Experimental Correlations for Heat Release and Mechanical Losses in Turbocharged Diesel Engines

1993 ◽  
Author(s):  
Raffaele Tuccillo ◽  
Luigi Arnone ◽  
Fabio Bozza ◽  
Roberto Nocera ◽  
Adolfo Senatore
Keyword(s):  
Heat Release ◽  
Diesel Engines

An Improved Rate of Heat Release Model for Modern High-Speed Diesel Engines

2017 ◽  
Vol 139 (9) ◽  
Author(s):  
Peter G. Dowell ◽  
Sam Akehurst ◽  
Richard D. Burke
Keyword(s):  
Heat Release ◽  
Diesel Engines ◽  
Engine Speed ◽  
Fuel Injection ◽  
Maximum Pressure ◽  
Injection Model ◽  
Wall Impingement ◽  
Small Set ◽  
Rate Of Heat Release ◽  
Engine System

To meet the increasingly stringent emissions standards, diesel engines need to include more active technologies with their associated control systems. Hardware-in-the-loop (HiL) approaches are becoming popular where the engine system is represented as a real-time capable model to allow development of the controller hardware and software without the need for the real engine system. This paper focusses on the engine model required in such approaches. A number of semi-physical, zero-dimensional combustion modeling techniques are enhanced and combined into a complete model, these include—ignition delay, premixed and diffusion combustion and wall impingement. In addition, a fuel injection model was used to provide fuel injection rate from solenoid energizing signals. The model was parameterized using a small set of experimental data from an engine dynamometer test facility and validated against a complete data set covering the full engine speed and torque range. The model was shown to characterize the rate of heat release (RoHR) well over the engine speed and load range. Critically, the wall impingement model improved R2 value for maximum RoHR from 0.89 to 0.96. This was reflected in the model's ability to match both pilot and main combustion phasing, and peak heat release rates derived from measured data. The model predicted indicated mean effective pressure and maximum pressure with R2 values of 0.99 across the engine map. The worst prediction was for the angle of maximum pressure which had an R2 of 0.74. The results demonstrate the predictive ability of the model, with only a small set of empirical data for training—this is a key advantage over conventional methods. The fuel injection model yielded good results for predicted injection quantity (R2 = 0.99) and enabled the use of the RoHR model without the need for measured rate of injection.

Influence of the Indicator Channel and Indicator Valve on the Heat Release Characteristics of Medium Speed Marine Diesel Engines

2013 ◽  
Vol 588 ◽  
pp. 149-156 ◽  
Author(s):  
Stanisław Polanowski ◽  
Rafał Pawletko ◽  
Kazimierz Witkowski
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Diesel Engines ◽  
Diagnostic Information ◽  
Injection System ◽  
Indicator Diagram ◽  
Medium Speed ◽  
Marine Diesel ◽  
The Impact

Analysis of the indicator diagram is the basis of technical state evaluation of marine diesel engines. The indicator diagram contains a large amount of diagnostic information. A major problem for the diagnostic use of the indicator diagram is the pressure sensor location. Indicator channel and valve may introduce significant distortions in the resulting pressure. The paper presents results of research conducted on the medium speed laboratory engine Al 25/30. Pressure measurement (indication) was made by the sensor placed directly in the cylinder (instead of starting air valve), before the indicator valve (with special Kistler adapter) and on the indicator valve. Distortion of heat release characteristics for the sensor placed on the indicator valve is important, but it is estimated that diagnostic information is not erased. For medium speed engines is to be expected the use of a portable pressure sensors placed on the indicator valve. For this reason, further research is needed to assess the impact of channels and valves on different cylinders. During the research the course of heat release rate q and the heat released Q were determined. The curve of heat release rate q is a full equivalent to fuel injection pressure curve in the fuel pipes. It allows identification of the failure of the injection system. The curve of Q allows such determination and assessment of internal efficiency of the cylinder.

Quasi-Dimensional Diesel Engine Combustion Modeling With Improved Diesel Spray Tip Penetration, Ignition Delay, and Heat Release Submodels

2017 ◽  
Vol 139 (11) ◽  
Author(s):  
Shuonan Xu ◽  
Hirotaka Yamakawa ◽  
Keiya Nishida ◽  
Zoran Filipi
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Diesel Engines ◽  
Ignition Delay ◽  
Air Entrainment ◽  
Oxygen Mixture ◽  
Diesel Spray ◽  
Spray Tip Penetration ◽  
Simulation Tools ◽  
The Impact

Increasingly stringent fuel economy and CO2 emission regulations provide a strong impetus for development of high-efficiency engine technologies. Diesel engines dominate the heavy duty market and significant segments of the global light duty market due to their intrinsically higher thermal efficiency compared to spark-ignited (SI) engine counterparts. Predictive simulation tools can significantly reduce the time and cost associated with optimization of engine injection strategies, and enable investigation over a broad operating space unconstrained by availability of prototype hardware. In comparison with 0D/1D and 3D simulations, Quasi-Dimensional (quasi-D) models offer a balance between predictiveness and computational effort, thus making them very suitable for enhancing the fidelity of engine system simulation tools. A most widely used approach for diesel engine applications is a multizone spray and combustion model pioneered by Hiroyasu and his group. It divides diesel spray into packets and tracks fuel evaporation, air entrainment, gas properties, and ignition delay (induction time) individually during the injection and combustion event. However, original submodels are not well suited for modern diesel engines, and the main objective of this work is to develop a multizonal simulation capable of capturing the impact of high-injection pressures and exhaust gas recirculation (EGR). In particular, a new spray tip penetration submodel is developed based on measurements obtained in a high-pressure, high-temperature constant volume combustion vessel for pressures as high as 1450 bar. Next, ignition delay correlation is modified to capture the effect of reduced oxygen concentration in engines with EGR, and an algorithm considering the chemical reaction rate of hydrocarbon–oxygen mixture improves prediction of the heat release rates. Spray and combustion predictions were validated with experiments on a single-cylinder diesel engine with common rail fuel injection, charge boosting, and EGR.

Bayesian estimate of pre-mixed and diffusive rate of heat release phases in marine diesel engines

2016 ◽  
Vol 39 (5) ◽  
pp. 1835-1844 ◽  
Author(s):  
Marcelo A. Pasqualette ◽  
Diego C. Estumano ◽  
Fabiana C. Hamilton ◽  
Marcelo J. Colaço ◽  
Albino J. K. Leiroz ◽  
...  
Keyword(s):  
Heat Release ◽  
Diesel Engines ◽  
Bayesian Estimate ◽  
Marine Diesel ◽  
Rate Of Heat Release
Sign in / Sign up

Export Citation Format

Share Document