Effect of Metallic Nano-additives on Combustion Performance and Emissions of DI CI Engine Fuelled with Palmkernel Methyl Ester

2017 ◽  
Vol 9 (2) ◽  
Author(s):  
V. Hariram ◽  
S. Seralathan ◽  
M. Rajasekaran ◽  
M. Dinesh Kumar ◽  
S. Padmanabhan
Keyword(s):  
Energy Consumption ◽  
Ignition Delay ◽  
High Speed ◽  
Specific Energy Consumption ◽  
Combustion Efficiency ◽  
Nano Particles ◽  
Experimental Investigations ◽  
Ammonium Bromide ◽  
Compression Ignition ◽  
Compression Ignition Engine

Compression ignition engines are widely used due to their lower energy consumption and enhanced combustion efficiency. In this experimental investigation, the feasibility of fuelling a single cylinder 4 stroke direct injection compression ignition engine with methyl esters of palmkernel (PME) oil along with various fractions of aluminium oxide nano particles (ANOP) were analysed. Two stage transesterification process was adopted to prepare PME. PME20 blend was formulated and fused using high speed homogenizer with varying proportions of AONP as 25 ppm, 50 ppm and 100 ppm in the presence of hexadecyl trimethyl ammonium bromide as surfactant. The experimental investigations were conducted at rated power of 3.5kW at 1500rpm. It was noticed that supplementation of AONP affected the ignition delay significantly favouring enhanced combustion efficiency. The rate of heat release and in-cylinder pressure was substantially increased with notable reduction in ignition delay. Addition of AONP showed an increase in brake thermal efficiency and exhaust gas temperature with diminution in brake specific energy consumption. The unburned hydrocarbons, carbon monoxide and smoke density decreased sharply with an upsurge in NOx. Increase in AONP concentration up-to 100 ppm with PME20 was found to give better combustion and performance characteristics.

scholarly journals An Experimental Investigation on the Effect of Ferrous Ferric Oxide Nano-Additive and Chicken Fat Methyl Ester on Performance and Emission Characteristics of Compression Ignition Engine

Symmetry ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 265
Author(s):  
Ameer Suhel ◽  
Norwazan Abdul Rahim ◽  
Mohd Rosdzimin Abdul Rahman ◽  
Khairol Amali Bin Ahmad ◽  
Yew Heng Teoh ◽  
...  
Keyword(s):  
Methyl Ester ◽  
Ferric Oxide ◽  
Fossil Fuels ◽  
Specific Energy Consumption ◽  
Experimental Results ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
Chicken Fat

In recent years, industries have been investing to develop a potential alternative fuel to substitute the depleting fossil fuels which emit noxious emissions. Present work investigated the effect of ferrous ferric oxide nano-additive on performance and emission parameters of compression ignition engine fuelled with chicken fat methyl ester blends. The nano-additive was included with various methyl ester blends at different ppm of 50, 100, and 150 through the ultrasonication process. Probe sonicator was utilized for nano-fuel preparation to inhibit the formation of agglomeration of nanoparticles in base fuel. Experimental results revealed that the addition of 100 ppm dosage of ferrous ferric oxide nanoparticles in blends significantly improves the combustion performance and substantially decrease the pernicious emissions of the engine. It is also found from an experimental results analysis that brake thermal efficiency (BTE) improved by 4.84%, a reduction in brake specific fuel consumption (BSFC) by 10.44%, brake specific energy consumption (BSEC) by 9.44%, exhaust gas temperature (EGT) by 19.47%, carbon monoxides (CO) by 53.22%, unburned hydrocarbon (UHC) by 21.73%, nitrogen oxides (NOx) by 15.39%, and smoke by 14.73% for the nano-fuel B20FFO100 blend. By seeing of analysis, it is concluded that the doping of ferrous ferric oxide nano-additive in chicken fat methyl ester blends shows an overall development in engine characteristics.

