Influence of the Inlet Port and Combustion Chamber Configuration on the Lean-Burn Behaviour of a Spark-Ignition Gasoline Engine

1996 ◽  
Author(s):  
M. Kühn ◽  
J. Abthoff ◽  
R. Kemmler ◽  
T. Kaiser
Keyword(s):  
Combustion Chamber ◽  
Gasoline Engine ◽  
Spark Ignition ◽  
Lean Burn ◽  
Inlet Port

Lean-Burn Characteristics of a Heavy-Duty Diesel Engine Retrofitted to Natural Gas Spark Ignition

2018 ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Fuel Injector ◽  
Heavy Duty ◽  
Lean Burn ◽  
Spark Timing ◽  
Heavy Duty Diesel

Increased utilization of natural-gas (NG) in the transportation sector can decrease the use of petroleum-based fuels and reduce greenhouse-gas emissions. Heavy-duty diesel engines retrofitted to NG spark ignition (SI) can achieve higher efficiencies and low NOx, CO, and HC emissions when operated under lean-burn conditions. To investigate the SI lean-burn combustion phenomena in a bowl-in-piston combustion chamber, a conventional heavy-duty direct-injection CI engine was converted to SI operation by replacing the fuel injector with a spark plug and by fumigating NG in the intake manifold. Steady-state engine experiments and numerical simulations were performed at several operating conditions that changed spark timing, engine speed, and mixture equivalence ratio. Results suggested a two-zone NG combustion inside the diesel-like combustion chamber. More frequent and significant late burn (including double-peak heat release rate) was observed for advanced spark timing. This was due to the chamber geometry affecting the local flame speed, which resulted in a faster and thicker flame in the bowl but a slower and thinner flame in the squish volume. Good combustion stability (COVIMEP < 3 %), moderate rate of pressure rise, and lack of knocking showed promise for heavy-duty CI engines converted to NG SI operation.

Lean-Burn Characteristics of a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark Ignition

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin Emil Dumitrescu
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Fuel Injector ◽  
Heavy Duty ◽  
Lean Burn ◽  
Heavy Duty Diesel ◽  
Ci Engines

Increased utilization of natural gas (NG) in the transportation sector can decrease the use of petroleum-based fuels and reduced greenhouse gas emissions. Heavy-duty diesel engines retrofitted to NG spark ignition (SI) can achieve higher efficiencies and low NOX, CO, and hydrocarbon (HC) emissions when operated under lean-burn conditions. To investigate the SI lean-burn combustion phenomena in a bowl-in-piston combustion chamber, a conventional heavy-duty direct-injection CI engine was converted to SI operation by replacing the fuel injector with a spark plug and by fumigating NG in the intake manifold. Steady-state engine experiments and numerical simulations were performed at several operating conditions that changed spark timing (ST), engine speed, and mixture equivalence ratio. Results suggested a two-zone NG combustion inside the diesel-like combustion chamber. More frequent and significant late-burn (including double-peak heat release rate) was observed for advanced ST. This was due to the chamber geometry affecting the local flame speed, which resulted in a faster and thicker flame in the bowl but a slower and thinner flame in the squish volume. Good combustion stability (COVIMEP < 3%), moderate rate of pressure-rise, and lack of knocking showed promise for heavy-duty CI engines converted to NG SI operation.

scholarly journals The Internal Residual Gas and Effective Release Energy of a Spark-Ignition Engine with Various Inlet Port–Bore Ratios and Full Load Condition

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3773
Author(s):  
Nguyen Xuan Khoa ◽  
Ocktaeck Lim
Keyword(s):  
Simulation Model ◽  
Combustion Chamber ◽  
Experimental Model ◽  
Load Condition ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Inlet Port ◽  
Maximum Value ◽  
Residual Gas ◽  
Research Show

This paper presents the effect of inlet port diameter–bore ratios (IPD/B) on the effective release energy and internal exhaust residual gas of a spark-ignition engine. To investigate the exhaust residual gas in the combustion chamber, a simulation model is setup based on AVL-boost software, and to validate the simulation model an experimental model is also setup. The results of the research show that: the IPD/B ratios have a large effect on the residual gas and effective release energy. When the IPD/B ratio increases from 0.3–0.5, the residual gas increases from 0.11% to 0.14%, and the effective release energy increases from 0.33 KJ to a maximum value of 0.45 KJ, and after that decreases. The engine shows the maximum effective release energy at IPD/B ratio is 0.4. The emission of HC and CO is decreased, but the NOx is increased until a maximum value after that decreased.

EXERGY AND EXERGOENVIRONMENTAL ANALYSES OF A SPARK-IGNITION GASOLINE ENGINE

2020 ◽  
Author(s):  
Daniel R. s. Da Silva ◽  
Eduardo José Cidade Cavalcanti ◽  
monica carvalho
Keyword(s):  
Gasoline Engine ◽  
Spark Ignition

Prediction of gaseous pollutant emissions from a spark-ignition direct-injection engine with gas-exchange simulation

2021 ◽  
pp. 146808742110050
Author(s):  
Stefania Esposito ◽  
Lutz Diekhoff ◽  
Stefan Pischinger
Keyword(s):  
Gas Exchange ◽  
Combustion Chamber ◽  
Direct Injection ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Operating Parameters ◽  
Gaseous Pollutant ◽  
Fuel Ratio ◽  
No Emissions

With the further tightening of emission regulations and the introduction of real driving emission tests (RDE), the simulative prediction of emissions is becoming increasingly important for the development of future low-emission internal combustion engines. In this context, gas-exchange simulation can be used as a powerful tool for the evaluation of new design concepts. However, the simplified description of the combustion chamber can make the prediction of complex in-cylinder phenomena like emission formation quite challenging. The present work focuses on the prediction of gaseous pollutants from a spark-ignition (SI) direct injection (DI) engine with 1D–0D gas-exchange simulations. The accuracy of the simulative prediction regarding gaseous pollutant emissions is assessed based on the comparison with measurement data obtained with a research single cylinder engine (SCE). Multiple variations of engine operating parameters – for example, load, speed, air-to-fuel ratio, valve timing – are taken into account to verify the predictivity of the simulation toward changing engine operating conditions. Regarding the unburned hydrocarbon (HC) emissions, phenomenological models are used to estimate the contribution of the piston top-land crevice as well as flame wall-quenching and oil-film fuel adsorption-desorption mechanisms. Regarding CO and NO emissions, multiple approaches to describe the burned zone kinetics in combination with a two-zone 0D combustion chamber model are evaluated. In particular, calculations with reduced reaction kinetics are compared with simplified kinetic descriptions. At engine warm operation, the HC models show an accuracy mainly within 20%. The predictions for the NO emissions follow the trend of the measurements with changing engine operating parameters and all modeled results are mainly within ±20%. Regarding CO emissions, the simplified kinetic models are not capable to predict CO at stoichiometric conditions with errors below 30%. With the usage of a reduced kinetic mechanism, a better prediction capability of CO at stoichiometric air-to-fuel ratio could be achieved.

Sign in / Sign up

Export Citation Format

Share Document