Influence of the Fuel Injection Equipment on NOx Emissions and Particulates on a Large Heavy-Duty Two-Stroke Diesel Engine Operating on Water-in-Fuel Emulsion

1994 ◽  
Author(s):  
Svend Henningsen
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Nox Emissions ◽  
Heavy Duty ◽  
Injection Equipment

A phenomenological combustion analysis of a dual-fuel natural-gas diesel engine

2016 ◽  
Vol 231 (1) ◽  
pp. 66-83 ◽  
Author(s):  
Shuonan Xu ◽  
David Anderson ◽  
Mark Hoffman ◽  
Robert Prucka ◽  
Zoran Filipi
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Heat Release ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Dual Fuel ◽  
Injection Timing ◽  
Heavy Duty ◽  
Engine System ◽  
Wiebe Function

Energy security concerns and an abundant supply of natural gas in the USA provide the impetus for engine designers to consider alternative gaseous fuels in the existing engines. The dual-fuel natural-gas diesel engine concept is attractive because of the minimal design changes, the ability to preserve a high compression ratio of the baseline diesel, and the lack of range anxiety. However, the increased complexity of a dual-fuel engine poses challenges, including the knock limit at a high load, the combustion instability at a low load, and the transient response of an engine with directly injected diesel fuel and port fuel injection of compressed natural gas upstream of the intake manifold. Predictive simulations of the complete engine system are an invaluable tool for investigations of these conditions and development of dual-fuel control strategies. This paper presents the development of a phenomenological combustion model of a heavy-duty dual-fuel engine, aided by insights from experimental data. Heat release analysis is carried out first, using the cylinder pressure data acquired with both diesel-only and dual-fuel (diesel and natural gas) combustion over a wide operating range. A diesel injection timing correlation based on the injector solenoid valve pulse widths is developed, enabling the diesel fuel start of injection to be detected without extra sensors on the fuel injection cam. The experimental heat release trends are obtained with a hybrid triple-Wiebe function for both diesel-only operation and dual-fuel operation. The ignition delay period of dual-fuel operation is examined and estimated with a predictive correlation using the concept of a pseudo-diesel equivalence ratio. A four-stage combustion mechanism is discussed, and it is shown that a triple-Wiebe function has the ability to represent all stages of dual-fuel combustion. This creates a critical building block for modeling a heavy-duty dual-fuel turbocharged engine system.

scholarly journals Understanding elevated real-world NOx emissions: Heavy-duty diesel engine certification testing versus in-use vehicle testing

Fuel ◽  
2022 ◽  
Vol 307 ◽  
pp. 121771
Author(s):  
Yu Jiang ◽  
Yi Tan ◽  
Jiacheng Yang ◽  
Georgios Karavalakis ◽  
Kent C. Johnson ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Real World ◽  
Nox Emissions ◽  
Heavy Duty ◽  
Certification Testing ◽  
Heavy Duty Diesel Engine ◽  
Heavy Duty Diesel ◽  
Vehicle Testing

scholarly journals Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3837 ◽  
Author(s):  
Sam Ki Yoon ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Engine Load ◽  
Fuel Injection Pressure

This experiment investigates the combustion and emissions characteristics of a common rail direct injection (CRDI) diesel engine using various blends of pure diesel fuel and palm biodiesel. Fuel injection pressures of 45 and 65 MPa were investigated under engine loads of 50 and 100 Nm. The fuels studied herein were pure diesel fuel 100 vol.% with 0 vol.% of palm biodiesel (PBD0), pure diesel fuel 80 vol.% blended with 20 vol.% of palm biodiesel (PBD20), and pure diesel fuel 50 vol.% blended with 50 vol.% of palm biodiesel (PBD50). As the fuel injection pressure increased from 45 to 65 MPa under all engine loads, the combustion pressure and heat release rate also increased. The indicated mean effective pressure (IMEP) increased with an increase of the fuel injection pressure. In addition, for 50 Nm of the engine load, an increase to the fuel injection pressure resulted in a reduction of the brake specific fuel consumption (BSFC) by an average of 2.43%. In comparison, for an engine load of 100 Nm, an increase in the fuel injection pressure decreased BSFC by an average of 0.8%. Hydrocarbon (HC) and particulate matter (PM) decreased as fuel pressure increased, independent of the engine load. Increasing fuel injection pressure for 50 Nm engine load using PBD0, PBD20 and PBD50 decreased carbon monoxide (CO) emissions. When the fuel injection pressure was increased from 45 MPa to 65 MPa, oxides of nitrogen (NOx) emissions were increased for both engine loads. For a given fuel injection pressure, NOx emissions increased slightly as the biodiesel content in the fuel blend increased.

Sign in / Sign up

Export Citation Format

Share Document