Influence of Fuel Drop Size and Combustor Operating Conditions on Pollutant Emissions

1986 ◽  
Author(s):  
K. K. Rink ◽  
A. H. Lefebvre
Keyword(s):  
Drop Size ◽  
Operating Conditions ◽  
Pollutant Emissions

scholarly journals Influence of Fuel Composition and Spray Characteristics on Nitric Oxide Formation

1989 ◽  
Author(s):  
K. K. Rink ◽  
A. H. Lefebvre
Keyword(s):  
Nitric Oxide ◽  
Drop Size ◽  
Perforated Plate ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Fuel Composition ◽  
Circular Array ◽  
Nitric Oxide Formation ◽  
Nitric Oxide Emissions ◽  
Standard Instrumentation

Measurements of nitric oxide emissions are carried out on a continuous flow combustor when operating over wide ranges of fuel/air ratio at pressures up to 1.52 MPa (15 atmos). Fuel is supplied to the flame zone from a circular array of 30 equispaced miniature airblast atomizers which is incorporated into a perforated-plate flameholder. Standard instrumentation and sampling techniques are used to measure pollutant emissions over wide ranges of mean fuel drop size. The results obtained with several selected fuels demonstrate the effects of variations in fuel composition, fuel drop size, and combustor operating conditions on nitric oxide emissions.

Prediction of gaseous pollutant emissions from a spark-ignition direct-injection engine with gas-exchange simulation

2021 ◽  
pp. 146808742110050
Author(s):  
Stefania Esposito ◽  
Lutz Diekhoff ◽  
Stefan Pischinger
Keyword(s):  
Gas Exchange ◽  
Combustion Chamber ◽  
Direct Injection ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Operating Parameters ◽  
Gaseous Pollutant ◽  
Fuel Ratio ◽  
No Emissions

With the further tightening of emission regulations and the introduction of real driving emission tests (RDE), the simulative prediction of emissions is becoming increasingly important for the development of future low-emission internal combustion engines. In this context, gas-exchange simulation can be used as a powerful tool for the evaluation of new design concepts. However, the simplified description of the combustion chamber can make the prediction of complex in-cylinder phenomena like emission formation quite challenging. The present work focuses on the prediction of gaseous pollutants from a spark-ignition (SI) direct injection (DI) engine with 1D–0D gas-exchange simulations. The accuracy of the simulative prediction regarding gaseous pollutant emissions is assessed based on the comparison with measurement data obtained with a research single cylinder engine (SCE). Multiple variations of engine operating parameters – for example, load, speed, air-to-fuel ratio, valve timing – are taken into account to verify the predictivity of the simulation toward changing engine operating conditions. Regarding the unburned hydrocarbon (HC) emissions, phenomenological models are used to estimate the contribution of the piston top-land crevice as well as flame wall-quenching and oil-film fuel adsorption-desorption mechanisms. Regarding CO and NO emissions, multiple approaches to describe the burned zone kinetics in combination with a two-zone 0D combustion chamber model are evaluated. In particular, calculations with reduced reaction kinetics are compared with simplified kinetic descriptions. At engine warm operation, the HC models show an accuracy mainly within 20%. The predictions for the NO emissions follow the trend of the measurements with changing engine operating parameters and all modeled results are mainly within ±20%. Regarding CO emissions, the simplified kinetic models are not capable to predict CO at stoichiometric conditions with errors below 30%. With the usage of a reduced kinetic mechanism, a better prediction capability of CO at stoichiometric air-to-fuel ratio could be achieved.

Break-Up of Threads From Laminar Open Channel Flow Influenced by Cross-Wind Gas Flow

2014 ◽  
Author(s):  
Jens Kamplade ◽  
Tobias Mack ◽  
Andre Küsters ◽  
Peter Walzel
Keyword(s):  
Size Distribution ◽  
Channel Flow ◽  
Gas Flow ◽  
Drop Size ◽  
Open Channel ◽  
Open Channel Flow ◽  
Drop Size Distribution ◽  
Operating Conditions ◽  
Breakup Process ◽  
Breakup Length

