Fuel Injection Rate Shaping and Its Effect on Exhaust Emissions in a Direct-Injection Diesel Engine Using a Spool Acceleration Type Injection System

1997 ◽  
Author(s):  
Makoto Ikegami ◽  
Koichiro Nakatani ◽  
Shotaro Tanaka ◽  
Koji Yamane
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Exhaust Emissions ◽  
Injection Rate ◽  
Injection System ◽  
Direct Injection Diesel Engine ◽  
Rate Shaping ◽  
Fuel Injection Rate

A High-Speed Direct Injection Diesel Engine for Passenger Cars

1988 ◽  
Vol 202 (3) ◽  
pp. 171-181 ◽  
Author(s):  
J A Stephenson ◽  
B A Hood
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Passenger Cars ◽  
Medium Speed ◽  
Medium Speed Engine ◽  
Hsdi Diesel Engine ◽  
Wide Speed Range

The paper describes the development of a high-speed direct injection (HSDI) diesel engine suitable for passenger car applications. The evolution from a low emissions medium-speed engine, through a four-cylinder 2.3 litre research engine, into a four-cylinder 2.0 litre production engine is presented. The challenge to the engineer has been to develop the HSDI engine to operate with acceptable noise, emissions, smoke and driveability over the wide speed range (up to 5000 r/min) required for passenger cars. The key element in this task was the optimization of the combustion system and fuel injection equipment. The HSDI is shown to have a significant fuel economy advantage over the prechamber indirect injection (IDI) engine. Future developments of the fuel injection system are described which will further enhance the HSDI engine and provide additional noise and emissions control.

Modelling of Spray–Swirl Interaction in Direct Injection Diesel Engine Combustion Chambers

1985 ◽  
Vol 199 (3) ◽  
pp. 187-198 ◽  
Author(s):  
P S Mehta ◽  
A K Gupta
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Three Dimensional ◽  
Combustion Chambers ◽  
Direct Injection Diesel Engine ◽  
Wide Range ◽  
Engine Combustion ◽  
Computation Scheme ◽  
Good Agreement

A mathematical model for predicting spray–swirl interaction in a direct injection diesel engine combustion chamber is developed using centre-line velocity vector/continuum approach. The model has three-dimensional features in fuel spray motion. The present model responds to the various air swirl, fuel injection and cylinder charge conditions. The predicted results are compared with the analytical and experimental data available from various sources in the two-dimensional case. Very good agreement is achieved over a wide range of data. The three-dimensional predictions are directly possible without any alteration in the computation scheme.

Factors Affecting Performance of Dual Fuel Compression Ignition Engines

2013 ◽  
Vol 388 ◽  
pp. 217-222
Author(s):  
Mohamed Mustafa Ali ◽  
Sabir Mohamed Salih
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Factors Affecting

Compression Ignition Diesel Engine use Diesel as conventional fuel. This has proven to be the most economical source of prime mover in medium and heavy duty loads for both stationary and mobile applications. Performance enhancements have been implemented to optimize fuel consumption and increase thermal efficiency as well as lowering exhaust emissions on these engines. Recently dual fueling of Diesel engines has been found one of the means to achieve these goals. Different types of fuels are tried to displace some of the diesel fuel consumption. This study is made to identify the most favorable conditions for dual fuel mode of operation using Diesel as main fuel and Gasoline as a combustion improver. A single cylinder naturally aspirated air cooled 0.4 liter direct injection diesel engine is used. Diesel is injected by the normal fuel injection system, while Gasoline is carbureted with air using a simple single jet carburetor mounted at the air intake. The engine has been operated at constant speed of 3000 rpm and the load was varied. Different Gasoline to air mixture strengths investigated, and diesel injection timing is also varied. The optimum setting of the engine has been defined which increased the thermal efficiency, reduced the NOx % and HC%.

Sign in / Sign up

Export Citation Format

Share Document