Lumped Parameter Transient Thermal Model of Motor Considering Temperature and Flow Rate of Cooling Water

2019 ◽  
Author(s):  
Juncheng Li ◽  
Jimin Ni ◽  
XiaoChuan Xu
Keyword(s):  
Flow Rate ◽  
Thermal Model ◽  
Cooling Water ◽  
Lumped Parameter ◽  
Rate Of Cooling ◽  
Transient Thermal

Hydraulic model of a water cooling system in a chemical plant

1988 ◽  
Vol 53 (4) ◽  
pp. 788-806
Author(s):  
Miloslav Hošťálek ◽  
Jiří Výborný ◽  
František Madron
Keyword(s):  
Flow Rate ◽  
Cooling System ◽  
Cooling Water ◽  
Graph Algorithm ◽  
Automatic Generation ◽  
Hydraulic Calculation ◽  
Return Flow ◽  
Flow Rates ◽  
Pressure Losses ◽  
Controlled Flow

Steady state hydraulic calculation has been described of an extensive pipeline network based on a new graph algorithm for setting up and decomposition of balance equations of the model. The parameters of the model are characteristics of individual sections of the network (pumps, pipes, and heat exchangers with armatures). In case of sections with controlled flow rate (variable characteristic), or sections with measured flow rate, the flow rates are direct inputs. The interactions of the network with the surroundings are accounted for by appropriate sources and sinks of individual nodes. The result of the calculation is the knowledge of all flow rates and pressure losses in the network. Automatic generation of the model equations utilizes an efficient (vector) fixing of the network topology and predominantly logical, not numerical operations based on the graph theory. The calculation proper utilizes a modification of the model by the method of linearization of characteristics, while the properties of the modified set of equations permit further decrease of the requirements on the computer. The described approach is suitable for the solution of practical problems even on lower category personal computers. The calculations are illustrated on an example of a simple network with uncontrolled and controlled flow rates of cooling water while one of the sections of the network is also a gravitational return flow of the cooling water.

Surge in a Low-Speed Radial Compressor

1998 ◽  
Author(s):  
Corine Meuleman ◽  
Frank Willems ◽  
Rick de Lange ◽  
Bram de Jager
Keyword(s):  
Flow Rate ◽  
Pressure Rise ◽  
Flow Coefficient ◽  
Lumped Parameter Model ◽  
Pressure Oscillations ◽  
Vaned Diffuser ◽  
Flow Angle ◽  
Radial Compressor ◽  
Low Speed ◽  
Lumped Parameter

Surge is measured in a low-speed radial compressor with a vaned diffuser. For this system, the flow coefficient at surge is determined. This coefficient is a measure for the inducer inlet flow angle and is found to increase with increasing rotational speed. Moreover, the frequency and amplitude of the pressure oscillations during fully-developed surge are compared with results obtained with the Greitzer lumped parameter model. The measured surge frequency increases when the compressor mass flow is throttled to a smaller flow rate. Simulations show that the Greitzer model describes this relation reasonably well except for low rotational speeds. The predicted amplitude of the pressure rise oscillations is approximately two times too small when deep surge is met in the simulations. For classic surge, the agreement is worse. The amplitude is found to depend strongly on the shape of the compressor and throttle characteristic, which are not accurately known.

A lumped-parameter electro-thermal model for cylindrical batteries

2014 ◽  
Vol 257 ◽  
pp. 1-11 ◽  
Author(s):  
Xinfan Lin ◽  
Hector E. Perez ◽  
Shankar Mohan ◽  
Jason B. Siegel ◽  
Anna G. Stefanopoulou ◽  
...  
Keyword(s):  
Thermal Model ◽  
Lumped Parameter

scholarly journals Measurements and Computations of Internal Temperatures of the IGBT and the Diode Situated in the Common Case

Electronics ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 210
Author(s):  
Paweł Górecki ◽  
Krzysztof Górecki
Keyword(s):  
Thermal Properties ◽  
Measurement Error ◽  
Thermal Model ◽  
Bipolar Transistor ◽  
Internal Temperature ◽  
Self Heating ◽  
Factors Influencing ◽  
Proposed Model ◽  
The Common ◽  
Transient Thermal

This article proposes effective methods of measurements and computations of internal temperature of the dies of the Insulted Gate Bipolar Transistor (IGBT) and the diode mounted in the common case. The nonlinear compact thermal model of the considered device is proposed. This model takes into account both self-heating phenomena in both dies and mutual thermal couplings between them. In the proposed model, the influence of the device internal temperature on self and transfer thermal resistances is taken into account. Methods of measurements of each self and transfer transient thermal impedances occurring in this model are described and factors influencing the measurement error of these methods are analysed. Some results illustrating thermal properties of the investigated devices including the IGBT and the antiparallel diode in the common case are shown and discussed. Computations illustrating the usefulness of the proposed compact thermal model are presented and compared to the results of measurements. It is proved that differences between internal temperature of both dies included in the TO-247 case can exceed even 15 K.

A New Transient Thermal Model for Predicting Cooling Temperature and Cooldown Time of a Subsea Pipe-in-Pipe Flowline System Transporting Waxy Hydrocarbons

2021 ◽  
Author(s):  
Keshawa Shukla
Keyword(s):  
Analytical Model ◽  
Production System ◽  
Thermal Model ◽  
Hydrate Formation ◽  
Pipe Production ◽  
Fluid Temperature ◽  
Waxy Crude Oil ◽  
Cooling Temperature ◽  
Fluid Properties ◽  
Transient Thermal

Abstract The proper understanding of cooling temperature and cooldown time for the operation of a subsea system producing hydrocarbons from the reservoir to the host facility is one of the important flow assurance issues for managing heat retention in the production system due to solids formation and their deposition. In this paper, an analytical transient thermal model is developed for determining the cooling temperature and cooldown time for shut-in operations of a subsea pipe-in-pipe production system, transporting waxy crude oil from the reservoir to the host facility. Here, the cooldown time is defined as the time when the fluid temperature approaches the wax appearance temperature before reaching the hydrate formation temperature during any shut-in operations. The analytical model builds upon an inhomogeneous transient method incorporating an internal temperature gradient. The model results are benchmarked against the commercial OLGA simulation results for a few selected deepwater pipe-in-pipe flowline configuration. The model predictions resemble well with OLGA results over a range of conditions. The analytical model could optimize dry insulation and cooldown time requirements efficiently for the assumed PIP flowline configurations and fluid properties under any subsea environments.

Sign in / Sign up

Export Citation Format

Share Document