Flow Characteristics in Intake Port of Spark Ignition Engine Investigated by CFD and Transient Gas Temperature Measurement

1996 ◽  
Author(s):  
Wolf Bauer ◽  
John B. Heywood ◽  
Oshin Avanessian ◽  
Derlon Chu
Keyword(s):  
Temperature Measurement ◽  
Flow Characteristics ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Intake Port ◽  
Gas Temperature

Flow characteristics of misfired gas in the exhaust manifold of a spark ignition engine

2000 ◽  
Vol 214 (4) ◽  
pp. 373-381 ◽  
Author(s):  
Y Chung ◽  
H Kim ◽  
S Choi ◽  
C Bae
Keyword(s):  
Analytical Model ◽  
Oxygen Concentration ◽  
Oxygen Sensor ◽  
Flow Characteristics ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Exhaust Manifold ◽  
Cycle Simulation ◽  
Twin Peaks ◽  
Wide Range

Misfiring in spark ignition engines should be avoided, otherwise unburned fuel and oxygen are brought into the catalyst, and subsequent combustion greatly increases the temperature, possibly resulting in immediate damage to the catalyst. As a new concept of misfire detection method, the signal fluctuation of a wide-range oxygen sensor has been introduced to monitor the fluctuation of the oxygen concentration at the exhaust manifold confluence point. The current research aims to develop a tool that is capable of predicting the variation in oxygen concentration at the exhaust manifold confluence point, and to investigate the flow characteristics of the misfired gas in the exhaust manifold under misfiring conditions in a cylinder. The oxygen concentration at the confluence point could be predicted by comparing the gas flowrate from the misfiring cylinder with the total exhaust gas flowrate. The gas flowrates from each of the cylinders were calculated using a one-dimensional engine cycle simulation including a gas dynamic model of the intake and exhaust systems. The variation in oxygen concentration was also determined experimentally using a fast-response hydrocarbon analyser. The trend of the oxygen concentration fluctuation calculated by the analytical model was compared with the experimental results. The analytical model could duplicate the measured trend of the fluctuation of oxygen concentration at the confluence point, which was characterized by twin peaks for one misfiring. The twin peaks are mainly caused by the mixing of the misfired gas with the burned gas from normally operating cylinders. The effects of engine load and speed on the characteristics of the variation in oxygen concentration were also investigated analytically and experimentally.

scholarly journals Comparative Study of the Effective Release Energy, Residual Gas Fraction, and Emission Characteristics with Various Valve Port Diameter-Bore Ratios (VPD/B) of a Four-Stroke Spark Ignition Engine

Energies ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1330 ◽  
Author(s):  
Nguyen Xuan Khoa ◽  
Ocktaeck Lim
Keyword(s):  
Load Condition ◽  
Experimental System ◽  
Optimization Method ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Pressure Increase ◽  
Intake Port ◽  
Exhaust Port ◽  
Residual Gas Fraction ◽  
Residual Gas

In this research, the residual gas, peak firing pressure increase, and effective release energy were completely investigated. To obtain this target, the experimental system is installed with a dynamo system and a simulation model was setup. Through combined experimental and simulation methods, the drawbacks of the hardware optimization method were eliminated. The results of the research show that the valve port diameter-bore ratio (VPD/B) has a significant effect on the residual gas, peak firing pressure increase, and effective release energy of a four-stroke spark ignition engine. In this research, the engine was performed at 3000 rpm and full load condition. Following increased IPD/B ratio of 0.3–0.5. The intake port and exhaust port diameter has a contrary effect on engine volumetric efficiency, the residual gas ratio increase 27.3% with larger intake port and decrease 18.6% with larger exhaust port. The engine will perform optimal thermal efficiency when the trapped residual gas fraction ratio is from 13% to 14%. The maximum effective release energy was 0.45 kJ at 0.4 intake port-bore ratio, and 0.451 kJ at 0.35 exhaust port-bore ratio. The NOx emission increases until achieved a maximum value after that decrease even VPD/B was still increasing. With a VPD/B ratio of 0.35 to 0.4, the engine works without the misfiring.

Post-Combustion In-Cylinder Vaporization During Cranking and Startup in a Port-Fuel–Injected Spark Ignition Engine

2005 ◽  
Vol 128 (2) ◽  
pp. 397-402 ◽  
Author(s):  
Jim S. Cowart
Keyword(s):  
Combustion Chamber ◽  
Liquid Fuel ◽  
Combustion Process ◽  
Spark Ignition ◽  
Liquid Films ◽  
Spark Ignition Engine ◽  
Fuel Vapor ◽  
Intake Port ◽  
Warm Up ◽  
Flame Ionization

During port-fuel–injected (PFI) spark-ignition (SI) engine startup and warm-up fuel accounting continues to be a challenge. Excess fuel must be injected for a near stoichiometric combustion charge. The “extra” fuel that does not contribute to the combustion process may stay in the intake port or as liquid films on the combustion chamber walls. Some of this combustion chamber wall liquid fuel is transported to the engine’s oil sump and some of this liquid fuel escapes combustion and evolves during the expansion and exhaust strokes. Experiments were performed to investigate and quantify this emerging in-cylinder fuel vapor post-combustion cycle by cycle during engine startup. It is believed that this fuel vapor is evaporating from cylinder surfaces and emerging from cylinder crevices. A fast in-cylinder diagnostic, the fast flame ionization detector, was used to measure this behavior. Substantial post-combustion fuel vapor was measured during engine startup. The amount of post-combustion fuel vapor that develops relative to the in-cylinder precombustion fuel charge is on the order of one for cold starting (0 °C) and decreases to ∼13 for hot starting engine cycles. Fuel accounting suggests that the intake port puddle forms quickly, over the first few engine cranking cycles. Analysis suggests that sufficient charge temperature and crevice oxygen exists to at least partially oxidize the majority of this post-combustion fuel vapor such that engine out hydrocarbons are not excessive.

Sign in / Sign up

Export Citation Format

Share Document