DIESEL-ENGINE DESIGN AND PERFORMANCE IN GREAT BRITAIN

1951 ◽  
Author(s):  
C.B. Dicksee
Keyword(s):  
Great Britain ◽  
Diesel Engine ◽  
Engine Design ◽  
And Performance

Emission and performance behavior of safflower oil biodiesel/diesel blends in DI diesel engine

2021 ◽  
Author(s):  
M.A. Asokan ◽  
S. Senthur Prabu ◽  
S. Prathiba ◽  
Shrey Mishra ◽  
Harsh Mittal ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Safflower Oil ◽  
Di Diesel Engine ◽  
And Performance ◽  
Performance Behavior ◽  
Emission And Performance

scholarly journals Experimental investigations on diesel engine using alumina nanoparticle fuel additive

2021 ◽  
Vol 13 (2) ◽  
pp. 168781402098840
Author(s):  
Mohammed S Gad ◽  
Sayed M Abdel Razek ◽  
PV Manu ◽  
Simon Jayaraj
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Alumina Nanoparticles ◽  
Experimental Investigations ◽  
Fuel Additive ◽  
Alumina Nanoparticle ◽  
Fuel Injectors ◽  
Performance And Emission ◽  
And Performance ◽  
The Impact

Experimental work was done to examine the impact of diesel fuel with alumina nanoparticles on combustion characteristics, emissions and performance of diesel engine. Alumina nanoparticles were mixed with crude diesel in various weight fractions of 20, 30, and 40 mg/L. The engine tests showed that nano alumina addition of 40 ppm to pure diesel led to thermal efficiency enhancement up to 5.5% related to the pure diesel fuel. The average specific fuel consumption decrease about neat diesel fuel was found to be 3.5%, 4.5%, and 5.5% at dosing levels of 20, 30, and 40 ppm, respectively at full load. Emissions of smoke, HC, CO, and NOX were found to get diminished by about 17%, 25%, 30%, and 33%, respectively with 40 ppm nano-additive about diesel operation. The smaller size of nanoparticles produce fuel stability enhancement and prevents the fuel atomization problems and the clogging in fuel injectors. The increase of alumina nanoparticle percentage in diesel fuel produced the increases in cylinder pressure, cylinder temperature, heat release rate but the decreases in ignition delay and combustion duration were shown. The concentration of 40 ppm alumina nanoparticle is recommended for achieving the optimum improvements in the engine’s combustion, performance and emission characteristics.

Emission and performance behavior of hemp seed oil biodiesel/diesel blends in DI diesel engine

2021 ◽  
Author(s):  
M.A. Asokan ◽  
S. Senthur Prabu ◽  
Anirudh Bollu ◽  
M. Abhinay Reddy ◽  
Aditya Ram ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Seed Oil ◽  
Hemp Seed ◽  
Di Diesel Engine ◽  
And Performance ◽  
Performance Behavior ◽  
Emission And Performance

Effect of altitude conditions on combustion and performance of a turbocharged direct-injection diesel engine

2021 ◽  
pp. 095440702110262
Author(s):  
Zhentao Liu ◽  
Jinlong Liu
Keyword(s):  
Diesel Engine ◽  
High Altitude ◽  
Diesel Engines ◽  
Direct Injection ◽  
Pressure Rise ◽  
Ambient Conditions ◽  
Allowable Limit ◽  
Spray Formation ◽  
Direct Injection Diesel Engine ◽  
And Performance

Market globalization necessitates the development of heavy duty diesel engines that can operate at altitudes up to 5000 m without significant performance deterioration. But the current scenario is that existing studies on high altitude effects are still not sufficient or detailed enough to take effective measures. This study applied a single cylinder direct injection diesel engine with simulated boosting pressure to investigate the performance degradation at high altitude, with the aim of adding more knowledge to the literature. Such a research engine was conducted at constant speed and injection strategy but different ambient conditions from sea level to 5000 m in altitude. The results indicated the effects of altitude on engine combustion and performance can be summarized as two aspects. First comes the extended ignition delay at high altitude, which would raise the rate of pressure rise to a point that can exceed the maximum allowable limit and therefore shorten the engine lifespan. The other disadvantage of high-altitude operation is the reduced excess air ratio and gas density inside cylinder. Worsened spray formation and mixture preparation, together with insufficient and late oxidation, would result in reduced engine efficiency, increased emissions, and power loss. The combustion and performance deteriorations were noticeable when the engine was operated above 4000 m in altitude. All these findings support the need for further fundamental investigations of in-cylinder activities of diesel engines working at plateau regions.

Diesel engine emissions and performance from blends of citrus sinensis biodiesel and diesel fuel

Fuel ◽  
2014 ◽  
Vol 132 ◽  
pp. 7-11 ◽  
Author(s):  
Gökhan Tüccar ◽  
Erdi Tosun ◽  
Tayfun Özgür ◽  
Kadir Aydın
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Citrus Sinensis ◽  
Engine Emissions ◽  
Diesel Engine Emissions ◽  
And Performance ◽  
Emissions And Performance

Modeling and performance analysis of diesel engine considering the heating effect of blow-by on cylinder intake gas

2021 ◽  
pp. 146808742110692
Author(s):  
Zhenyu Shen ◽  
Yanjun Li ◽  
Nan Xu ◽  
Baozhi Sun ◽  
Yunpeng Fu ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Engine Performance ◽  
Marine Diesel Engine ◽  
Heating Effect ◽  
Shipping Industry ◽  
Low Speed ◽  
Proposed Model ◽  
International Regulations ◽  
Marine Diesel ◽  
And Performance

Recently, the stringent international regulations on ship energy efficiency and NOx emissions from ocean-going ships make energy conservation and emission reduction be the theme of the shipping industry. Due to its fuel economy and reliability, most large commercial vessels are propelled by a low-speed two-stroke marine diesel engine, which consumes most of the fuel in the ship. In the present work, a zero-dimensional model is developed, which considers the blow-by, exhaust gas bypass, gas exchange, turbocharger, and heat transfer. Meanwhile, the model is improved by considering the heating effect of the blow-by gas on the intake gas. The proposed model is applied to a MAN B&W low-speed two-stroke marine diesel engine and validated with the engine shop test data. The simulation results are in good agreement with the experimental results. The accuracy of the model is greatly improved after considering the heating effect of blow-by gas. The model accuracy of most parameters has been improved from within 5% to within 2%, by considering the heating effect of blow-by gas. Finally, the influence of blow-by area change on engine performance is analyzed with considering and without considering the heating effect of blow-by.

Sign in / Sign up

Export Citation Format

Share Document