Transient Spray Characteristics of a Direct-Injection Spark-Ignited Fuel Injector

1997 ◽  
Author(s):  
S. E. Parrish ◽  
P. V. Farrell
Keyword(s):  
Direct Injection ◽  
Fuel Injector ◽  
Spray Characteristics

scholarly journals Impact of gasoline direct injection fuel injector hole geometry on spray characteristics under flash boiling and ambient conditions

Fuel ◽  
2019 ◽  
Vol 241 ◽  
pp. 71-82 ◽  
Author(s):  
Changzhao Jiang ◽  
Matthew C. Parker ◽  
Jerome Helie ◽  
Adrian Spencer ◽  
Colin P. Garner ◽  
...  
Keyword(s):  
Direct Injection ◽  
Gasoline Direct Injection ◽  
Fuel Injector ◽  
Ambient Conditions ◽  
Spray Characteristics ◽  
Hole Geometry ◽  
Flash Boiling

SPRAY CHARACTERISTICS IN A DIRECT-INJECTION DIESEL ENGINE

1996 ◽  
Vol 6 (1) ◽  
pp. 95-109 ◽  
Author(s):  
H. C. Yang ◽  
Hong Sun Ryou ◽  
Y. T. Jeong ◽  
Young Ki Choi
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Spray Characteristics ◽  
Direct Injection Diesel Engine

Characterization of Spray Formed by Diesel-Water Mixture Jet Injected Into an Air Crossflow

2017 ◽  
Author(s):  
Jinkwan Song ◽  
Jong Guen Lee
Keyword(s):  
Diesel Fuel ◽  
Drop Size ◽  
Pure Water ◽  
Fuel Mixture ◽  
Water Mixture ◽  
Fuel Injector ◽  
Spray Characteristics ◽  
Two Fluids ◽  
Mixing Ratios ◽  
Fuel Mixtures

Using a mixture of water and diesel fuel is considered a way to reduce gas emissions including NOx and COx in the gas turbine. This paper presents experimental results on spray characteristics of the water-diesel fuel mixture in an air crossflow. A plain-orifice type injector of 0.508 mm in diameter is employed in the research. Pure water, pure diesel fuel, and water-diesel fuel mixtures with different mixing ratios are used to compare their spray characteristics. In order to observe spray behaviors in different breakup regimes, Weber numbers for water of 30 and 125 are chosen as the operating condition and the corresponding Weber numbers for diesel fuel at the same conditions are 92 and 382, respectively. Momentum flux ratios are 10 and 20. A tee connection and a subsequent static mixer are employed at upstream of fuel injector to mix two liquids. Phase Doppler Particle Analyzer (PDPA) measurement is performed to measure droplet distributions and mean drop size at various mixture ratios, and planar laser induced fluorescence (PLIF) technique with dyeing either diesel or water is used to look into the primary breakup process. PDPA data show that the spray characteristics of water-diesel fuel mixtures such as mean drop size and number density distribution can be predicted from the measured drop size distribution of pure fluids by weighting those quantities by mass fraction of each fluid, indicating that the water and diesel are injected alternately without significant mixing between the two fluids. A short transition of liquid flow from water-to-diesel or diesel-to-water produces small fraction of relatively bigger droplets.

scholarly journals Characterization of a Novel Porous Injector for Multi-Lean Direct Injection (M-LDI) Combustor

2017 ◽  
Author(s):  
Jianing Li ◽  
Umesh Bhayaraju ◽  
San-Mou Jeng
Keyword(s):  
Air Temperature ◽  
Mass Fraction ◽  
Direct Injection ◽  
Flame Temperature ◽  
Gaseous Fuel ◽  
Nox Emissions ◽  
Fuel Injector ◽  
Porous Tube ◽  
Lean Direct Injection ◽  
Air Mixing

A generic novel injector was designed for multi-Lean Direct Injection (M-LDI) combustors. One of the drawbacks of the conventional pressure swirl and prefilming type airblast atomizers is the difficulty of obtaining a uniform symmetric spray under all operating conditions. Micro-channels are needed inside the injector for uniformly distributing the fuel. The problem of non-uniformity is magnified in smaller sized injectors. The non-uniform liquid sheet causes local fuel rich/lean zones leading to higher NOx emissions. To overcome these problems, a novel fuel injector was designed to improve the fuel delivery to the injector by using a porous stainless steel material with 30 μm porosity. The porous tube also acts as a prefilming surface. Liquid and gaseous fuels can be injected through the injector. In the present study, gaseous fuel was injected to investigate injector fuel-air mixing performance. The gaseous fuel was injected through a porous tube between two radial-radial swirling air streams to facilitate fuel-air mixing. The advantage of this injector is that it increases the contact surface area between the fuel-air at the fuel injection point. The increased contact area enhances fuel-air mixing. Fuel-air mixing and combustion studies were carried out for both gaseous and liquid fuel. Flame visualization, and emissions measurements were carried out inside the exit of the combustor. The measurements were carried out at atmospheric conditions under fuel lean conditions. Natural gas was used as a fuel in these experiments. Fuel-air mixing studies were carried out at different equivalence ratios with and without confinement. The mass fraction distributions were measured at different downstream locations from the injector exit. Flame characterization was carried out by chemiluminescence at different equivalence ratios and inlet air temperatures. Symmetry of the flame, flame length and heat release distribution were analyzed from the flame images. The effects of inlet air temperature and combustion flame temperature on emissions was studied. Emissions were corrected to 15% O2 concentration. NOx emissions increase with inlet air temperature and flame temperature. Effect of flame temperature on NOx concentration is more significant than effect of inlet air temperature. Fuel-air mixing profile was used to obtain mass fraction Probability Density Function (pdf). The pdfs were used for simulations in Chemkin Pro. The measured emissions concentrations at the exit of the injector was compared with simulations. In Chemkin model, a network model with several PSRs (perfectly stirred reactor) were utilized, followed by a mixer and a PFR (plug flow reactor). The comparison between the simulations and the experimental results was investigated.

Sign in / Sign up

Export Citation Format

Share Document