The breakup process of threads from laminar operating rotary atomizer (LamRot) is in the scope of this investigation. A similarity trail is used to investigate the influence of the thread deformation within a cross-wind flow on the thread breakup process. The threads emerge from laminar open channel flow while the liquid viscosity, the flow rate, the pipe inclination towards the gravity as well as the cross-wind velocity is varied. The breakup length and drop size distribution are analyzed by a back-light photography setup. The results thus obtained are compared with results of previous examination by Schröder [1] and Mescher [2]. It is found that the breakup length decreases and that the drop size grows with rising cross-wind intensity, while the width of the drop size distribution increases. At the same operating conditions, the breakup length for laminar open channel flow is smaller compared to completely filled capillaries. In contrast to this observation, the drop size distribution remains nearly unchanged. The critical velocity for the transition from axisymmetric to wind-induced thread breakup was found to be smaller than for completely filled capillaries.

scholarly journals Measurement of Air-Fuel Ratio Fluctuations Caused by Combustor Driven Oscillations

1998 ◽  
Author(s):  
Rajiv Mongia ◽  
Robert Dibble ◽  
Jeff Lovett
Keyword(s):  
Power Spectrum ◽  
Mole Fraction ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Premixed Combustion ◽  
Pollutant Emissions ◽  
Combustion Instabilities ◽  
Pressure Oscillations ◽  
Lean Premixed Combustion ◽  
Lean Premixed

Lean premixed combustion has emerged as a method of achieving low pollutant emissions from gas turbines. A common problem of lean premixed combustion is combustion instability. As conditions inside lean premixed combustors approach the lean flammability limit, large pressure variations are encountered. As a consequence, certain desirable gas turbine operating regimes are not approachable. In minimizing these regimes, combustor designers must rely upon trial and error because combustion instabilities are not well understood (and thus difficult to model). When they occur, pressure oscillations in the combustor can induce fluctuations in fuel mole fraction that can augment the pressure oscillations (undesirable) or dampen the pressure oscillations (desirable). In this paper, we demonstrate a method for measuring the fuel mole fraction oscillations which occur in the premixing section during combustion instabilities produced in the combustor that is downstream of the premixer. The fuel mole fraction in the premixer is measured with kHz resolution by the absorption of light from a 3.39 μm He-Ne laser. A sudden expansion combustor is constructed to demonstrate this fuel mole fraction measurement technique. Under several operating conditions, we measure significant fuel mole fraction fluctuations that are caused by pressure oscillations in the combustion chamber. Since the fuel mole fraction is sampled continuously, a power spectrum is easily generated. The fuel mole fraction power spectrum clearly indicates fuel mole fraction fluctuation frequencies are the same as the pressure fluctuation frequencies under some operating conditions.

Research on Additional Specific Consumption Distribution of Biomass Direct Combustion Power Plant

2011 ◽  
Vol 347-353 ◽  
pp. 631-634
Author(s):  
Qin Liang Tan ◽  
Cai Juan Zhang ◽  
Xiao Ying Hu ◽  
Li Gang Wang ◽  
Qiang Lu ◽  
...  
Keyword(s):  
Power Plant ◽  
Energy Saving ◽  
Second Law Of Thermodynamics ◽  
Operating Conditions ◽  
Specific Consumption ◽  
Pollutant Emissions ◽  
Design Parameters ◽  
Direct Combustion ◽  
Analysis Theory ◽  
Biomass Power Plant

Biomass direct combustion power generation is the most simple but effective way in dealing with environmental issues and energy crisis. A comprehensive diagnosis with accurate evaluation of energy saving potential of a given biomass power plant is of great importance in lowing the cost of generating electricity, reducing the consumption of energy and pollutant emissions [1]. This paper throws light upon an innovative energy consumption diagnosis method-the specific consumption analysis theory, which is based on the First and Second law of thermodynamics [2,3]. Taking a given biomass power plant of National Energy Group as an example, mathematical models are made based on all the components and processes. The specific consumption analysis theory is employed to calculate the specific consumption within the biomass power plant using design parameters under design operating conditions, thus demonstrating the specific consumption distribution in the power plant, which provides theoretical basis for energy-saving and optimization in biomass power plant.

