Investigation of the High-Pressure-Dual-Fuel (HPDF) combustion process of natural gas on a fully optically accessible research engine

2019 ◽  
Author(s):  
Stephan Gleis ◽  
Stephanie Frankl ◽  
Dominik Waligorski ◽  
Dr.-Ing. Maximilian Prager ◽  
Prof. Dr.-Ing. Georg Wachtmeister
Keyword(s):  
High Pressure ◽  
Natural Gas ◽  
Combustion Process ◽  
Dual Fuel

scholarly journals A Numerical Study on the Combustion Process and Emission Characteristics of a Natural Gas-Diesel Dual-Fuel Marine Engine at Full Load

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1342
Author(s):  
Van Chien Pham ◽  
Jae-Hyuk Choi ◽  
Beom-Seok Rho ◽  
Jun-Soo Kim ◽  
Kyunam Park ◽  
...  
Keyword(s):  
Natural Gas ◽  
Combustion Process ◽  
Simulation Software ◽  
Dual Fuel ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Cylinder Pressure ◽  
Marine Engine ◽  
Full Load ◽  
Simulation Results

This paper presents research on the combustion and emission characteristics of a four-stroke Natural gas–Diesel dual-fuel marine engine at full load. The AVL FIRE R2018a (AVL List GmbH, Graz, Austria) simulation software was used to conduct three-dimensional simulations of the combustion process and emission formations inside the engine cylinder in both diesel and dual-fuel mode to analyze the in-cylinder pressure, temperature, and emission characteristics. The simulation results were then compared and showed a good agreement with the measured values reported in the engine’s shop test technical data. The simulation results showed reductions in the in-cylinder pressure and temperature peaks by 1.7% and 6.75%, while NO, soot, CO, and CO2 emissions were reduced up to 96%, 96%, 86%, and 15.9%, respectively, in the dual-fuel mode in comparison with the diesel mode. The results also show better and more uniform combustion at the late stage of the combustions inside the cylinder when operating the engine in the dual-fuel mode. Analyzing the emission characteristics and the engine performance when the injection timing varies shows that, operating the engine in the dual-fuel mode with an injection timing of 12 crank angle degrees before the top dead center is the best solution to reduce emissions while keeping the optimal engine power.

Simulation Research on Combustion Process in a Natural Gas-Diesel Dual-Fuel Marine Engine

2014 ◽  
Vol 525 ◽  
pp. 227-231 ◽  
Author(s):  
Min Xiao ◽  
Chun Long Feng
Keyword(s):  
Natural Gas ◽  
Total Energy ◽  
Combustion Process ◽  
Power Reduction ◽  
Dual Fuel ◽  
Injection Timing ◽  
Simulation Research ◽  
Injection Duration ◽  
Medium Speed ◽  
The Right

In order to solve the problem of Diesel natural gas dual fuel engine, such as power reduction, low charging efficiency, the conception of diesel engine fueled with pilot-ignited directly-injected liquefied natural gas is put forward. On the basis of this theory, a medium speed diesel of the marine is refitted into dual fuel engine, in order to keep original power, decrease the temperature of combustion and reduce emission. The LNG injection timing, duration of LNG injection and the different ratios the pilot diesel to total energy are studied the method of AVL FIRE software. Conclusions are as follows: When the different ratios pilot diesel to total energy is 0.5%, the engine can not work; Delaying the LNG injection timing, shortening the LNG injection duration and choose the right ratios pilot diesel to total energy can reach the indicated power of original machine, and the NOx emissions level will be greatly reduced.

scholarly journals Numerical Analysis of High-Pressure Direct Injection Dual-Fuel Diesel-Liquefied Natural Gas (LNG) Engines

Processes ◽  
2020 ◽  
Vol 8 (3) ◽  
pp. 261 ◽  
Author(s):  
Alberto Boretti
Keyword(s):  
High Pressure ◽  
Steady State ◽  
Liquid Phase ◽  
Natural Gas ◽  
Power Density ◽  
Conversion Efficiency ◽  
Liquefied Natural Gas ◽  
Dual Fuel ◽  
Fuel Conversion ◽  
Better Than

