Extrusions, Nickel-Aluminum Bronze, Martensitic, 78.5Cu - 10.5Al - 5.1Ni - 4.8Fe, Solution Heat Treated and Tempered (TQ50)

2006 ◽  
Author(s):  
Keyword(s):  
Aluminum Bronze ◽  
Nickel Aluminum ◽  
Heat Treated ◽  
Nickel Aluminum Bronze

scholarly journals Effect of Fluid Flow on the Corrosion Performance of as-Cast and Heat-Treated Nickel Aluminum Bronze Alloy (UNS C95800) in Saline Solution

2021 ◽  
Vol 2 (1) ◽  
pp. 61-77
Author(s):  
Hamid Reza Jafari ◽  
Ali Davoodi ◽  
Saman Hosseinpour
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Flow Rate ◽  
Solution Temperature ◽  
Aluminum Bronze ◽  
Nickel Aluminum ◽  
Nacl Solution ◽  
Flow Conditions ◽  
Heat Treated ◽  
Nickel Aluminum Bronze

In this work, the corrosion behavior and surface reactivity of as-cast and heat-treated nickel aluminum bronze casting alloy (UNS C95800) in 3.5 wt% NaCl solution is investigated under stagnant and flow conditions. Increasing flow rate conditions are simulated using a rotating disk electrode from 0 to 9000 revolutions per minute (rpm). Optical micrographs confirm the decrease in the phase fraction of corrosion-sensitive β phase in the microstructure of C95800 after annealing, which, in turn, enhances the corrosion resistance of the alloy. Electrochemical studies including open circuit potentiometry, potentiodynamic polarization, and electrochemical impedance spectroscopy are performed to assess the effect of flow rate and heat treatment on the corrosion of samples at 25 and 40 °C in 3.5 wt% NaCl solution. For both as-cast and heat-treated samples, increasing the flow rate (i.e., electrode rotating rate) linearly reduces the corrosion resistance, indicating that the metal dissolution rate is significantly affected by hydrodynamic flow. Increasing the solution temperature negatively impacts the corrosion behavior of the as-cast and heat-treated samples at all flow conditions.

Mechanical Properties at High Temperatures and Microstructures of a Nickel Aluminum Bronze Alloy

2013 ◽  
Vol 683 ◽  
pp. 82-89 ◽  
Author(s):  
Borpit Thossatheppitak ◽  
Surasak Suranuntchai ◽  
Vitoon Uthaisangsuk ◽  
Anchalee Manonukul ◽  
Pinai Mungsuntisuk
Keyword(s):  
Mechanical Properties ◽  
High Temperatures ◽  
Flow Behavior ◽  
Aluminum Bronze ◽  
Nickel Aluminum ◽  
Bronze Alloy ◽  
Heat Treated ◽  
Different Temperatures ◽  
Machine Parts ◽  
Nickel Aluminum Bronze

Nickel Aluminum Bronze (NAB) alloys have been widely used in different kinds of machine parts where the superior resistance to corrosion and erosion in saltwater is needed. In this work, mechanical properties at high temperatures and microstructures of a NAB alloy were investigated. First, NAB specimens were prepared as an as-cast ingot and were subsequently heat-treated at 675°C for 6 hours in order to improve microstructure and mechanical properties. The mechanical properties at high temperatures in form of the plastic flow curves of the NAB alloy were characterized by a deformation dilatometer. The NAB samples were compressed at high temperature and rapidly cooled down to room temperature. The deformation temperatures of 825°C, 850°C and 900°C, a strain rate of 0.01 s-1, and a maximum compression strain of 0.4 were considered. The influences of the temperature on flow behavior of the NAB alloy were investigated. The plastic stress-strain curves at different temperatures were compared with regard to the rate of material strain hardening and softening. It was found that the compression stresses decreased with increasing temperatures. Additionally, the resulted hardness and microstructures of the alloy after forming at high temperatures were analyzed.

scholarly journals Corrosion Behavior of Heat Treated Nickel-Aluminum Bronze Alloy in Artificial Seawater

2011 ◽  
Vol 02 (11) ◽  
pp. 1542-1555 ◽  
Author(s):  
Ashkan Vakilipour Takaloo ◽  
Mohammad Reza Daroonparvar ◽  
Mehdi Mazar Atabaki ◽  
Kamran Mokhtar
Keyword(s):  
Corrosion Behavior ◽  
Artificial Seawater ◽  
Aluminum Bronze ◽  
Nickel Aluminum ◽  
Bronze Alloy ◽  
Heat Treated ◽  
Nickel Aluminum Bronze

Laser freeforming of nickel-aluminum bronze

1999 ◽  
Author(s):  
Kenneth C. Meinert ◽  
Eric J. Whitney
Keyword(s):  
Aluminum Bronze ◽  
Nickel Aluminum ◽  
Nickel Aluminum Bronze

CONCAST AMS 4880-C95510

Alloy Digest ◽  
2019 ◽  
Vol 68 (9) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
Aluminum Bronze ◽  
Nickel Aluminum ◽  
Metal Products ◽  
Nickel Aluminum Bronze ◽  
Bronze Casting

Abstract AMS 4880-C95510 is a nickel-aluminum bronze casting useful for bushings and bearings. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on machining. Filing Code: Cu-895. Producer or source: Concast Metal Products Company.

AUR-O-MET 57

Alloy Digest ◽  
1956 ◽  
Vol 5 (9) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
Tensile Properties ◽  
Abrasion Resistance ◽  
Heat Treating ◽  
Aluminum Bronze ◽  
Nickel Aluminum ◽  
High Nickel ◽  
Nickel Aluminum Bronze

Abstract AUR-O-MET 57 is a high nickel-aluminum bronze that was developed primarily for its abrasion resistance. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on heat treating, machining, and joining. Filing Code: Cu-42. Producer or source: Aurora Metal Company.

Sign in / Sign up

Export Citation Format

Share Document