Design Considerations for Full-Size, Front-Wheel-Drive Vehicles

1975 ◽  
Author(s):  
Donald L. Nordeen ◽  
Richard C. Manwaring ◽  
Dennis E. Condon
Keyword(s):  
Front Wheel ◽  
Full Size ◽  
Design Considerations ◽  
Wheel Drive

Regular perturbations to the motion of a three-wheeled mobile robot with the front-wheel drive under restricted state variables*

2020 ◽  
Author(s):  
Roman Chertovskih ◽  
Anna Daryina ◽  
Askhat Diveev ◽  
Dmitry Karamzin ◽  
Fernando L. Pereira ◽  
...  
Keyword(s):  
Mobile Robot ◽  
Front Wheel ◽  
Wheeled Mobile Robot ◽  
State Variables ◽  
Wheel Drive

scholarly journals Ground maneuver for front-wheel drive aircraft via deep reinforcement learning

2021 ◽  
Author(s):  
Hao Zhang ◽  
Zongxia Jiao ◽  
Yaoxing Shang ◽  
Xiaochao Liu ◽  
Pengyuan Qi ◽  
...  
Keyword(s):  
Reinforcement Learning ◽  
Front Wheel ◽  
Wheel Drive

Modeling of nonlinear torsional vibration of the automotive powertrain

2016 ◽  
Vol 24 (9) ◽  
pp. 1774-1786 ◽  
Author(s):  
Sérgio J Idehara ◽  
Fernando L Flach ◽  
Douglas Lemes
Keyword(s):  
Natural Frequency ◽  
Torsional Vibration ◽  
Degrees Of Freedom ◽  
Front Wheel ◽  
Torsional Stiffness ◽  
Bench Test ◽  
Passenger Car ◽  
Engine Torque ◽  
Friction Moment ◽  
Wheel Drive

A vibration model of the powertrain can be used to predict its dynamic behavior when excited by fluctuations in the engine torque and speed. The torsional vibration resulting from torque and speed fluctuations increases the rattle noise in the gearbox and it should be controlled or minimized in order to gain acceptance by clients and manufactures. The fact that the proprieties of the torsional damper integrated into the clutch disc alter the dynamic characteristic of the system is important in the automotive industry for design purposes. In this study, bench test results for the characteristics of a torsional damper for a clutch system (torsional stiffness and friction moment) and powertrain torsional vibration measurements taken in a passenger car were used to verify and calibrate the model. The adjusted model estimates the driveline natural frequency and the time response vibration. The analysis uses order tracking signal processing to isolate the response from the engine excitation (second-order). It is shown that a decrease in the stiffness of the clutch disc torsional damper lowers the natural frequency and an increase in the friction moment reduces the peak amplitude of the gearbox torsional vibration. The formulation and model adjustment showed that a nonlinear model with three degrees of freedom can represent satisfactorily the powertrain dynamics of a front-wheel drive passenger car.

scholarly journals Traction performance simulation for mechanical front wheel drive tractors: towards a practical computer tool

2013 ◽  
Vol 44 (2s) ◽  
Author(s):  
A. Battiato ◽  
E. Diserens ◽  
L. Sartori
Keyword(s):  
Field Tests ◽  
Front Wheel ◽  
Arable Soils ◽  
Wheel Load ◽  
Computer Tool ◽  
Performance Simulation ◽  
Wheel Drive ◽  
Silty Loam ◽  
Pulling Force ◽  
Drawbar Pull

An analytical model to simulate the traction performance of mechanical front wheel drive MFWD tractors was developed at the Agroscope Reckenholz-Tänikon ART. The model was validated via several field tests in which the relationship between drawbar pull and slip was measured for four MFWD tractors of power ranging between 40 and 123 kW on four arable soils of different texture (clay, clay loam, silty loam, and loamy sand). The pulling tests were carried out in steady-state controlling the pulling force along numerous corridors. Different configurations of tractors were considered by changing the wheel load and the tyre pressure. Simulations of traction performance matched experimental results with good agreement (mean error of 8% with maximum and minimum values of 17% and 1% respectively). The model was used as framework for developing a new module for the excel application TASCV3.0.xlsm, a practical computer tool which compares different tractor configurations, soil textures and conditions, in order to determine variants which make for better traction performance, this resulting in saving fuel and time, i.e. reducing the costs of tillage management.

Drive and Brake Joint Control of Acceleration Slip Regulation Road Test

2014 ◽  
Vol 971-973 ◽  
pp. 454-457
Author(s):  
Gang He ◽  
Li Qiang Jin
Keyword(s):  
Front Wheel ◽  
Driving Ability ◽  
Joint Control ◽  
Test Results ◽  
Road Test ◽  
Wheel Slip ◽  
Traction Control ◽  
Wheel Drive ◽  
Driving Wheel ◽  
Independent Design

Based on the independent design front wheel drive vehicle traction control system (TCS), we finished the two kinds of working condition winter low adhesion real vehicle road test, including homogenous pavement and separate pavement straight accelerate, respectively completed the contrastive experiment with TCS and without TCS. Test results show that based on driver (AMR) and brake (BMR) joint control ASR system worked reliably, controlled effectively, being able to control excessive driving wheel slip in time, effectively improved the driving ability and handling stability of vehicle.

Kinematic Displacement Analysis of a Double-Cardan-Joint Driveline

1987 ◽  
Author(s):  
I. S. Fischer ◽  
R. N. Paul
Keyword(s):  
Phase Angle ◽  
Relative Phase ◽  
Front Wheel ◽  
Constant Input ◽  
Computer Data ◽  
Output Displacement ◽  
Wheel Drive ◽  
In Series ◽  
The Difference ◽  
Cardan Joint

Abstract The input-output displacement relations of two Cardan joints arranged in series on a driveline has been investigated in detail, including the effects of unequal joints angles, the phase angle between the two Cardan joints and also such manufacturing tolerance errors as non-rigth angle link lengths and offset joint axes. A combined Newton-Raphson and Davidson-Fletcher-Powell optimization algorithm using dual-number coordinate-transformation matrices was employed to perform the analysis. An experiment was conducted to validate the results of the analysis. The apparatus consisted of a double-Cardan-joint driveline whose rotations were measured by optical shaft encoders that were sampled by a computer data-acquisition system. The equipment was arranged so that the phase angle between the joints and the offset angles between the shafts at each of the two joints could be readily varied. The “relative phase angle”, the difference between the phase angle of the two joints and the angle between the planes defined by the input and intermediate and the intermediate and output shafts, was found to be the significant factor. If the offset angles at both Cardan joints are equal, the double-Cardan-joint driveline function as a constant-velocity coupling when the magnitude of the relative phase angle is zero. If the offset angles at the two Cardan joints are unequal, a condition prevailing in the important front-wheel-drive automobile steering column, then fluctuation in output velocity for a constant input velocity is minimized although not eliminated for zero relative phase angle.

Sign in / Sign up

Export Citation Format

Share Document