Effects of Heat Treatment on the Mechanical and Tribological Properties of Aluminium (LM6) Reinforced with Iron Oxide (Fe2O3)

2020 ◽  
Vol 12 (3) ◽  
Author(s):  
J. Arun Prakash ◽  
P. Shanmughasundaram ◽  
M. Vemburaj ◽  
P. Gowtham
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Iron Oxide ◽  
Treatment Process ◽  
Casting Process ◽  
Stir Casting ◽  
Heat Treatment Process ◽  
Treatment Results ◽  
Mechanical And Tribological Properties

This work deals with the examination of the mechanical properties of Aluminium (LM6) reinforced with iron oxide (Fe2O3). Stir casting process is used to formulate the composite sampling by varying iron oxide in 5% and 10% by weight. Three different heat treatment process of hardening, annealing and normalizing is carried out on samples of aluminium (LM6), aluminium (LM6) + 5% Fe2O3 and aluminium (LM6) + 10% Fe2O3. Composite specimens are tested to analyze the mechanical properties such as hardness, yield stress, tensile strength and elongation. Present reinforcement specks enabled the alloy to preserve higher hardness during the heat treatment. Results have shown substantial improvements in properties of the specimens with various compositions of reinforcement.

Effects of Heat Treatment Process on Mechanical Properties of X70 Grade Pipeline Steel Bends

2015 ◽  
Vol 727-728 ◽  
pp. 322-326 ◽  
Author(s):  
Shi Lu Zhao ◽  
Zhen Zhang ◽  
Lian Chong Qu ◽  
Jun Zhang ◽  
Jian Ming Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Yield Strength ◽  
Thermal Insulation ◽  
Treatment Process ◽  
Pipeline Steel ◽  
Impact Testing ◽  
Air Cooling ◽  
Heat Treatment Process

Effects of heat treatment process of quenching and tempering under different temperature conditions on mechanical properties of X70 grade pipeline steel bends were studied. Brinell hardness, yield strength, tensile strength, elongation and impact absorbing energy of the bends were tested by using hardness tester, cupping machine and impact testing machine, respectively. It shows that the best heat treatment process of the X70 grade pipeline steel bends is quenching at 890 °Cand thermal insulation for 26 min then water cooling followed by tempering at 590 °C and thermal insulation for 60 min then air cooling. Furthermore, the resulting hardness, yield strength, tensile strength, yield ratio, elongation and impact absorbing energy reach HB230, 595 MPa, 725 MPa, 0.82, 28% and 300 J respectively, which has excellent comprehensive mechanical properties.

Effect of Heat Treatment Process on Microstructure and Mechanical Properties of SWRS82B Wire Rod

2010 ◽  
Vol 97-101 ◽  
pp. 752-755 ◽  
Author(s):  
Jia Qi Zhang ◽  
Yi Long Liang ◽  
Song Xiang ◽  
Xiao Di Yang ◽  
Ming Yang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Treatment Process ◽  
Block Size ◽  
Interlamellar Spacing ◽  
Heat Treatment Process ◽  
Austenitizing Temperature ◽  
Isothermal Temperature

The effect of the heat treatment process parameters on the mechanical properties and microstructure of SWRS82B wire rods were investigated. Specimens were austenitized at 850°C~900°C and held at 500°C~600°C. The results show that the interlamellar spacing and the pearlite block size become finer with the decrease of the isothermal temperature. At the same isothermal temperature condition, the interlamellar spacing decreases with the increase of austenitizing temperature. The fine interlamellar spacing increases the yield strength and ultimate tensile strength.

scholarly journals PENGARUH TEMPERATUR ANELING TERHADAP KEKERASAN DAN KEKUATAN PIPA TEMBAGA AC BEKAS

INFO-TEKNIK ◽  
2020 ◽  
Vol 20 (2) ◽  
pp. 193
Author(s):  
R. N. Akhsanu Takwim ◽  
Kris Witono ◽  
Pondi Udianto
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Air Conditioning ◽  
Treatment Process ◽  
Heat Treatment Process ◽  
Test Results ◽  
Proportional Limit ◽  
Limit Stress ◽  
Proportional Limit Stress

During the installation process, copper pipes for air conditioning will experience a very large deformation due to straightening and bending following the installation path. Hardening strains occur that result in changes in mechanical properties in this case decreases ductility making it difficult to do the connecting process with flaring. Studies need to be carried out to restore the mechanical properties of copper pipes that have been used, including the heat treatment process on copper pipes, so that used copper pipes have a better benefit value than having to be recycled. The temperature of the heat treatment is varied from 400oC, 500 oC and 600 oC. Tensile test results show that at annealed temperature of 400 oC has the highest tensile strength of 125.81 N / mm2 and proportional limit stress of 40.52 N / mm2. Whereas in the microhardness test, the highest hardness occurs also at annealed temperature of 400 oC which is equal to 50.8 HV.

