Manufacturing Sequence for Fabrication of High Strength Steel Parts 300m Or 4340 Modified Low-Alloy Steels 270,000 Psi (1860 Mpa) Tensile Strength and Higher

1984 ◽  
Author(s):  
Keyword(s):  
Tensile Strength ◽  
High Strength Steel ◽  
High Strength ◽  
Low Alloy Steels ◽  
Alloy Steels

Low-Alloy High-Strength Steel for Boiler Tubes (LowC-9Cr-2Mo)

1976 ◽  
Vol 98 (2) ◽  
pp. 173-178 ◽  
Author(s):  
T. Yukitoshi ◽  
K. Nishida ◽  
T. Oda ◽  
T. Daikoku
Keyword(s):  
High Temperature ◽  
High Strength Steel ◽  
Austenitic Stainless Steels ◽  
High Strength ◽  
Strengthening Mechanism ◽  
Steel Tube ◽  
High Temperature Strength ◽  
Low Alloy Steels ◽  
Service Test ◽  
Alloy Steels

High-strength steel tube HCM9M (LowC-9Cr-2Mo) steel, which shows the intermediate high-temperature strength between austenitic stainless steels and commercial low-alloy steels, has been developed. It has superior weldability, workability and oxidation resistivity. At present HCM9M tubes have been in-service test as reheater and superheater tubing at the 165,000 kW boiler in Japan without trouble. This report deals with the practical properties of HCM9M steel, service test experience and high temperature strengthening mechanism of the steel from morphological viewpoint of carbide.

scholarly journals STUDYING THE IMPROVEMENT OF TENSILE STRENGTH OF LOW ALLOY HIGH STRENGTH STEEL WELDS USING AN ECONOMICAL TECHNIQUE

2018 ◽  
Vol 18 (3) ◽  
pp. 498-505
Author(s):  
Abdul Sameea J Jilabi
Keyword(s):  
Tensile Strength ◽  
Weld Joint ◽  
Copper Wire ◽  
High Strength Steels ◽  
High Strength ◽  
Low Alloy Steels ◽  
Joint Efficiency ◽  
Comparison Results ◽  
Alloy Steels ◽  
Welding Processes

Low alloy steels are particularly used in manufacturing several parts in the heavyengineering industries, agricultural equipment and dies which may be subject to servicefailure, and thus may need to be repaired by one of the welding processes. The weldabilityof steels is determined by their sensitivity to cracks that can be prevented by the use ofspecial welding procedures which are often expensive and difficult to use. Manual metal arcwelding of low alloy high strength steels was done firstly, using a cheap electrode (OK46.00), followed by the use of an economical technique which depends on coiling copperwires with different diameters around the cheap electrode. The expensive electrode (OK73.68) was also used for comparison. Results showed an increase in the tensile strength (712MPa) and weld joint efficiency (83.8%) when the expensive iron powder low hydrogencovering electrode (OK 73.68) was used. On the other hand, the tensile strength wasdecreased to (206 MPa) and the weld joint efficiency to (24.2%) when the cheap electrode(OK 46.00) was used. Coiling a (0.6 mm) dia. copper wire around the (OK 46.00) electrodeincreased the tensile strength and weld joint efficiency to (510 MPa) and (60%) respectively.

Development of nonmagnetic high-strength steel with the corrosion potential of low-alloy steels

Metallurgist ◽  
1996 ◽  
Vol 40 (5) ◽  
pp. 73-75
Author(s):  
O. A. Bannykh ◽  
V. M. Blinov ◽  
M. V. Kostina
Keyword(s):  
High Strength Steel ◽  
Corrosion Potential ◽  
High Strength ◽  
Low Alloy Steels ◽  
Alloy Steels

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

UNIFLUX V90

Alloy Digest ◽  
1979 ◽  
Vol 28 (2) ◽  
Keyword(s):  
Carbon Dioxide ◽  
High Strength ◽  
Heat Treating ◽  
Carbon Steels ◽  
Low Alloy Steels ◽  
Nickel Steel ◽  
Steel Weld Metal ◽  
Alloy Steels ◽  
Temperature Impact ◽  
Welding Electrode

Abstract UNIFLUX V90 is a continuous flux-cored welding electrode (wire) developed to weld high-strength low-alloy steels, but it may be used to weld other low-alloy steels and carbon steels. It is used to deposit typically 2.40% nickel steel weld metal with good low-temperature impact properties. Welding is protected by a shielding atmosphere of either 75% argon-25% carbon dioxide or 100% carbon dioxide. Uniflux V90 is used widely in shipbuilding and other fabricating industries. It provides around 88,000 psi tensile strength and around 26 food-pounds Charpy V-notch impact at 60 F. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: SA-355. Producer or source: Unicore Inc., United Nuclear Corporation.

CRUCIBLE D6

Alloy Digest ◽  
1962 ◽  
Vol 11 (5) ◽  
Keyword(s):  
Fracture Toughness ◽  
Tensile Strength ◽  
Low Temperature ◽  
High Strength Steel ◽  
High Strength ◽  
Heat Treating ◽  
Steel Company ◽  
Temperature Performance ◽  
Ultra High Strength Steel ◽  
Crucible Steel

Abstract Crucible D6 is a low alloy ultra-high strength steel developed for aircraft-missile applications and primarily designed for use in the 260,000-290,000 psi tensile strength range. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness, creep, and fatigue. It also includes information on low temperature performance as well as forming, heat treating, machining, and joining. Filing Code: SA-129. Producer or source: Crucible Steel Company of America.

TRI-MARK TM-115

Alloy Digest ◽  
1983 ◽  
Vol 32 (8) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Arc Welding ◽  
High Strength ◽  
Heat Treating ◽  
Low Alloy Steels ◽  
Mining Equipment ◽  
Alloy Steels ◽  
Temperature Impact ◽  
Welding Electrode

Abstract TRI-MARK TM-115 is a gas-shielded flux-cored welding electrode for continuous high deposition are welding. It is designed specifically for semiautomatic and automatic arc welding of high-strength low-alloy steels and quenched-and-tempered steels. This gas-sheilded tubular wire can be used for single and multiple-pass welding. It has outstanding low-temperature impact properties. Its applications including mining equipment, large vehicles and similar items. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: SA-392. Producer or source: Tri-Mark Inc..

TRI-MARK TM-811N2

Alloy Digest ◽  
1983 ◽  
Vol 32 (4) ◽  
Keyword(s):  
Low Temperature ◽  
High Strength ◽  
Heat Treating ◽  
Low Alloy Steels ◽  
Nickel Steel ◽  
Fine Grained ◽  
Subzero Temperatures ◽  
Steel Weld Metal ◽  
Alloy Steels ◽  
Welding Electrode

Abstract TRI-MARK TM-811N2 is a flux-cored welding electrode for all position semiautomatic arc welding. It is designed to weld 2-3% nickel steels for applications requiring good toughness at subzero temperatures; in addition, it is used to weld various other high-strength low-alloy steels and various fine-grained steels with low-temperature toughness. Tri-Mark TM-811N2 is used to deposit typically 2.35% nickel steel weld metal with good low-temperature impact properties. It is used for shipbuilding, oil rigs and similar structures. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: SA-389. Producer or source: Tri-Mark Inc..

Sign in / Sign up

Export Citation Format

Share Document