New Mixture Formation Technology of Direct Fuel Injection Stratified Combustion SI Engine (OSKA)

1987 ◽  
Author(s):  
Satoshi Kato ◽  
Shigeru Onishi
Keyword(s):  
Fuel Injection ◽  
Si Engine ◽  
Mixture Formation ◽  
Stratified Combustion ◽  
Direct Fuel Injection

Study of Mixture Formation on Gasoline Direct Fuel Injection Engines

2002 ◽  
Vol 2002 (0) ◽  
pp. 57-58
Author(s):  
Noboru TOKUYASU ◽  
Yoshihiro SUKEGAWA ◽  
Toshiharu NOGI
Keyword(s):  
Fuel Injection ◽  
Mixture Formation ◽  
Direct Fuel Injection

scholarly journals COMPARISON OF COMBUSTION INDICATORS OF TWO-STROKE ENGINES WITH A CARBURETOR AND DIRECT FUEL INJECTION

2021 ◽  
pp. 35-44
Author(s):  
V.A. Korohodskyi
Keyword(s):  
Heat Release ◽  
Fuel Injection ◽  
Combustion Process ◽  
Expansion Ratio ◽  
Mixture Formation ◽  
Load Characteristic ◽  
Combustion Pressure ◽  
Maximum Value ◽  
Characteristic Modes ◽  
Direct Fuel Injection

The subject matter of study in the article is the indicators of the combustion process of a two-stroke engine 1D 8.7 / 8.2 with spark ignition when using a carburetor power supply system (external mixture formation) and a direct fuel injection system (internal mixture formation). Internal mixture formation ensures the organization of a stratified fuel-air charge (SFAC) and a stratified lean fuel-air charge (SLFAC). Combustion indicators allow you to assess the nature of the combustion process. The goal is to determine the nature of the change in the combustion indicators of the engine with external and internal mixture formation during the organization of the working process with the SFAC and SLFAC at the load characteristic modes (n = 3,000 rpm). The tasks to be solved are as follows. The use of internal mixture formation and the organization of the combustion of SLFAC and SFAC made it possible to obtain values of ηi greater than with external mixture formation at all modes of the load characteristic. The maximum value of ηi for SLFAC is 0.5 at a load bmep = 0.2 MPa, for SFAC – 0.44 at bmep = 0.25 MPa and 0.3 at bmep = 0.36 MPa for an engine with a carburettor. Maximum combustion pressure (рz), pressure increase ratio (λ), preliminary expansion ratio (ρ), further expansion ratio (δ), combustion character indicator (m), maximum heat release rate (dx / dfi max), duration of combustion from TDC to point Z (φz), total duration of combustion (dφz); to construct the characteristics of changes in combustion indicators and to obtain empirical dependences depending on the engine load. An experimental-analytical research method is used, which provides for the determination of the nature and analysis of the course of the combustion process according to the combustion indicators established by the experimental indicator diagrams. The following results were obtained. The use of internal mixture formation and the organization of the combustion of SFAC and SLFAC made it possible to obtain ηi values greater than with external mixture formation at all modes of the load characteristic. The maximum value of ηi for SLFAC is 0.5 at a load ре = 0.2 MPa, for SFAC - 0.44 at ре = 0.25 MPa and 0.3 at ре = 0.36 MPa for an engine with a carburetor. The pressure in the cylinder with the piston position at TDC is on average 1.5 times higher for an engine with a carburetor, and the maximum combustion pressure рz is higher up to 11 % with the organization of SLFAC (the degree of pressure increase λ is reduced by 26 %) and 20-22 % higher than in the organization of SFAC (the value of λ is reduced by 31 %). An increase in the compression ratio ε by 26.4 % and a decrease in the degree of preliminary expansion ρ at SLFAC in comparison with SFAC made it possible to increase the degree of further expansion δ by an average of 30 % and by 43 % in comparison with the carburetor power system. When organizing SLFAC, the value of the indicator of the nature of combustion m is, on average, 1.4 times higher than that of an engine with a carburetor and 1.45 times higher relative to the organization of SFAC, at which the maximum rate of heat release dx / dfi max is up to 40 % higher than in the engine with carburetor. The SLFAC organization allowed reduce the combustion duration by 39 % relative to external mixture formation and by 36 % relative to the SFAC organization. Conclusions. The scientific novelty of the results obtained consists in obtaining data and empirical dependences of the indicators of the combustion process of the 1D 8.7 / 8.2 engine with external and internal mixture formation with the organization of SFAC and SLFAC at load characteristic modes (n = 3,000 rpm). It was found that the best technical, economic and environmental indicators correspond to the organization of internal mixing with SLFAC.

Particulate matter emissions from flex-fuel vehicles with direct fuel injection

2021 ◽  
pp. 101078
Author(s):  
Luiz C. Daemme ◽  
Renato Penteado ◽  
Rodrigo S. Ferreira ◽  
Marcelo R. Errera ◽  
Sergio M. Corrêa ◽  
...  
Keyword(s):  
Particulate Matter ◽  
Fuel Injection ◽  
Particulate Matter Emissions ◽  
Flex Fuel ◽  
Direct Fuel Injection
Sign in / Sign up

Export Citation Format

Share Document