Wall Heat Transfer Modeling Based on the Energy Equation For Zero Dimensional Engine Simulation

2019 ◽  
Author(s):  
Yuji Harada ◽  
Kenji Uchida ◽  
Hiroyuki Yamashita
Keyword(s):  
Heat Transfer ◽  
Energy Equation ◽  
Wall Heat Transfer ◽  
Heat Transfer Modeling ◽  
Engine Simulation

Heat transfer modeling and identification using fractional order state space models

2008 ◽  
Vol 42 (6-8) ◽  
pp. 939-951 ◽  
Author(s):  
Tounsia Jamah ◽  
Rachid Mansouri ◽  
Saïd Djennoune ◽  
Maâmar Bettayeb
Keyword(s):  
Heat Transfer ◽  
State Space ◽  
Fractional Order ◽  
State Space Models ◽  
Heat Transfer Modeling ◽  
Order State

Experimental investigation of wall heat transfer due to spray combustion in a high-pressure/high-temperature vessel

2021 ◽  
pp. 146808742110072
Author(s):  
Karri Keskinen ◽  
Walter Vera-Tudela ◽  
Yuri M Wright ◽  
Konstantinos Boulouchos
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
High Pressure ◽  
High Temperature ◽  
High Speed ◽  
Transfer Problem ◽  
Wall Heat Transfer ◽  
Gas Temperature ◽  
Reference Case ◽  
High Pressure High Temperature

Combustion chamber wall heat transfer is a major contributor to efficiency losses in diesel engines. In this context, thermal swing materials (adapting to the surrounding gas temperature) have been pinpointed as a promising mitigative solution. In this study, experiments are carried out in a high-pressure/high-temperature vessel to (a) characterise the wall heat transfer process ensuing from wall impingement of a combusting fuel spray, and (b) evaluate insulative improvements provided by a coating that promotes thermal swing. The baseline experimental condition resembles that of Spray A from the Engine Combustion Network, while additional variations are generated by modifying the ambient temperature as well as the injection pressure and duration. Wall heat transfer and wall temperature measurements are time-resolved and accompanied by concurrent high-speed imaging of natural luminosity. An investigation with an uncoated wall is carried out with several sensor locations around the stagnation point, elucidating sensor-to-sensor variability and setup symmetry. Surface heat flux follows three phases: (i) an initial peak, (ii) a slightly lower plateau dependent on the injection duration, and (iii) a slow decline. In addition to the uncoated reference case, the investigation involves a coating made of porous zirconia, an established thermal swing material. With a coated setup, the projection of surface quantities (heat flux and temperature) from the immersed measurement location requires additional numerical analysis of conjugate heat transfer. Starting from the traces measured beneath the coating, the surface quantities are obtained by solving a one-dimensional inverse heat transfer problem. The present measurements are complemented by CFD simulations supplemented with recent rough-wall models. The surface roughness of the coated specimen is indicated to have a significant impact on the wall heat flux, offsetting the expected benefit from the thermal swing material.

Data-driven reduced order modeling based on tensor decompositions and its application to air-wall heat transfer in buildings

SeMA Journal ◽  
2021 ◽  
Author(s):  
M. Azaïez ◽  
T. Chacón Rebollo ◽  
M. Gómez Mármol ◽  
E. Perracchione ◽  
A. Rincón Casado ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Reduced Order Modeling ◽  
Data Driven ◽  
Wall Heat Transfer ◽  
Reduced Order ◽  
Tensor Decompositions

Heat transfer modeling of multilayer reactive foil

2011 ◽  
Vol 8 (2) ◽  
pp. 151-157 ◽  
Author(s):  
R. Liu ◽  
S. Guo ◽  
X. Qiu ◽  
J. Wang
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Modeling
Sign in / Sign up

Export Citation Format

Share Document