Numerical and Experimental Investigation into Brake Thermal Efficiency Optimum Heat Release Rate for a Diesel Engine

2019 ◽  
Author(s):  
Noboru Uchida ◽  
Jeremy GALPIN ◽  
Kazumasa Watanabe ◽  
Kenji Enya ◽  
Jean-Marc Zaccardi ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Thermal Efficiency ◽  
Brake Thermal Efficiency ◽  
Optimum Heat

A new concept of actively controlled rate of diesel combustion (ACCORDIC): Part II—simultaneous improvements in brake thermal efficiency and heat loss with modified nozzles

2018 ◽  
Vol 20 (1) ◽  
pp. 34-45 ◽  
Author(s):  
Noboru Uchida ◽  
Hiroki Watanabe
Keyword(s):  
Heat Release ◽  
Heat Loss ◽  
Heat Release Rate ◽  
Release Rate ◽  
Thermal Efficiency ◽  
Air Entrainment ◽  
Diesel Combustion ◽  
Brake Thermal Efficiency ◽  
Rate Profile ◽  
Late Part

A new diffusion-based combustion concept (named it as Actively Controlled Rate of Diesel Combustion) for the confirmation of brake thermal efficiency optimum heat release rate profile based on multiple fuel injectors has been investigated. The outstanding results are; it is possible to achieve desired heat release rate profile only by the independent control of injection timing and duration of three injectors installed to a cylinder. The optimum brake thermal efficiency was not achieved with the Otto-like cycle but with the Sabathe-like cycle as predicted by a zero-dimensional thermodynamic model. Furthermore, smoke emissions were concurrently reduced with NOx emissions by increasing fuel amount from the side injectors without any deterioration in CO and total hydrocarbon emissions. On the other hand, brake thermal efficiency itself was not so improved than expected, because of lower heat release in the late part of combustion and unexpected less heat loss reduction. To solve these issues, combustion visualization and numerical simulation analysis were carried out. The results suggested that the adjacent sprays with narrower angle from each side injector deteriorated air entrainment and mixture formation, which might also result in the deterioration in wall heat loss in the expansion stroke. To solve both issues simultaneously, modified nozzle to inject against the swirl from the side injectors was utilized and achieved an improvement in both brake thermal efficiency and heat loss. That is the interdependent and reciprocal control of in-cylinder flow and fuel injection will be one of the breakthrough technologies for current trade-offs by the temporal and spatial spray flame optimization. Furthermore, the nozzle having higher flow rate with less number of orifice was utilized for the side injectors. Even though the smoke emissions were not optimized yet, brake thermal efficiency was much improved with higher heat release rate in the late part of combustion.

Combustion and Emission Characteristics of Dual Fuel Engine for Different Parameters

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Jianjun Zhu ◽  
Peng Li ◽  
Yufeng Xie ◽  
Xin Geng
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Compression Ratio ◽  
Release Rate ◽  
Emission Characteristics ◽  
Soot Emission ◽  
Cylinder Pressure ◽  
Fuel Delivery ◽  
Soot Emissions

The effects of compression ratio and fuel delivery advance angle on the combustion and emission characteristics of premixed methanol charge induced ignition by Fischer Tropsch diesel engine were investigated using a CY25TQ diesel engine. In the process of reducing the compression ratio from 16.9 to 15.4, the starting point of combustion is fluctuating, the peak of in-cylinder pressure and the maximum pressure increase rate decrease by 44.5% and 37.7% respectively. The peak instantaneous heat release rate increases by 54.4%. HC and CO emissions are on a rising trend. NOx and soot emissions were greatly decreased. The soot emission has the biggest drop of 50%. Reducing the fuel delivery advance angle will make the peak of in-cylinder pressure and the peak of pressure rise rate increase while the peak of heat release rate decreases. The soot emission is negatively correlated with the fuel delivery advance angle. When the fuel delivery advance angle is 16° CA, the soot emissions increased the most by 130%.

