Squeeze Casting Process for Metal-Ceramic Composites

1987 ◽  
Author(s):  
Suresh K. Verma ◽  
John L. Dorcic
Keyword(s):  
Squeeze Casting ◽  
Casting Process ◽  
Ceramic Composites ◽  
Metal Ceramic ◽  
Squeeze Casting Process

scholarly journals Investigations on coating of dies for advanced squeeze casting process

2014 ◽  
Vol 20 (1) ◽  
Author(s):  
Ildiko Peter ◽  
Mario Rosso ◽  
Christian Castella
Keyword(s):  
Squeeze Casting ◽  
Casting Process ◽  
Squeeze Casting Process

Development of Steel Wire Rope – Reinforced Aluminium Composite for Armour Material Using the Squeeze Casting Process

2011 ◽  
Vol 277 ◽  
pp. 27-35 ◽  
Author(s):  
Dwi Rahmalina ◽  
Bondan Tiara Sofyan ◽  
Bambang Suharno ◽  
Eddy S. Siradj
Keyword(s):  
Squeeze Casting ◽  
Steel Wire ◽  
High Carbon Steel ◽  
Casting Process ◽  
Optical Microscope ◽  
Wire Rope ◽  
Aluminium Composite ◽  
Ballistic Properties ◽  
Semi Solid ◽  
Squeeze Casting Process

Steel wire rope – reinforced aluminium composite - has been developed to improve the ballistic properties and mobility of armour material. Critical to obtaining ballistic resistance is that the materials must be sufficiently hard and strong, especially at the surface where a projectile will first make impact. To obtain this resistance, aluminium alloys can be strengthened by adding Cu and Mg. This research studied the ballistic properties of aluminium composites with varied Cu and Mg content. The matrix used in this study was an Al-7Si master alloy with 0.08-1.03 wt. % Mg and 0.05-3.75 wt. % Cu, both independently and in combination. A high carbon steel wire rope was used as strengthening material. The samples were produced through the squeeze casting process with a pressure of 1 MPa at semi-solid melting temperatures of 590-610 °C. The slab was then rolled for 10 % reduction to increase the hardness. Ballistic testing was performed in accordance with ASTM F1233 by using a 9 mm calibre projectile and 900 direction. Micro structural observation was conducted in the as-cast and ballistic samples, performed with optical microscope and scanning electron microscope (SEM). The results showed that squeeze casting may improve interfacial wettability and reduce void. The increase in Mg resulted in the decline of interfacial voids, but Cu addition tended to increase them. The aluminium armour was able to withstand a 9 mm calibre projectile, although some cracks were visible. The wire rope was not effective in stopping the penetration of a 7.62 mm calibre projectile.

Investigation of mechanical properties on Al 6061-B4C composite by squeeze casting process technique

2019 ◽  
Vol 1 (1) ◽  
pp. 38-48
Author(s):  
A. Sathishkumar ◽  
Gowtham A ◽  
M. Jeyasuriya ◽  
S. DineshBabu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Metal Matrix ◽  
Squeeze Casting ◽  
Casting Process ◽  
Weight Fraction ◽  
Squeeze Pressure ◽  
B4c Particles ◽  
Engineering Industries ◽  
Squeeze Casting Process

Aluminum alloy is widely used in automotive, aerospace and other engineering industries because of its excellent mechanical properties. The main objective is to enhance 6061 Al alloy’s mechanical properties by producing 6061-B4C composite through squeeze casting process. Experimentation was carried out with different micron sizes and weight fraction of B4C particles. The mechanical properties of reinforced metal matrix were experimentally investigated in terms of Ultimate Tensile Strength and Hardness. We observe that these two properties are improved by the reinforcement of B4C particles and applied squeeze pressure.

Die Design for Main Bearing Cap of Engine Block Based Semi-Solid Die Casting Process and the Comparison Analysis with Squeeze Casting Process

2019 ◽  
Vol 285 ◽  
pp. 429-435 ◽  
Author(s):  
Song Chen ◽  
Da Quan Li ◽  
Fan Zhang ◽  
Min Luo ◽  
Xiao Kang Liang ◽  
...  
Keyword(s):  
Squeeze Casting ◽  
Die Casting ◽  
Dendritic Structure ◽  
Casting Process ◽  
Die Design ◽  
Main Bearing ◽  
Block Based ◽  
Semi Solid ◽  
Bearing Cap ◽  
Squeeze Casting Process

There are two new processes to development automobile structural components which have certain thickness. In the present paper, taking a main bearing cap product as an example, analyses die design by comparing the experimental and computational numerical simulation results. For the main bearing cap, product structure and mold design were designed to be suitable for characters of SSM die casting and squeeze process. Semi-solid slurry has significantly higher viscosity than liquid metal. This character of fluidity and solid fraction phase make the flow condition more laminar than liquid squeeze casting with the partial fill experiment. And compared with squeeze casting process, the globular shape grain size is smaller than dendritic structure. And mechanical property result shows that the elongation of SSM die casting can achieve more than twice than squeeze casting.

Sign in / Sign up

Export Citation Format

Share Document