Dual fuel engines using diesel and fuels that are gaseous at normal conditions are receiving increasing attention. They permit to achieve the same (or better) than diesel power density and efficiency, steady-state, and substantially similar transient performances. They also permit to deliver better than diesel engine-out emissions for CO2, as well as particulate matter, unburned hydrocarbons, and nitrous oxides. The adoption of injection in the liquid phase permits to further improve the power density as well as the fuel conversion efficiency. Here, a model is developed to study a high-pressure, 1600 bar, liquid phase injector for liquefied natural gas (LNG) in a high compression ratio, high boost engine. The engine features two direct injectors per cylinder, one for the diesel and one for the LNG. The engine also uses mechanically assisted turbocharging (super-turbocharging) to improve the steady-state and transient performances of the engine, decoupling the power supply at the turbine from the power demand at the compressor. Results of steady-state simulations show the ability of the engine to deliver top fuel conversion efficiency, above 48%, and high efficiencies, above 40% over the most part of the engine load and speed range. The novelty of this work is the opportunity to use very high pressure (1600 bar) LNG injection in a dual fuel diesel-LNG engine. It is shown that this high pressure permits to increase the flow rate per unit area; thus, permitting smaller and lighter injectors, of faster actuation, for enhanced injector-shaping capabilities. Without fully exploring the many opportunities to shape the heat release rate curve, simulations suggest two-point improvements in fuel conversion efficiency by increasing the injection pressure.

Numerical Simulation of a Large Bore Dual Fuel Marine Engine Using Tabulated Detailed Reaction Mechanisms

2019 ◽  
Author(s):  
Sascha Andree ◽  
Dmitry Goryntsev ◽  
Martin Theile ◽  
Björn Henke ◽  
Karsten Schleef ◽  
...  
Keyword(s):  
Reaction Mechanism ◽  
Natural Gas ◽  
Chemical Reaction ◽  
Reaction Mechanisms ◽  
Combustion Process ◽  
Fuel Combustion ◽  
Dual Fuel ◽  
Start Of Injection ◽  
Flamelet Generated Manifold ◽  
Dual Fuel Combustion

Abstract The simulation of a diesel natural gas dual fuel combustion process is the topic of this paper. Based on a detailed chemical reaction mechanism, which was applied for such a dual fuel combustion, the complete internal combustion engine process was simulated. Two single fuel combustion reaction mechanisms from literature were merged, to consider the simultaneous reaction paths of diesel and natural gas. N-heptane was chosen as a surrogate for diesel. The chemical reaction mechanisms are solved by applying a tabulation method using the software tool AVL Tabkin™. In combination with a Flamelet Generated Manifold (FGM) combustion model, this leads to a reduction of computational effort compared to a direct solving of the reaction mechanism, because of a decoupling of chemistry and flow calculations. Turbulence was modelled using an unsteady Reynolds-Averaged Navier Stokes (URANS) model. In comparison to conventional combustion models, this approach allows for detailed investigations of the complex ignition process of the dual fuel combustion process. The unexpected inversely proportional relationship between start of injection (SOI) and start of combustion (SOC), a later start of injection makes for an earlier combustion of the main load, is only one of these interesting combustion phenomena, which can now be analyzed in detail. Further investigations are done for different engine load points and multiple pilot injection strategies. The simulation results are confirmed by experimental measurements at a medium speed dual fuel single cylinder research engine.

Investigation of ammonia and hydrogen as CO2-free fuels for heavy duty engines using a high pressure dual fuel combustion process

2020 ◽  
pp. 146808742096787
Author(s):  
Stephanie Frankl ◽  
Stephan Gleis ◽  
Stephan Karmann ◽  
Maximilian Prager ◽  
Georg Wachtmeister
Keyword(s):  
High Pressure ◽  
High Pressures ◽  
Numerical Study ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Dual Fuel ◽  
Parameter Study ◽  
Fuel Injector ◽  
Cfd Model ◽  
Pilot Fuel