Combustion Characteristics of Single Cylinder Diesel Engine Fueled with Blends of Thumba Biodiesel as an Alternative Fuel

2019 ◽  
Vol 969 ◽  
pp. 451-460
Author(s):  
Manpreet Singh ◽  
Mohd Yunus Sheikh ◽  
Dharmendra Singh ◽  
P. Nageswara Rao
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Diesel Fuel ◽  
Release Rate ◽  
Mass Fraction ◽  
Pressure Rise ◽  
Cylinder Pressure ◽  
Gas Temperature ◽  
Edible Vegetable Oil

The rapid rise in energy requirement and problem regarding atmosphere pollutions, renewable biofuels are the better alternative choice for the internal combustion engine to partially or totally replace the pollutant petroleum fuel. In the present work, thumba (Citrullus colocynthis) non-edible vegetable oil is used for the production of biodiesel and examine its possibility as diesel engine fuel. Transesterification process is used to produce biodiesel from thumba non-edible vegetable oil. Thumba biodiesel (TBD) is used to prepare five different volume concentration (blends) with neat diesel (D100), such as TBD5, TBD15, TBD25, TBD35 and TBD45 to run a single cylinder diesel engine. The diesel engine's combustion parameter such as in-cylinder pressure, rate of pressure rise, net heat release rate, cumulative heat release, mean gas temperature, and mass fraction burnt analyzed through graphs and compared all thumba biodiesel blends result with neat diesel fuel. The mass fraction burnt start earlier for thumba biodiesel blends compared to diesel fuel because of less ignition delay while peak in-cylinder pressure, maximum rate of pressure rise, maximum net heat release rate, maximum cumulative heat release, and maximum mean gas temperature has found decreased results up to 1.93%, 5.53%, 4.11%, 4.65%, and 1.73% respectively for thumba biodiesel.

Determination of the Start and End of Combustion in a Direct Injection Diesel Engine Using the Apparent Heat Release Rate

2017 ◽  
Author(s):  
Joseph Gerard T. Reyes ◽  
Edwin N. Quiros
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Direct Injection ◽  
Injection Timing ◽  
Fuel Injector ◽  
Direct Injection Diesel Engine ◽  
Crank Angle ◽  
Start Of Combustion

The combustion duration in an internal combustion engine is the period bounded by the engine crank angles known as the start of combustion (SOC) and end of combustion (EOC), respectively. This period is essential in analysis of combustion for the such as the production of exhaust emissions. For compression-ignition engines, such as diesel engines, several approaches were developed in order to approximate the crank angle for the start of combustion. These approaches utilized the curves of measured in-cylinder pressures and determining by inspection the crank angle where the slope is steep following a minimum value, indicating that combustion has begun. These pressure data may also be utilized together with the corresponding cylinder volumes to generate the apparent heat release rate (AHRR), which shows the trend of heat transfer of the gases enclosed in the engine cylinder. The start of combustion is then determined at the point where the value of the AHRR is minimum and followed by a rapid increase in value, whereas the EOC is at the crank angle where the AHRR attains a flat slope prior to the exhaust stroke of the engine. To verify the location of the SOC, injection line pressures and fuel injection timing are also used. This method was applied in an engine test bench using a four-cylinder common-rail direct injection diesel engine with a pressure transducer installed in the first cylinder. Injector line pressures and fuel injector voltage signals per engine cycle were also recorded and plotted. By analyzing the trends of this curves in line with the generated AHRR curves, the SOC may be readily determined.

Development of Diesel Engine Emissions Control Models Based on Heat Release Rate Analysis of Combustion Processes

2011 ◽  
Author(s):  
Dong Wang ◽  
Chao Zhang
Keyword(s):  
Diesel Engine ◽  
Numerical Simulations ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Control Model ◽  
Premixed Combustion ◽  
Linear Control ◽  
Control Models ◽  
Nox Control

Linear control models to control the Nitrogen Oxides (NOx) and soot emissions from a diesel engine were developed through numerical simulations. A modified KIVA-3V code was used to calculate the NOx and soot formations in a direct injection diesel engine under different operating conditions. The following relationships between the pollutant formations and the heat release rate were observed: 1) NOx formation amount is related to the peak value of the heat release rate and the timing of the premixed combustion; 2) soot formation amount is related to the peak heat release rate and the soot oxidation amount is related to the timing of the premixed combustion. Based on the above observations, linear control models for NOx and soot emissions were constructed. The NOx control model developed through the numerical simulations was implemented into the controller of an EGR valve on a small diesel engine. The experimental results showed that the NOx control model was effective in reducing NOx emissions under high RPM conditions.

Sign in / Sign up

Export Citation Format

Share Document