Rotor-Bearing Dynamics of High-Speed Turbomachinery

1967 ◽  
Author(s):  
B. Sternlicht
Keyword(s):  
High Speed ◽  
Rotor Bearing ◽  
Bearing Dynamics

scholarly journals Experimental research of oil-free support systems to predict the high-speed rotor bearing dynamics

2014 ◽  
Vol 3 (1) ◽  
pp. 9-16 ◽  
Author(s):  
Dorota Kozanecka ◽  
Zbigniew Kozanecki ◽  
Eliza Tkacz ◽  
Jakub Łagodziński
Keyword(s):  
Experimental Research ◽  
High Speed ◽  
Support Systems ◽  
Rotor Bearing ◽  
Bearing Dynamics

On the dynamic stability of high-speed gas bearings: stability study and experimental validation

2011 ◽  
Vol 2 (2) ◽  
pp. 342-351
Author(s):  
T. Waumans ◽  
J. Peirs ◽  
J. Reynaerts ◽  
F. Al-Bender
Keyword(s):  
Dynamic Stability ◽  
Stability Problem ◽  
High Speed ◽  
Experimental Validation ◽  
Stability Study ◽  
Gas Bearings ◽  
Aerostatic Bearings ◽  
Bearing Dynamics ◽  
Wide Operating ◽  
Operating Temperature Range

For high-speed applications, gas lubricated bearings offer very specific advantages over other,more conventional bearing technologies: a clean and oil-free solution, virtually wear-free operation, lowfrictional losses, wide operating temperature range, etc. However, the principal drawback involved in theapplication of high-speed gas bearings concerns the dynamic stability problem. Successful applicationtherefore requires control of the rotor-bearing dynamics so as to avoid instabilities.After a detailed study of the dynamic stability problem and the formulation of a convenient stability criterium,a brief overview is given of the currently existing bearing types and configurations for improving the stability.In addition, three strategies are introduced: (i) optimal design of plain aerostatic bearings; (ii) modification ofthe bearing geometry to counteract the destabilising effects in the gas film; and (iii) introduction of dampingexternal to the gas film as to compensate for the destabilising effects.These strategies are worked out into detail leading to the formulation of a series of design rules. Theireffectiveness is validated experimentally at a miniature scale. In recent experiments a rotational speed of1.2 million rpm has been achieved with a 6 mm rotor on aerodynamic journal bearings, leading to a recordDN-number of 7.2 million.

scholarly journals Model Adjustment of Small Rotors for High Speed Gas Turbines

1990 ◽  
Author(s):  
Alain Delbez ◽  
Christian Beth ◽  
Daniel Gay
Keyword(s):  
Gas Turbines ◽  
High Speed ◽  
Dynamic Behaviour ◽  
Design Stage ◽  
Rotor Bearing ◽  
Angular Velocities ◽  
Model Adjustment ◽  
Experimental Approaches

In this paper, we present the studies which are carried out at MICROTURBO relating to rotor-bearing systems mounted in small high speed gas turbines. These studies are based on both theoretical and experimental approaches, and are aimed at providing an improved prediction of the dynamic behaviour of rotors at the design stage, in particular the critical angular velocities and sensitivity to unbalance.

Vibration Signature Analysis of a Rotor Bearing System Using Response Surface Method

2009 ◽  
Author(s):  
P. K. Kankar ◽  
Satish C. Sharma ◽  
S. P. Harsha
Keyword(s):  
Response Surface ◽  
Response Surface Method ◽  
High Speed ◽  
Vibration Response ◽  
Radial Clearance ◽  
System Response ◽  
Surface Waviness ◽  
Surface Method ◽  
Rotor Bearing ◽  
Bearing System

The vibration response of a rotor bearing system is extremely important in industries and is challenged by their highly non-linear and complex properties. This paper focuses on performance prediction using response surface method (RSM), which is essential to the design of high performance rotor bearing system. Response surface method is utilized to analysis the effects of design and operating parameters on the vibration response of a rotor-bearing system. A test rig of high speed rotor supported on rolling bearings is used. Vibration response of the healthy ball bearing and ball bearings with various faults are obtained and analyzed. Distributed defects are considered as surface waviness of the bearing components. Effects of internal radial clearance and surface waviness of the bearing components and their interaction are analyzed using design of experiment (DOE) and RSM.

