids the instability due to the saturation of inductors. In the proposed converter, the higher voltage gain is achieved by using one inductor and switch at the back end of the conventional Z-source DC-DC converter (ZSC). The idea is to utilize the output capacitor for filtering and charging and discharging loops. Moreover, the proposed converter offers a wider range of load capacity, thus minimizing the power losses and enhancing efficiency. This study simplifies the structure of conventional Z-source converters through the deployment of fewer components, and hence making it more cost-effective and highly efficient, compared to other DC-DC boost converters. Furthermore, a comparison based on the boosting capability and number of components is provided, and the performance of the proposed design is analyzed with non-ideal elements. Finally, simulation and experimental studies are carried out to evaluate and validate the performance of the proposed converter.

scholarly journals Steady State Behavior of a Single-Switch Non-isolated DC-DC SEPIC Converter Topology with Improved Static Voltage Gain

2021 ◽  
Vol 54 (3) ◽  
pp. 445-452
Author(s):  
D. Murali
Keyword(s):  
Steady State ◽  
Output Voltage ◽  
Voltage Gain ◽  
State Behavior ◽  
Dc Voltage ◽  
Voltage Multiplier ◽  
Capacitor Voltage ◽  
Converter Topology ◽  
Steady State Behavior ◽  
Conversion Technology

This paper presents the analysis of steady state behavior of a single switch non-isolated Single Ended Primary Inductance Converter (SEPIC) topology for achieving high DC voltage gain using diode-capacitor voltage multiplier. A voltage boosting module consisting of inductor and capacitor in addition with two diodes is introduced in the conventional SEPIC configuration in order to derive the DC-DC conversion technology proposed in this work. The voltage gain of the converter is extended using a diode-capacitor voltage multiplier cell. The converter suggested in this work has a single controlled switch. Hence, the conduction losses and the control complexity of the switch are very much reduced. The open loop configuration of the proposed non-isolated converter is described under continuous inductor current mode. The voltage boosting capability of the presented converter is compared with that of the existing modified SEPIC structure. The presented positive output converter topology has low switch voltage-current stress compared to the existing modified SEPIC topology given in the literature. The inductor and capacitor components of the suggested converter are so chosen that the DC output voltage and current waveforms show very low percentage of ripples. A DC voltage level of 24 V is given as input to the proposed converter. The DC voltage obtained across the load terminals is around 370 V which is achievable with low duty ratio (= 0.7) of the active switch. The voltage conversion ratio is very much influenced by the variation of the duty cycle of the power switch. In this work, the converter topology is presented and its various modes of operation are explained with equivalent circuits. The PSIM software platform is effectively and efficiently utilized to validate the performance of the converter. The obtained results convey that the proposed DC-DC conversion technology with extended voltage gain has the capability to maintain the steady-state output voltage and current profiles with almost negligible amount of ripples owing to the use of suitably designed non-dissipative elements in LC filter.

scholarly journals Equivalent Two Switches and Single Switch Buck/Buck-Boost Circuits for Solar Energy Harvesting Systems

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 583
Author(s):  
Ehsan Jamshidpour ◽  
Slavisa Jovanovic ◽  
Philippe Poure
Keyword(s):  
Output Voltage ◽  
Experimental Tests ◽  
Buck Converter ◽  
Maximum Power ◽  
Duty Ratio ◽  
Switching Frequency ◽  
Level Control ◽  
Voltage Level ◽  
Synchronous Control ◽  
Solar Energy Harvesting

In this paper, a comparative analysis has been presented of two equivalent circuits of non-isolated buck/buck-boost converters under synchronous control, used in a stand-alone Photovoltaic-battery-load system. The first circuit consists of two cascaded buck and buck-boost classical converters with two controllable switches. The buck converter is used to extract the maximum power of the Photovoltaic source, and the buck-boost converter is applied for the output voltage level control. The second circuit consists of a proposed converter with a single controllable switch. In both cases, the switching frequency is used to track the maximum power point and the duty ratio controls the output voltage level. Selected simulation results and experimental tests confirm that the two conversion circuits have identical behavior under synchronous control. This study shows that the single switch converter has a lower size and cost, but it is limited in the possible control strategy.

Sign in / Sign up

Export Citation Format

Share Document