Application of High Efficiency Oil Filtration to Heavy Duty Diesel Bus Engines

1992 ◽  
Author(s):  
Mark J. Beauchamp
Keyword(s):  
High Efficiency ◽  
Heavy Duty ◽  
Heavy Duty Diesel ◽  
Oil Filtration

Investigation of Injection Strategies to Improve High Efficiency RCCI Combustion With Diesel and Gasoline Direct Injection

2012 ◽  
Author(s):  
Martin L. Wissink ◽  
Jae H. Lim ◽  
Derek A. Splitter ◽  
Reed M. Hanson ◽  
Rolf D. Reitz
Keyword(s):  
High Efficiency ◽  
Direct Injection ◽  
High Reactivity ◽  
Gasoline Direct Injection ◽  
Cylinder Wall ◽  
Nox Emissions ◽  
Heavy Duty ◽  
Fuel Vaporization ◽  
Heavy Duty Diesel ◽  
Injection Strategies

Experiments were performed to investigate injection strategies for improving engine-out emissions of RCCI combustion in a heavy-duty diesel engine. Previous studies of RCCI combustion using port-injected low-reactivity fuel (e.g., gasoline or iso-octane) and direct-injected high-reactivity fuel (e.g., diesel or n-heptane) have reported greater than 56% gross indicated thermal efficiency while meeting the EPA 2010 heavy-duty PM and NOx emissions regulations in-cylinder. However, CO and UHC emissions were higher than in diesel combustion. This increase is thought to be caused by crevice flows of trapped low-reactivity fuel and lower cylinder wall temperatures. In the present study, both the low- and high-reactivity fuels were direct-injected, enabling more precise targeting of the low-reactivity fuel as well as independent stratification of equivalence ratio and reactivity. Experiments with direct-injection of both gasoline and diesel were conducted at 9 bar IMEP and compared to results from experiments with port-injected gasoline and direct-injected diesel at matched conditions. The results indicate that reductions in UHC, CO, and PM are possible with direct-injected gasoline, while maintaining similar gross indicated efficiency as well as NOx emissions well below the EPA 2010 heavy-duty limit. Additionally, experimental results were simulated using multi-dimensional modeling in the KIVA-3V code coupled to a Discrete Multi-Component fuel vaporization model. The simulations suggest that further UHC reductions can be made by using wider injector angles which direct the gasoline spray away from the crevices.

scholarly journals Effect of Load on Close-Coupled Post-Injection Efficacy for Soot Reduction in an Optical Heavy-Duty Diesel Research Engine

2014 ◽  
Vol 136 (10) ◽  
Author(s):  
Jacqueline O’Connor ◽  
Mark Musculus
Keyword(s):  
High Efficiency ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Optical Measurements ◽  
Injection Timing ◽  
Post Injection ◽  
Heavy Duty ◽  
Wide Range ◽  
Main Injection ◽  
Heavy Duty Diesel

The use of close-coupled post injections is an in-cylinder soot-reduction technique that has much promise for high efficiency heavy-duty diesel engines. Close-coupled post injections, short injections of fuel that occur soon after the end of the main fuel injection, have been known to reduce engine-out soot at a wide range of engine operating conditions, including variations in injection timing, exhaust gas recirculation (EGR) level, load, boost, and speed. While many studies have investigated the performance of post injections, the details of the mechanism by which soot is reduced remains unclear. In this study, we have measured the efficacy of post injections over a range of load conditions, at constant speed, boost, and rail pressure, in a heavy-duty optically-accessible research diesel engine. Here, the base load is varied by changing the main-injection duration. Measurements of engine-out soot indicate that not only does the efficacy of a post injection decrease at higher engine loads, but that the range of post-injection durations over which soot reduction is achievable is limited at higher loads. Optical measurements, including the natural luminescence of soot and planar laser-induced incandescence of soot, provide information about the spatiotemporal development of in-cylinder soot through the cycle in cases with and without post-injections. The optical results indicate that the post injection behaves similarly at different loads, but that its relative efficacy decreases due to the increase in soot resulting from longer main-injection durations.

scholarly journals Effect of Load on Close-Coupled Post-Injection Efficacy for Soot Reduction in an Optical, Heavy-Duty Diesel Research Engine

2013 ◽  
Author(s):  
Jacqueline O’Connor ◽  
Mark P. B. Musculus
Keyword(s):  
High Efficiency ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Optical Measurements ◽  
Injection Timing ◽  
Post Injection ◽  
Heavy Duty ◽  
Wide Range ◽  
Main Injection ◽  
Heavy Duty Diesel

The use of close-coupled post injections of fuel is an in-cylinder soot-reduction technique that has much promise for high efficiency, heavy-duty diesel engines. Close-coupled post injections, short injections of fuel that occur soon after the end of the main fuel injection, have been known to reduce engine-out soot at a wide range of engine operating conditions, including variations in injection timing, EGR level, load, boost, and speed. While many studies have investigated the performance of post injections, the details of the mechanism by which soot is reduced remains unclear. In this study, we have measured the efficacy of post injections over a range of load conditions, at constant speed, boost, and rail pressure, in a heavy-duty, optically-accessible research diesel engine. Here, the base load is varied by changing the main-injection duration. Measurements of engine-out soot indicate that not only does the efficacy of a post injection decrease at higher engine loads, but that the range of post-injection durations over which soot reduction is achievable is limited at higher loads. Optical measurements, including natural luminescence of soot and planar laser-induced incandescence of soot, provide information about the spatio-temporal development of in-cylinder soot through the cycle in cases with and without post injections. The optical results indicate that the post injection behaves similarly at different loads, but that its relative efficacy decreases due to the increase in soot resulting from longer main-injection durations.

scholarly journals Particulate emissions of heavy duty diesel engines measured from the tailpipe and the dilution tunnel

2021 ◽  
pp. 105799
Author(s):  
Sheng Su ◽  
Tao Lv ◽  
Yitu Lai ◽  
Jinsong Mu ◽  
Yunshan Ge ◽  
...  
Keyword(s):  
Diesel Engines ◽  
Particulate Emissions ◽  
Heavy Duty ◽  
Heavy Duty Diesel

scholarly journals Effects of renewable fuel and exhaust aftertreatment on primary and secondary emissions from a modern heavy-duty diesel engine

2021 ◽  
Vol 156 ◽  
pp. 105781
Author(s):  
Louise Gren ◽  
Vilhelm B. Malmborg ◽  
John Falk ◽  
Lassi Markula ◽  
Maja Novakovic ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Exhaust Aftertreatment ◽  
Heavy Duty ◽  
Renewable Fuel ◽  
Heavy Duty Diesel Engine ◽  
Heavy Duty Diesel
Sign in / Sign up

Export Citation Format

Share Document