Hybrid composite shaft of High-Speed Rotor-Bearing System - A rotor dynamics preview

2020 ◽  
pp. 1-23
Author(s):  
Thimothy Harold Gonsalves ◽  
Mohan Kumar Garje Channabasappa ◽  
Ramesh Motagondanahalli Rangarasaiah
Keyword(s):  
Hybrid Composite ◽  
High Speed ◽  
Rotor Dynamics ◽  
System A ◽  
Composite Shaft ◽  
Rotor Bearing ◽  
Bearing System

Foil Bearings Makes Oil-Free Turbocharger Possible

2005 ◽  
Author(s):  
Crystal A. Heshmat ◽  
Hooshang Heshmat ◽  
Mark J. Valco ◽  
Kevin C. Radil ◽  
Christopher Della Corte
Keyword(s):  
High Speed ◽  
Solid Lubricant ◽  
Load Capacity ◽  
Maximum Load ◽  
Solid Lubricant Coating ◽  
Foil Bearings ◽  
Wide Range ◽  
Rotor Bearing ◽  
Component Development ◽  
Bearing System

This paper describes an oil-free, 150 Hp turbocharger that was successfully operated with compliant foil bearings in a range of pitch and roll angles, including vertical operation, thereby demonstrating its viability for aircraft applications. On a gas test stand the turbocharger was operated to 120,000 rpm, under extreme conditions. In addition, the compliant foil bearing-supported turbocharger successfully tolerated shock and vibration of 40 g. Advanced technologies have been applied to the second generation of this turbocharger, shown in Figure 1, including self acting, compliant foil hydrodynamic air bearings with advanced coatings capable, of operation above 815 °C (1500°F). Journal foil bearings with maximum load capacity up to 670 kPa (97 psi) were used in conjunction with thrust foil bearings capable of maximum loads to 570 kPa (83 psi). Bearing component development tests demonstrated 30,000 start stop cycles at 815 °C (1500°F) with a newly developed, solid lubricant coating, KOROLON™. KOROLON™ exhibits a coefficient of friction of less than 0.1 at a wide range of temperatures. Current-designed foil bearings with KOROLON™ have immensely decreased turbolag, allowing acceleration from rest to over 100,000 rpm in less than 2 seconds. Advanced bearing stiffness maintained rotor total axial end-to-end motion within 100 microns (0.004 inch). Total radial static and dynamic motion was controlled within 25 microns (0.001 inch). Development of this high speed turbomachine included bearing and solid lubricant component development tests, rotor-bearing dynamic simulator qualification and gas stand tests of the assembled turbocharger. Gas stand and simulator test results revealed stable bearing temperatures, low rotor vibrations, good shock tolerance and the ability of the rotor bearing system to sustain overspeed conditions beyond 120,000 rpm. This combination of component and integrated rotor-bearing system technology addresses many of the issues associated with application of compliant foil bearings to industrial compressors, blowers, and gas turbine engines, overcoming many of the inherently show-stopping and debilitating features of rolling element bearings, i.e., speed and temperature limitations.

Comparison of Rotordynamic Analysis Predictions With the Test Response of Simple Gas Hybrid Bearings for Oil Free Turbomachinery

2003 ◽  
Author(s):  
Deborah A. Wilde ◽  
Luis San Andre´s
Keyword(s):  
High Speed ◽  
Natural Frequencies ◽  
Damping Ratio ◽  
Rotor Speed ◽  
Gas Bearings ◽  
Model Predictions ◽  
Rotor Bearing ◽  
Frequency Ratios ◽  
Bearing System ◽  
Good Agreement

Current applications of gas film bearings in high-speed oil-free micro-turbomachinery (<0.4 MW) require calibrated predictive tools to successfully deploy their application to mass-produced systems, for example oil-free turbochargers. The present investigation details the linear rotordynamic analysis of a test rotor supported on externally pressurized gas bearings. Model predictions are compared with the test rotordynamic response determined through comprehensive experiments conducted on a small rotor supported on three lobed hybrid (hydrostatic/hydrodynamic) rigid gas bearings. Predictions for the rotor-bearing system synchronous response to imbalance show good agreement with measurements during rotor coast downs, and manifest a decrease in damping ratio as the level of external pressurization increases. The rotor-bearing eigenvalue analysis forwards natural frequencies in accordance with the measurements, and null damping ratios evidence the threshold speeds of rotordynamic instability. Estimated whirl frequency ratios are typically 50% of rotor speed, thus predicting sub synchronous instabilities at lower rotor speeds than found experimentally when increasing the magnitude of feed pressurization. Rationale asserting the nature of the discrepancies calls for further analysis.

Sign in / Sign up

Export Citation Format

Share Document