The Compression-Ignition Engine and Its Applicability to British Railway Traction

1933 ◽  
Vol 124 (1) ◽  
pp. 3-61 ◽  
Author(s):  
L. F. R. Fell
Keyword(s):  
Internal Combustion Engine ◽  
High Speed ◽  
Combustion Engine ◽  
Internal Combustion ◽  
High Rate ◽  
Wide Field ◽  
Compression Ignition ◽  
Electric Locomotive ◽  
Compression Ignition Engine ◽  
Railway Traction

The author considers that, while the internal combustion engine is not universally applicable to British railway traction, there is a wide field which can be more economically covered by the oil engine than by other means. Electric transmission is, in spite of high first cost, the most readily adaptable for use in conjunction with the oil engine, and possesses a balance of advantages over all other known systems. The oil-electric locomotive offers a long list of important advantages for railway operation not possessed by other systems. These advantages are, however, offset by high first cost for powers of 1,000 b.h.p. and over. A comparison is drawn between the first cost of steam and oil-electric locomotives for the various duties called for in the service of a British railway. This shows that, while the first cost of the oil-electric main line express passenger locomotive is three times that of the existing steam locomotive, the first costs of branch passenger, medium goods, and shunting steam and oil-electric engines are comparable. This is owing to the cost per brake horse-power required diminishing with increase of size in the case of the steam locomotive, whereas it remains constant in the case of the oil-electric. Owing to the high rate of acceleration necessary the use of the oil-electric system is considered unsuitable as a substitute for dependent electrification of suburban lines. The railway oil engine is a specialized requirement. It must be of the high-speed type running at speeds of up to 1,500 r.p.m., in order to reduce first cost and for other reasons. Details are given of various types of British compression-ignition engines which are considered suitable for British railway work. The author deduces that an engine of twelve-cylinder “V” type and an engine with six cylinders in line, both incorporating the same design and size of cylinder, would fill all the requirements which can be economically met by the oil engine on a British railway. He selects the single sleeve-valve engine design as having the greatest balance of advantages in its favour for railway purposes. Attention is drawn to the importance of simplifying the installation of the compression-ignition engine and various suggestions are put forward to this end. In conclusion the author stresses the importance of the railway companies giving a lead to the internal combustion engine industry as to the railway requirements in size and type of engine, and states that it is the purpose of his paper to assist those concerned in arriving at this immediately important decision.

Ozone-Assisted Combustion—Part I: Literature Review and Kinetic Study Using Detailed n-Heptane Kinetic Mechanism

2014 ◽  
Vol 136 (9) ◽  
Author(s):  
Christopher Depcik ◽  
Michael Mangus ◽  
Colter Ragone
Keyword(s):  
Ignition Delay ◽  
Equivalence Ratio ◽  
Atomic Oxygen ◽  
Direct Injection ◽  
Kinetic Mechanism ◽  
Combustion Model ◽  
Ozone Decomposition ◽  
Compression Ignition ◽  
Review Of The Literature ◽  
Compression Ignition Engine

In this first paper, the authors undertake a review of the literature in the field of ozone-assisted combustion in order to summarize literature findings. The use of a detailed n-heptane combustion model including ozone kinetics helps analyze these earlier results and leads into experimentation within the authors' laboratory using a single-cylinder, direct-injection compression ignition engine, briefly discussed here and in more depth in a following paper. The literature and kinetic modeling outcomes indicate that the addition of ozone leads to a decrease in ignition delay, both in comparison to no added ozone and with a decreasing equivalence ratio. This ignition delay decrease as the mixture leans is counter to the traditional increase in ignition delay with decreasing equivalence ratio. Moreover, the inclusion of ozone results in slightly higher temperatures in the cylinder due to ozone decomposition, augmented production of nitrogen oxides, and reduction in particulate matter through radial atomic oxygen chemistry. Of additional importance, acetylene levels decrease but carbon monoxide emissions are found to both increase and decrease as a function of equivalence ratio. This work illustrates that, beyond a certain level of assistance (approximately 20 ppm for the compression ratio of the authors' engine), adding more ozone has a negligible influence on combustion and emissions. This occurs because the introduction of O3 into the intake causes a temperature-limited equilibrium set of reactions via the atomic oxygen radical produced.

scholarly journals Experimental Research on Controllability and Emissions of Jet-Controlled Compression Ignition Engine