PENGARUH HARDENING PADA BAJA JIS G 4051 GRADE S45C TERHADAP SIFAT MEKANIS DAN STRUKTUR MIKRO

2012 ◽  
Vol 11 (2) ◽  
Author(s):  
Koos Sarjono
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Treatment Process ◽  
Engineering Industry ◽  
Heat Treatment Process ◽  
High Quality ◽  
Metallic Material ◽  
Warm Up ◽  
Industrial Demand

Steel represents a metallic material which is still dominantly used in the engineering industry and mechanical construction. In order to fulfil the industrial demand, the high quality and mechanical properties of steel has to be always available.It is necessary to conduct a heat-treatment process to identify the improvement of mechanical properties and microstructure of steel JIS G 4051 grade S 45 C .Results of the heat-treatment process indicate that the maximum tensile strength of the investigated steel is 1074 MPa , it is earning from the warm-up temperature 860 °C and the highest hardness of the investigated steel is 579 HV it is earning from the warm-up temperature 920 °C . These results meet to AISI – SAE 1045 or JIS G 4051 grade S 45 C standard.

scholarly journals Interfacial structure and mechanical properties of the Ta/Re layered composites prepared by chemical vapor deposition

2021 ◽  
Author(s):  
Zhentao Yuan ◽  
Jingchang Chen ◽  
Yan Wei ◽  
Changyi Hu ◽  
Yuan Luo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
High Temperature ◽  
Vapor Deposition ◽  
Treatment Process ◽  
Chemical Vapor ◽  
Layered Composite ◽  
Heat Treatment Process ◽  
Layered Composites

Abstract A novel Ta/Re layered composite with high temperature resistance, low cost, light weight, and excellent mechanical properties has been prepared by chemical vapor deposition, for improving the comprehensive service performance of the aerospace engine nozzle materials. The interface structure, element distribution, and mechanical properties of the Ta/Re layered composites have been studied with scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction, and tensile testing machine. The results show that the structure of the Ta/Re layered composites is flat and smooth, uniform, and dense. Further, the interface joint is a serrated meshing structure, which tremendously improves the interface bonding properties. The high temperature (1600 °C) tensile strength of the heat-treated Ta/Vol. 30% Re layered composite is 125 MPa, which is 2.8 times and 56.3% higher than the commonly used nozzle materials C103 and Nb521, respectively, whereas the raw material cost is only about 46% of that of pure rhenium. The heat treatment process enhances the mutual diffusion behavior of the atoms in the interface diffusion layer, and increases the thickness of the diffusion layer, besides changing the mechanical properties of the material. When the heat treatment process is at 1800 °C × 1 h, the highest tensile strength at room temperature is 739.61 MPa, which is 42.76% higher than that in a deposited state. This work can provide a reference for the further research of the Ta/Re layered composites.

Microstructures and Mechanical Properties of Troostite Nodular Cast Iron by Heat Treatment

2011 ◽  
Vol 480-481 ◽  
pp. 207-210
Author(s):  
Ke Gao Liu ◽  
Ai Min Xu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Cast Iron ◽  
Treatment Process ◽  
Interlamellar Spacing ◽  
Nodular Cast Iron ◽  
Isothermal Treatment ◽  
Heat Treatment Process ◽  
Controlled Cooling

A troostite nodular cast iron was obtained by a heat treatment process of controlled cooling, reheating-up and isothermal treatment. Experimental results show that the troostite substrate demonstrates an interlamellar spacing below 100 nm. The supercooling condition in this specific heat treatment process is key to the formation of troostite. The mechanical properties are excellent, with tensile strength of 905.5~1029.5 MPa, hardness of 30.8~32.8 HRC, and elongation of 3.1~4.0 %.

Microstructures and Mechanical Properties of a New Biomedical Material Mg-13Li-X Alloys

2013 ◽  
Vol 747-748 ◽  
pp. 251-256 ◽  
Author(s):  
Yan Chang Zhang ◽  
Sha Luo ◽  
Qing Qing Zhang ◽  
Xiao Qing Xu ◽  
Tie Tao Zhou
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Treatment Process ◽  
Heat Treatment Process ◽  
Cast State ◽  
Biomedical Material ◽  
Cardiovascular Stents ◽  
Crystal Texture

In this paper, a new biomedical Mg-Li alloy for the improvement of the comprehensive mechanical properties by micro-alloying and processing to meet the need of mechanical properties of biomedical materials. And the Mg-Li (Mg-Li-Al-Zn-Ca-Sr) alloy's processing and heat treatment were investigated in detail. The crystal texture of cast state, forged state and rolled state were observed and analyzed by OM, XRD and SEM. The mechanical properties of every stage were tested as well. The results showed that the grain size was refined obviously by the concentrating of Ca and Sr in the grain boundary. With the increase of rolling lane, the second phase's distribution was changed to a scattered state gradually from the reunion state. The tensile strength of the forged alloy was improved as well as its elongation after cold rolling and with rolled heat treatment process. The tensile strength reached 220MPa and the elongation reach 22%, which might meet the demand of cardiovascular stents mechanics.

