Improvements of GDI-Injector Optimization Tools for Enhanced SI-Engine Combustion Chamber Layout

1998 ◽  
Author(s):  
M. Pontoppidan ◽  
G. Gaviani ◽  
G. Bella ◽  
V. Rocco
Keyword(s):  
Combustion Chamber ◽  
Si Engine ◽  
Engine Combustion

CFD Study of Heat Transfer in a Spark-Ignition Engine Combustion Chamber

2006 ◽  
Vol 129 (5) ◽  
pp. 609-616 ◽  
Author(s):  
A. R. Noori ◽  
M. Rashidi
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Temporal Variation ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Si Engine ◽  
Engine Combustion

The objective of this study is the thermal investigation of a typical spark-ignition (SI) engine combustion chamber with particular focus in determination of the locations where the heat flux and heat transfer coefficient are highest. This subject is an important key for some design purposes especially thermal loading of the piston and cylinder head. To this end, CFD simulation using the KIVA-3V CFD code on a PC platform for flow, combustion, and heat transfer in a typical SI engine has been performed. Some results including the temporal variation of the area-averaged heat flux and heat transfer coefficient on the piston, combustion chamber, and cylinder wall are presented. Moreover, the temporal variation of the local heat transfer coefficient and heat flux along a centerline on the piston as well as a few locations on the combustion chamber wall are shown. The investigation reveals that during the combustion period, the heat flux and heat transfer coefficient vary substantially in space and time due to the transient nature of the flame propagation. For example, during the early stages of the flame impingement on the wall, the heat flux undergoes a rapid increase by as much as around 10 times the preimpingement level. In other words, the initial rise of the heat flux at any location is related to the time of the flame arrival at that location.

Analysis and Research of the Combustion Process of YN4100QB Diesel Engine

2013 ◽  
Vol 744 ◽  
pp. 35-39
Author(s):  
Lei Ming Shi ◽  
Guang Hui Jia ◽  
Zhi Fei Zhang ◽  
Zhong Ming Xu
Keyword(s):  
Diesel Engine ◽  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Optimization Design ◽  
Combustion Engine ◽  
Geometric Model ◽  
Combustion Process ◽  
Internal Combustion ◽  
Engine Combustion ◽  
Exhaust Noise

In order to obtain the foundation to the research on the Diesel Engine YN4100QB combustion process, exhaust, the optimal design of combustion chamber and the useful information for the design of exhaust muffler, the geometric model and mesh model of a type internal combustion engine are constructed by using FIRE software to analyze the working process of internal combustion engine. Exhaust noise is the main component of automobile noise in the study of controlling vehicle noise. It is primary to design a type of muffler which is good for agricultural automobile engine matching and noise reduction effect. The present car mufflers are all development means. So it is bound to cause the long cycle of product development and waste of resources. Even sometimes not only can it not reach the purpose of reducing the noise but also it leads to reduce the engine dynamic. The strength of the exhaust noise is closely related to engine combustion temperature and pressure. The calculation and initial parameters are applied to the software based on the combustion model and theory. According to the specific operation process of internal combustion engine. Five kinds of common operation condition was compiled. It is obtained for the detailed distribution parameters of combusted gas temperature pressure . It is also got for flow velocity of the fields in cylinder and given for the relation of the parameters and crankshaft angle for the further research. At the same time NOx emissions situation are got. The numerical results show that not only does it provide the 3D distribution data in different crank shaft angle inside the cylinder in the simulation of combustion process, but also it provides a basis for the engine combustion ,emission research, the optimization design of the combustion chamber and the useful information for the designs of muffler.

A Control-Oriented Reaction-Based SI Engine Combustion Model

2018 ◽  
Author(s):  
Ruixue C. Li ◽  
Guoming G. Zhu
Keyword(s):  
Chemical Reaction ◽  
Mass Fraction ◽  
Combustion Process ◽  
Combustion Model ◽  
Spark Ignition Engines ◽  
Si Engine ◽  
Chemical Reaction Mechanism ◽  
Engine Combustion ◽  
Rate Of Heat Release ◽  
Mass And Heat Transfer

This paper proposes a control-oriented chemical reaction-based two-zone combustion model designed to accurately describe the combustion process and thermal performance for spark-ignition engines. The combustion chamber is assumed to be divided into two zones: reaction and unburned zones, where the chemical reaction takes place in the reaction zone and the unburned zone contains all the unburned mixture. In contrast to the empirical pre-determined Wiebe-function-based combustion model, an ideal two-step chemical reaction mechanism is used to reliably model the detailed combustion process such as mass-fraction-burned (MFB) and rate of heat release. The interaction between two zones includes mass and heat transfer at the zone interface to have a smooth combustion process. This control-oriented model is extensively calibrated based on the experimental data to demonstrate its capability of predicting the combustion process and thermodynamic states of the in-cylinder mixture.

scholarly journals Phenomenological model for determining velocity field of LPG jet in combustion chamber of direct injection S.I. engine

2004 ◽  
Vol 26 (2) ◽  
pp. 83-92
Author(s):  
Bui Van Ga ◽  
Phung Xuan Tho ◽  
Nhan Hong Quang ◽  
Nguyen Huu Huong
Keyword(s):  
Combustion Chamber ◽  
Phenomenological Model ◽  
Direct Injection ◽  
Spark Ignition ◽  
Velocity Profiles ◽  
Gas Jet ◽  
Liquefied Petroleum Gas ◽  
Si Engine ◽  
Si Engines ◽  
Stratified Combustion

A phenomenological model has been established to predict the velocity distribution of LPG (Liquefied Petroleum Gas) jet in combustion chamber of spark ignition (SI) engine. A shaped coefficient \(\beta\) governing the similarity of velocity profiles of LPG jets has been defined based on the theoretical and experimental analyses of turbulent diffusion jets. The results show that \(\beta\) is constant for steady jet but it is not the case for unsteady one. The model will enable us to calculate the velocity profiles of LPG jet after ending injection. This is necessary for research of stratified combustion in direct injection LPG SI engines.

Sign in / Sign up

Export Citation Format

Share Document