Application of the Vortex-Lattice Method to High-Angle-of-Attack Subsonic Aerodynamics

1985 ◽  
Author(s):  
Dean T. Mook ◽  
Ali H. Nayfeh
Keyword(s):  
Vortex Lattice ◽  
Angle Of Attack ◽  
High Angle ◽  
Lattice Method ◽  
High Angle Of Attack ◽  
Vortex Lattice Method

Calculation of the Aerodynamic Forces on Automotive Lifting Surfaces

1985 ◽  
Vol 107 (4) ◽  
pp. 438-443 ◽  
Author(s):  
J. Katz
Keyword(s):  
Steady State ◽  
Vortex Lattice ◽  
Numerical Technique ◽  
Angle Of Attack ◽  
Ground Effect ◽  
Aerodynamic Forces ◽  
Lattice Method ◽  
Vortex Lattice Method ◽  
Close Proximity ◽  
Lifting Surfaces

A numerical technique was developed to investigate the performance of automotive lifting surfaces in close proximity to ground. The model is based on the Vortex Lattice Method and includes freely-deforming wake elements. The ground effect was simulated by reflection and both steady and unsteady pressures and loads on various wing planforms were considered. Calculated results are presented for wings having both positive and negative incidences, with and without ground effect. Also the transient lift of a wing in a plunging motion was analyzed in ground proximity and at a negative angle of attack. Finally the periodic lift fluctuations on the front winglet of a racing car, due to its suspension oscillations, were calculated and found to exceed approximately twice the steady-state value.

Generalized vortex lattice method for planar supersonic flow

AIAA Journal ◽  
1997 ◽  
Vol 35 ◽  
pp. 1230-1233
Author(s):  
Paulo A. O. Soviero ◽  
Hugo B. Resende
Keyword(s):  
Supersonic Flow ◽  
Vortex Lattice ◽  
Lattice Method ◽  
Vortex Lattice Method

scholarly journals Static Aeroelastic Characteristics of Morphing Trailing-Edge Wing Using Geometrically Exact Vortex Lattice Method

2019 ◽  
Vol 2019 ◽  
pp. 1-15
Author(s):  
Sen Mao ◽  
Changchuan Xie ◽  
Lan Yang ◽  
Chao Yang
Keyword(s):  
Vortex Lattice ◽  
Deflection Angle ◽  
Aircraft Design ◽  
Analysis Method ◽  
Lattice Method ◽  
Trailing Edge ◽  
Vortex Lattice Method ◽  
Analysis And Design ◽  
Aeroelastic Analysis ◽  
Typical Model

A morphing trailing-edge (TE) wing is an important morphing mode in aircraft design. In order to explore the static aeroelastic characteristics of a morphing TE wing, an efficient and feasible method for static aeroelastic analysis has been developed in this paper. A geometrically exact vortex lattice method (VLM) is applied to calculate the aerodynamic forces. Firstly, a typical model of a morphing TE wing is chosen and built which has an active morphing trailing edge driven by a piezoelectric patch. Then, the paper carries out the static aeroelastic analysis of the morphing TE wing and corresponding simulations were carried out. Finally, the analysis results are compared with those of a traditional wing with a rigid trailing edge using the traditional linearized VLM. The results indicate that the geometrically exact VLM can better describe the aerodynamic nonlinearity of a morphing TE wing in consideration of geometrical deformation in aeroelastic analysis. Moreover, out of consideration of the angle of attack, the deflection angle of the trailing edge, among others, the wing system does not show divergence but bifurcation. Consequently, the aeroelastic analysis method proposed in this paper is more applicable to the analysis and design of a morphing TE wing.

scholarly journals Leading Edge Blowing to Mimic and Enhance the Serration Effects for Aerofoil

2021 ◽  
Vol 11 (6) ◽  
pp. 2593
Author(s):  
Yasir Al-Okbi ◽  
Tze Pei Chong ◽  
Oksana Stalnov
Keyword(s):  
Boundary Layer ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Boundary Layer Separation ◽  
Shear Instability ◽  
Vortical Flow ◽  
High Angle ◽  
High Angle Of Attack ◽  
Layer Separation ◽  
Aerodynamic Performances

Leading edge serration is now a well-established and effective passive control device for the reduction of turbulence–leading edge interaction noise, and for the suppression of boundary layer separation at high angle of attack. It is envisaged that leading edge blowing could produce the same mechanisms as those produced by a serrated leading edge to enhance the aeroacoustics and aerodynamic performances of aerofoil. Aeroacoustically, injection of mass airflow from the leading edge (against the incoming turbulent flow) can be an effective mechanism to decrease the turbulence intensity, and/or alter the stagnation point. According to classical theory on the aerofoil leading edge noise, there is a potential for the leading edge blowing to reduce the level of turbulence–leading edge interaction noise radiation. Aerodynamically, after the mixing between the injected air and the incoming flow, a shear instability is likely to be triggered owing to the different flow directions. The resulting vortical flow will then propagate along the main flow direction across the aerofoil surface. These vortical flows generated indirectly owing to the leading edge blowing could also be effective to mitigate boundary layer separation at high angle of attack. The objectives of this paper are to validate these hypotheses, and combine the serration and blowing together on the leading edge to harvest further improvement on the aeroacoustics and aerodynamic performances. Results presented in this paper strongly indicate that leading edge blowing, which is an active flow control method, can indeed mimic and even enhance the bio-inspired leading edge serration effectively.

Sign in / Sign up

Export Citation Format

Share Document