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2936 ◽  
Author(s):  
Hua Tian ◽  
Jingchen Cui ◽  
Tianhao Yang ◽  
Yao Fu ◽  
Jiangping Tian ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
High Speed ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Engine Emissions ◽  
Spark Timing ◽  
Crank Angle ◽  
Marine Engines ◽  
Si Engines ◽  
Ci Engines

Low-temperature combustions (LTCs), such as homogeneous charge compression ignition (HCCI), could achieve high thermal efficiency and low engine emissions by combining the advantages of spark-ignited (SI) engines and compression-ignited (CI) engines. Robust control of the ignition timing, however, still remains a hurdle to practical use. A novel technology of jet-controlled compression ignition (JCCI) was proposed to solve the issue. JCCI combustion phasing was controlled by hot jet formed from pre-chamber spark-ignited combustion. Experiments were done on a modified high-speed marine engine for JCCI characteristics research. The JCCI principle was verified by operating the engine individually in the mode of JCCI and in the mode of no pre-chamber jet under low- and medium-load working conditions. Effects of pre-chamber spark timing and intake charge temperature on JCCI process were tested. It was proven that the combustion phasing of the JCCI engine was closely related to the pre-chamber spark timing. A 20 °C temperature change of intake charge only caused a 2° crank angle change of the start of combustion. Extremely low nitrogen oxides (NOx) emission was achieved by JCCI combustion while keeping high thermal efficiency. The JCCI could be a promising technology for dual-fuel marine engines.

Some Problems Connected with High-Speed Compression-Ignition Engine Development

1932 ◽  
Vol 36 (261) ◽  
pp. 733-787 ◽  
Author(s):  
C. B. Dicksee
Keyword(s):  
High Speed ◽  
Fuel Injection ◽  
Injection System ◽  
Fuel Injection System ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Engine Development

In this paper the author does not propose to deal with any particular form or type of engine or fuel-injection system, but to discuss some of the problems which are encountered when engaged on the development of a high-speed compression-ignition engine.The main problems to be solved consist in devising suitable means for utilising to the fullest possible extent the oxygen available within the cylinder and for avoiding the production of smoke and noise and, in so far as it is connected with combustion conditions, smell.

Preparation of Jatropha Biodiesel Using Hydrotalcite Catalyst and its Performance on Diesel Engine

2011 ◽  
Vol 110-116 ◽  
pp. 1368-1373 ◽  
Author(s):  
Amar P. Pandhare ◽  
S. G. Wagholikar ◽  
R. B. Jadhav Sachin Musale ◽  
A. S. Padalkar
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Specific Energy Consumption ◽  
Exhaust Emissions ◽  
Effect Of Temperature ◽  
Compression Ignition ◽  
Performance Parameters ◽  
Jatropha Oil ◽  
Compression Ignition Engine ◽  
Ci Engines

The heterogeneous catalyst are environment friendly and render the process simplified. A wide variety of solid bases have been examined for this process. The present work reports the use of hydrotalcite catalyst for the synthesis of Biodiesel from jatropha oil. An experimental investigation has been carried out to analyze the performance and emission characteristics of a compression ignition engine fuelled with Jatropha oil and its blends (10%, 20%, 40%, 50%, and 60 % ) with mineral diesel. The effect of temperature on the viscosity of Jatropha oil has also been investigated. A series of engine tests, have been conducted using each of the above fuel blends for comparative performance evaluation. The performance parameters evaluated include thermal efficiency, brake specific fuel consumption (BSFC), brake specific energy consumption (BSEC), and exhaust gas temperature whereas exhaust emissions include mass emissions of CO, HC, NO. These parameters were evaluated in a single cylinder compression ignition diesel engine. The results of the experiment in each case were compared with baseline data of mineral diesel. Significant improvements have been observed in the performance parameters of the engine as well as exhaust emissions. The gaseous emissions of oxide of nitrogen from all blends are lower than mineral diesel at all engine loads. Jatropha oil blends with diesel (up to 50% v/v) can replace diesel for operating the CI engines giving lower emissions and improved engine performance. More over results indicated that B20 have closer performance to diesel and B100 have lower brake thermal efficiency mainly due to its high viscosity compared to diesel.

