scholarly journals LAP SHEAR TEST OF A MAGNESIUM FRICTION SPOT JOINT: NUMERIC MODELING

2013 ◽  
Vol 10 (2) ◽  
pp. 97-102 ◽  
Author(s):  
Leonardo Contri Campanelli ◽  
Armando Ítalo Sette Antonialli ◽  
Nelson Guedes de Alcântara ◽  
Claudemiro Bolfarini ◽  
Uceu Fuad Hasan Suhuddin ◽  
...  
Keyword(s):  
Shear Test ◽  
Lap Shear ◽  
Lap Shear Test ◽  
Numeric Modeling

Characterization of FRP-to-concrete bonded interface Description of the single lap shear test

2009 ◽  
Vol 13 (9) ◽  
pp. 1073-1082
Author(s):  
Sylvain Chataigner ◽  
Jean-François Caron ◽  
Karim Benzarti ◽  
Marc Quiertant ◽  
Christophe Aubagnac
Keyword(s):  
Shear Test ◽  
Lap Shear ◽  
Bonded Interface ◽  
Lap Shear Test ◽  
Single Lap Shear Test

Design and development of novel reactive amine nanocontainers for a self-healing epoxy adhesive: self-repairing investigation using the lap shear test

RSC Advances ◽  
2015 ◽  
Vol 5 (27) ◽  
pp. 21023-21032 ◽  
Author(s):  
Sepideh Khoee ◽  
Zahra Kachoei
Keyword(s):  
Fracture Toughness ◽  
Shear Test ◽  
Epoxy Adhesive ◽  
Self Healing ◽  
Design And Development ◽  
Lap Shear ◽  
Lap Shear Test ◽  
P Recovery

Recovery of fracture toughness of a self-healing epoxy adhesive is achieved by using a novel amine nanocontainer.

Mechanical property evaluation of nano‐silver paste sintered joint using lap‐shear test

2012 ◽  
Vol 24 (2) ◽  
pp. 120-126 ◽  
Author(s):  
Xin Li ◽  
Gang Chen ◽  
Xu Chen ◽  
Guo‐Quan Lu ◽  
Lei Wang ◽  
...  
Keyword(s):  
Mechanical Property ◽  
Shear Test ◽  
Silver Paste ◽  
Nano Silver ◽  
Lap Shear ◽  
Property Evaluation ◽  
Lap Shear Test

Use of a single lap shear test to characterize composite-to-concrete or composite-to-steel bonded interfaces

2011 ◽  
Vol 25 (2) ◽  
pp. 468-478 ◽  
Author(s):  
Sylvain Chataigner ◽  
Jean-Francois Caron ◽  
Karim Benzarti ◽  
Marc Quiertant ◽  
Christophe Aubagnac
Keyword(s):  
Shear Test ◽  
Lap Shear ◽  
Lap Shear Test ◽  
Single Lap Shear Test

Joining SiC Ceramics with Ti3SiC2/TixCy Multi-Interlayer by Spark Plasma Sintering

2018 ◽  
Vol 281 ◽  
pp. 343-348 ◽  
Author(s):  
Zhi Quan Wang ◽  
Qiao Liu ◽  
An Kang Yang ◽  
Zhi Hong Zhong
Keyword(s):  
Phase Composition ◽  
Spark Plasma Sintering ◽  
Shear Test ◽  
Energy Dispersive Spectrometer ◽  
Sic Ceramics ◽  
Lap Shear ◽  
Plasma Sintering ◽  
Lap Shear Test ◽  
Spark Plasma ◽  
Short Time

Spark plasma sintering (SPS) is a promising method to obtain robust silicon carbide (SiC) joint at a relatively low temperature within a short time. In this work, the joint of SiC ceramics was prepared with TiH2, Si and C mixture powders by SPS from 1150 to 1450 °C for 10 min. The microstructure of SiC joints was observed by scanning electron microscopy (SEM), and the phase composition of the interlayer was determined by x-ray diffraction (XRD) and energy dispersive spectrometer (EDS). The mechanical properties of SiC joints were evaluated by the single lap shear test. The results showed that the microstructure and phase composition of the joints depended on the joining temperature. A dense joint could be obtained above 1250 °C. Ti3SiC2 and TixCy were found in all joints. Also, the decomposition of Ti3SiC2 occurred in the 1450 °C joint. The highest shear strength of 80.5 ± 7.4 MPa was obtained in the 1350 °C joint. The fracture occurred within the joining interlayer and SiC ceramics during shear test, except for the 1150 °C joint, which existed obvious cavities in the joint.

Sign in / Sign up

Export Citation Format

Share Document