Effects of Nano Particles on the Microstructure of LM 25 (A356) Alloy Manufactured by Squeeze Casting

2017 ◽  
Vol 867 ◽  
pp. 64-70
Author(s):  
N. Nagendran ◽  
N. Gayathri ◽  
V.K. Shanmuganathan ◽  
S. Praveen
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Treatment Process ◽  
Squeeze Casting ◽  
Casting Process ◽  
Nano Particles ◽  
Heat Treatment Process ◽  
Cast Part ◽  
Heat Treated ◽  
Squeeze Casting Process

Conventional casting process cannot produce parts as strong as forged parts. Also there are chances of many casting defects such as porosity, hot tears, shrinkage, pin holes, blow holes, mould shift flash, slag, short casting, when casting method is used for fabrication. Thus cast parts only have low mechanical properties. Recent trend is to use Squeeze Casting, which results in superior mechanical and casting properties. This technique is a hybrid metal forming process combining features of both casting and forging in one operation. This process is suitable for low melting alloys like iron and nickel with mechanical properties enhancement. Reduction in micro porosity in cast part and also reduction in machining. Historically, the series of LM were developed for high strength, corrosion resistance, and good machinability for many applications. In this study Squeeze Casting process has been used, since it has porosity free equiaxed grain components of LM 25 composition and cylindrical shaped castings were manufactured successfully by squeeze casting machine at high temperature and high pressure. The first part of the study is about the microstructure of the LM 25 Al-7 Si-0.3 Mg-0.5 Fe alloy. The casting products were made by addition of nano particles and without nano particles. The size of bar casted was by squeeze casting process. It was 260 mm*46mm (7 Pieces). Microstructure of Cast without squeeze and without stirrer, without squeeze and with stirrer, with squeeze and with stirrer Alloys was studied. The second part of the work was the heat treatment process of the finished product. Heat treatment process was conducted at 490○C and for the heat treated metals was quenched at 30○C (water) for the heat treated and unheated metal casting product were taken and microstructure were studied. The results were compared before and after the heat treatment process for addition of nano particles and without nano particles.

Relationship of Microstructure and Mechanical Properties in Er-Containing Aluminum Alloy

2015 ◽  
Vol 1120-1121 ◽  
pp. 1109-1114
Author(s):  
Xin Lei ◽  
Hui Huang ◽  
S.P. Wen
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
Treatment Process ◽  
Mg Alloys ◽  
The Other ◽  
Heat Treatment Process ◽  
Comprehensive Performance ◽  
Relationship Of ◽  
Al Mg Alloys

This study investigated the mechanical properties and microstructures of Er-containing Al–Mg alloys. The research found that the H114-T sheet of Er-containing Al–Mg alloys showed a relative good comprehensive performance in mechanical properties. With the special rolling and heat treatment process, this H114-T sheet showed different morphology of microstructures with the other sheets in Er-containing Al–Mg alloys. Grains in H114-T sheet performed irregular shape polygon, a number of subgrains appeared in grains, the amount of dislocations in grains decreased. H114-T sheet possessed a lot of Copper texture, this may be one of important factors influenced the mechanical properties.

Study of Cu Addition on Precipitation Behaviors and Mechanical Properties in AA6082 Al-Mg-Si Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 825-828 ◽  
Author(s):  
Man Jin ◽  
Jing Li ◽  
Guang Jie Shao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Thermal Stability ◽  
Treatment Process ◽  
Mechanical Tests ◽  
Age Hardening ◽  
Heat Treatment Process ◽  
Softening Process

The precipitation behaviors and microstructures of nano-precipitates in AA6082 Al-Mg-Si alloy with and without Cu additions during heat treatment process were studied using hardness measurements, TEM, mechanical tests and 3DAP. Meanwhile, the softening process of 6082 alloys with Cu and without Cu, isothermally conditioned at 250°C, has also been investigated. It was found that the rate of age hardening, mechanical properties and thermal stability are higher for the Cu-containing alloy. The TEM and 3DAP observations showed that Q’ precipitates were existed after aged at 170°C for 8h in the alloy with Cu addition. Comparing the hardness, mechanical properties and thermal stability curves, it was concluded that the Q’ precipitates play a major role in improving the age hardening kinetics and properties of 6082 alloy with Cu addition.

Sign in / Sign up

Export Citation Format

Share Document