Modelling Strategies for Large-Eddy Simulation of Lean Burn Spray Flames

2017 ◽  
Author(s):  
S. Puggelli ◽  
D. Bertini ◽  
L. Mazzei ◽  
A. Andreini
Keyword(s):  
Large Eddy Simulation ◽  
Ambient Pressure ◽  
Nox Reduction ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Lean Burn ◽  
Eddy Simulation ◽  
Flamelet Generated Manifold ◽  
Large Eddy ◽  
Modelling Strategies

During the last years aero-engines are progressively evolving toward design concepts that permit improvements in terms of engine safety, fuel economy and pollutant emissions. With the aim of satisfying the strict NOx reduction targets imposed by ICAO-CAEP, lean burn technology is one of the most promising solutions even if it must face safety concerns and technical issues. Hence a depth insight on lean burn combustion is required and Computational Fluid Dynamics (CFD) can be a useful tool for this purpose. In this work a comparison in Large-Eddy Simulation (LES) framework of two widely employed combustion approaches like the Artificially Thickened Flame (ATF) and the Flamelet Generated Manifold (FGM) is performed using ANSYS® Fluent v16.2. Two literature test cases with increasing complexity in terms of geometry, flow field and operating conditions are considered. Firstly, capabilities of FGM are evaluated on a single swirler burner operating at ambient pressure with a standard pressure atomizer for spray injection. Then a second test case, operated at 4 bar, is simulated. Here kerosene fuel is burned after an injection through a prefilming airblast atomizer within a co-rotating double swirler. Obtained comparisons with experimental results show the different capabilities of ATF and FGM in modelling the partially-premixed behaviour of the flame and provides an overview of the main strengths and limitations of the modelling strategies under investigation.

Introduction of the Taurus™ 65 Industrial Gas Turbine for Power Generation

2008 ◽  
Author(s):  
George Rocha ◽  
Simon Reynolds ◽  
Theresa Brown
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Electrical Power ◽  
Field Evaluation ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Liquid Fuels ◽  
Operating Cycle ◽  
Product Experience ◽  
Exhaust Heat

Solar Turbines Incorporated has combined proven technology and product experience to develop the new Taurus 65 gas turbine for industrial power generation applications. The single-shaft engine is designed to produce 6.3 megawatts of electrical power with a 33% thermal efficiency at ISO operating conditions. Selection of the final engine operating cycle was based on extensive aerodynamic-cycle studies to achieve optimum output performance with increased exhaust heat capacity for combined heat and power installations. The basic engine configuration features an enhanced version of the robust Centaur®50 air compressor coupled to a newly designed three-stage turbine similar to the Taurus 70 turbine design. Advanced cooling technology and materials are used in the dry, lean-premix annular combustor, consistent with Solar’s proven SoLoNOx™ combustion technology, capable of reducing pollutant emissions while operating on standard natural gas or diesel liquid fuels. Like the Titan™ 130 and Taurus 70 products, a traditional design philosophy has been applied in development of the Taurus 65 gas turbine by utilizing existing components, common technology and product experience to minimize risk, lower cost and maximize durability. A comprehensive factory test plan and extended field evaluation program was used to validate the design integrity and demonstrate product durability prior to full market introduction.

Influence of Low Ambient Temperatures on the Exhaust Gas and Deposit Composition of Gasoline Engines

2021 ◽  
pp. 1-11
Author(s):  
Dominik Appel ◽  
Fabian P. Hagen ◽  
Uwe Wagner ◽  
Thomas Koch ◽  
Henning Bockhorn ◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Gasoline Engine ◽  
Cold Start ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Ex Situ ◽  
Exhaust Gas ◽  
Gasoline Engines ◽  
Ambient Temperatures ◽  
Aftertreatment Systems

Abstract To comply with future emission regulations for internal combustion engines, system-related cold-start conditions in short-distance traffic constitute a particular challenge. Under these conditions, pollutant emissions are seriously increased due to internal engine effects and unfavorable operating conditions of the exhaust aftertreatment systems. As a secondary effect, the composition of the exhaust gases has a considerable influence on the deposition of aerosols via different deposition mechanisms and on fouling processes of exhaust gas-carrying components. Also, the performance of exhaust gas aftertreatment systems may be affected disadvantageously. In this study, the exhaust gas and deposit composition of a turbocharged three-cylinder gasoline engine is examined in-situ upstream of the catalytic converter at ambient and engine starting temperatures of -22 °C to 23 °C using a Fourier-transform infrared spectrometer and a particle spectrometer. For the cold start investigation, a modern gasoline engine with series engine periphery is used. In particular, the investigation of the behavior of deposits in the exhaust system of gasoline engines during cold start under dynamic driving conditions represents an extraordinary challenge due to an average lower soot concentration in the exhaust gas compared to diesel engines and so far, has not been examined in this form. A novel sampling method allows ex-situ analysis of formed deposits during a single driving cycle. Both, particle number concentration and the deposition rate are higher in the testing procedure of Real Driving Emissions (RDE) than in the inner-city part of the Worldwide harmonized Light vehicles Test Cycle (WLTC). In addition, reduced ambient temperatures increase the amount of deposits, which consist predominantly of soot and to a minor fraction of volatile compounds. Although the primary particle size distributions of the deposited soot particles do not change when boundary conditions change, the degree of graphitization within the particles increases with increasing exhaust gas temperature.