This work is a numerical study of the use of ammonia and hydrogen in a high-pressure-dual-fuel (HPDF) combustion. The main fuels (hydrogen and ammonia) are direct injected and ignited by a small amount of direct injected pilot fuel. The fuels are injected using a dual fuel injector from Woodward L’Orange, which can induce two fuels independently at high pressures up to 1800 bar for the pilot fuel and maximum 500 bar for the main. The numerical CFD-model gets validated for of hydrogen-HPDF with experimental data. Due to safety issues at the test rig it was not possible to use ammonia in the experiments, so it is modelled using the numerical model. It is assumed that the CFD-model also gives qualitative correct results for the use of ammonia as main fuel, so a parameter study of ammonia-HPDF is made. The results for the hydrogen-HPDF show, that hydrogen can be used in the engine without any further modifications. The combustion is very stable, and the hydrogen ignites almost immediately when it enters the combustion chamber. The results of the ammonia combustion indicate, that the HPDF combustion mode can handle ammonia effectively. It seems beneficial to inject the ammonia at higher pressures than hydrogen. Also pre-heating the ammonia can increase the combustion efficiency.

scholarly journals Use of Adaptive Injection Strategies to Increase the Full Load Limit of RCCI Operation

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Reed Hanson ◽  
Andrew Ickes ◽  
Thomas Wallner
Keyword(s):  
Natural Gas ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Experimental Testing ◽  
Peak Load ◽  
Combustion Process ◽  
Pressure Rise ◽  
Dual Fuel ◽  
The Impact ◽  
Injection Strategies

Dual-fuel combustion using port-injection of low reactivity fuel combined with direct injection (DI) of a higher reactivity fuel, otherwise known as reactivity controlled compression ignition (RCCI), has been shown as a method to achieve low-temperature combustion with moderate peak pressure rise rates, low engine-out soot and NOx emissions, and high indicated thermal efficiency. A key requirement for extending to high-load operation is moderating the reactivity of the premixed charge prior to the diesel injection. One way to accomplish this is to use a very low reactivity fuel such as natural gas. In this work, experimental testing was conducted on a 13 l multicylinder heavy-duty diesel engine modified to operate using RCCI combustion with port injection of natural gas and DI of diesel fuel. Engine testing was conducted at an engine speed of 1200 rpm over a wide variety of loads and injection conditions. The impact on dual-fuel engine performance and emissions with respect to varying the fuel injection parameters is quantified within this study. The injection strategies used in the work were found to affect the combustion process in similar ways to both conventional diesel combustion (CDC) and RCCI combustion for phasing control and emissions performance. As the load is increased, the port fuel injection (PFI) quantity was reduced to keep peak cylinder pressure (PCP) and maximum pressure rise rate (MPRR) under the imposed limits. Overall, the peak load using the new injection strategy was shown to reach 22 bar brake mean effective pressure (BMEP) with a peak brake thermal efficiency (BTE) of 47.6%.

scholarly journals EFFECT OF CNG IN A FUEL DOSE ON THE COMBUSTION PROCESS OF A COMPRESSION-IGNITION ENGINE

Transport ◽  
2015 ◽  
Vol 30 (2) ◽  
pp. 162-171 ◽  
Author(s):  
Maciej Mikulski ◽  
Sławomir Wierzbicki
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Alternative Fuels ◽  
Combustion Process ◽  
Diesel Oil ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Compression Ignition Engines ◽  
Main Component

Currently, one of the major trends in the research of contemporary combustion engines involves the potential use of alternative fuels. Considerable attention has been devoted to methane, which is the main component of Natural Gas (NG) and can also be obtained by purification of biogas. In compression-ignition engines fired with methane or Compressed Natural Gas (CNG), it is necessary to apply a dual-fuel feeding system. This paper presents the effect of the proportion of CNG in a fuel dose on the process of combustion. The recorded time series of pressure in a combustion chamber was used to determine the repeatability of the combustion process and the change of fuel compression-ignition delay in the combustion chamber. It has been showed that NG does not burn completely in a dual-fuel engine. The best conditions for combustion are ensured with higher concentrations of gaseous fuel. NG ignition does not take place simultaneously with diesel oil ignition. Moreover, if a divided dose of diesel is injected, NG ignition probably takes place at two points, as diesel oil.

Sign in / Sign up

Export Citation Format

Share Document