Combustion system optimization for dimethyl ether using a genetic algorithm

2019 ◽  
Vol 22 (1) ◽  
pp. 22-38 ◽  
Author(s):  
Marius Zubel ◽  
Tamara Ottenwälder ◽  
Benedikt Heuser ◽  
Stefan Pischinger
Keyword(s):  
Oxygen Content ◽  
Dimethyl Ether ◽  
Ignition Delay ◽  
System Optimization ◽  
High Oxygen ◽  
Experimental Investigations ◽  
Compression Ignition Engine ◽  
High Oxygen Content ◽  
Volumetric Heating ◽  
Cooling Effects

Dimethyl ether is a gaseous fuel which can easily be liquefied under moderate pressures. Its high reactivity makes it suitable for combustion in a compression ignition engine, and due to the high oxygen content, its combustion is virtually free of soot. The high oxygen content and low density of dimethyl ether lead to a lower volumetric heating value compared to Diesel fuel. Therefore, the hydraulic flow rates of the injectors have to be increased with larger nozzle holes. The influence of larger nozzle holes on the dimethyl ether spray formation and ignition are presented in this article. Experimental investigations were conducted at a constant-pressure vessel with optical access and with a single-cylinder research engine. Subsequently, a numerical optimization of the piston bowl and injector nozzle has been carried out. A very fast air/fuel mixture formation with dimethyl ether was observed, which leads to a lean combustion with small nozzle diameters. With increasing nozzle diameters, the combustion moves toward stoichiometric conditions and with very large diameters to rich combustion conditions. The ignition delay for small diameters is mostly dominated by the lean mixture, and for large diameters, the ignition delay is strongly influenced by cooling effects. For the optimization, the oxidation potential number was maximized, which proved suitable to simultaneously increase efficiency and reduce emissions. A conventional ω-shaped bowl and a step bowl have been optimized, and large bowl diameters were found to be beneficial for dimethyl ether combustion. Furthermore, nozzle diameters around 150 µm showed the most promising results. Compared to the dimethyl ether reference, the simulations with the optimized ω-shaped bowl showed a power increase of 2.7%. Experimentally, the optimized ω-shaped bowl in combination with the reference injector showed an efficiency increase by more than 1% at 2000 r/min full load compared to the dimethyl ether reference.

Parametric Study of Ignition and Combustion Characteristics From a Gasoline Compression Ignition Engine Using Two Different Reactivity Fuels

2016 ◽  
Author(s):  
Khanh Cung ◽  
Toby Rockstroh ◽  
Stephen Ciatti ◽  
William Cannella ◽  
S. Scott Goldsborough
Keyword(s):  
High Speed ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Injection Timing ◽  
Strong Impact ◽  
Boost Pressure ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Ignition And Combustion

Unlike homogeneous charge compression ignition (HCCI) that has the complexity in controlling the start of combustion event, partially premixed combustion (PPC) provides the flexibility of defining the ignition timing and combustion phasing with respect to the time of injection. In PPC, the stratification of the charge can be influenced by a variety of methods such as number of injections (single or multiple injections), injection pressure, injection timing (early to near TDC injection), intake boost pressure, or combination of several factors. The current study investigates the effect of these factors when testing two gasoline-like fuels of different reactivity (defined by Research Octane Number or RON) in a 1.9-L inline 4-cylinder diesel engine. From the collection of engine data, a full factorial analysis was created in order to identify the factors that most influence the outcomes such as the location of ignition, combustion phasing, combustion stability, and emissions. Furthermore, the interaction effect of combinations of two factors or more was discussed with the implication of fuel reactivity under current operating conditions. The analysis was done at both low (1000 RPM) and high speed (2000 RPM). It was found that the boost pressure and air/fuel ratio have strong impact on ignition and combustion phasing. Finally, injection-timing sweeps were conducted whereby the ignition (CA10) of the two fuels with significantly different reactivity were matched by controlling the boost pressure while maintaining a constant lambda (air/fuel equivalence ratio).

Sign in / Sign up

Export Citation Format

Share Document