scholarly journals Test campaign of a ducted wind turbine in real operating conditions

2019 ◽  
Vol 113 ◽  
pp. 03005
Author(s):  
Enrico Valditerra ◽  
Massimo Rivarolo ◽  
Aristide F. Massardo ◽  
Marco Gualco
Keyword(s):  
Wind Turbine ◽  
Urban Areas ◽  
Energy Production ◽  
Electrical Energy ◽  
Clean Energy ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Ambient Conditions ◽  
Wind Speeds ◽  
Electrical Energy Production

Wind turbine installation worldwide has increased at unrested pace, as it represents a 100% clean energy with zero CO2 and pollutant emissions. However, visual and acoustic impact of wind turbines is still a drawback, in particular in urban areas. This paper focuses on the performance evaluation of an innovative horizontal axis ducted wind turbine, installed in the harbour of Genova (Italy) in 2018: the turbine was designed in order to minimize visual and acoustic impacts and maximize electrical energy production, also during low wind speed periods. The preliminary study and experimental analyses, performed by the authors in a previous study, showed promising results in terms of energy production, compared to a traditional generator ( factor >2.5 on power output). In the present paper, the test campaign on a scaled-up prototype, installed in the urban area of Genova, is performed, with a twofold objective: (i) comparison of the ducted innovative turbine with a standard one, in order to verify the increase in energy production; (ii) analysis of the innovative turbine for different wind speeds and directions, evaluating the influence of ambient conditions on performance. Finally, based on the obtained results, an improved setup is proposed for the ducted wind turbine, in order to further increase energy production mitigating its visual impact.

scholarly journals Effect of Fuel and Air Dilution on Syngas Combustion in an Optical SI Engine

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1566 ◽  
Author(s):  
S.D. Martinez-Boggio ◽  
S.S. Merola ◽  
P. Teixeira Lacava ◽  
A. Irimescu ◽  
P.L. Curto-Risso
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Process ◽  
Visible Spectrum ◽  
Propagation Speed ◽  
Fuel Mixture ◽  
Operating Conditions ◽  
Inert Gases ◽  
Pollutant Emissions ◽  
Si Engine ◽  
Lean Burn

To mitigate the increasing concentration of carbon dioxide in the atmosphere, energy production processes must change from fossil to renewable resources. Bioenergy utilization from agricultural residues can be a step towards achieving this goal. Syngas (fuel obtained from biomass gasification) has been proved to have the potential of replacing fossil fuels in stationary internal combustion engines (ICEs). The processes associated with switching from traditional fuels to alternatives have always led to intense research efforts in order to have a broad understanding of the behavior of the engine in all operating conditions. In particular, attention needs to be focused on fuels containing relatively high concentrations of hydrogen, due to its faster propagation speed with respect to traditional fossil energy sources. Therefore, a combustion study was performed in a research optical SI engine, for a comparison between a well-established fuel such as methane (the main component of natural gas) and syngas. The main goal of this work is to study the effect of inert gases in the fuel mixture and that of air dilution during lean fuelling. Thus, two pure syngas blends (mixtures of CO and H2) and their respective diluted mixtures (CO and H2 with 50vol% of inert gases, CO2 and N2) were tested in several air-fuel ratios (stoichiometric to lean burn conditions). Initially, the combustion process was studied in detail by traditional thermodynamic analysis and then optical diagnostics were applied thanks to the optical access through the piston crown. Specifically, images were taken in the UV-visible spectrum of the entire cycle to follow the propagation of the flame front. The results show that hydrogen promotes flame propagation and reduces its distortion, as well as resulting in flames evolving closer to the spark plug. All syngas blends show a stable combustion process, even in conditions of high air and fuel dilution. In the leanest case, real syngas mixtures present a decrease in terms of performance due to significant reduction in volumetric efficiency. However, this condition strongly decreases pollutant emissions, with nitrogen oxide (NOx) concentrations almost negligible.

Sign in / Sign up

Export Citation Format

Share Document