Structural Concept of an Adaptive Shock Control Bump Spoiler

2017 ◽  
Author(s):  
Markus Kintscher ◽  
Hans Peter Monner
Keyword(s):  
Shock Control Bump ◽  
Shock Control ◽  
Structural Concept

scholarly journals Structural concept of an adaptive shock control bump spoiler

2021 ◽  
Author(s):  
Markus Kintscher ◽  
Johannes Riemenschneider ◽  
Hans-Peter Monner ◽  
Martin Wiedemann
Keyword(s):  
Applied Sciences ◽  
Laminar Flow ◽  
Drag Reduction ◽  
Computational Methods ◽  
Leading Edge ◽  
High Lift ◽  
Shock Control Bump ◽  
Shock Control ◽  
European Congress ◽  
Structural Concept

AbstractDrag reduction technologies in aircraft design are the key enabler for reducing emissions and for sustainable growth of commercial aviation. Laminar wing technologies promise a significant benefit by drag reduction and are, therefore, under investigation in various European projects. However, of the established moveable concepts and high-lift systems thus far most do not cope with the requirements for natural laminar flow wings. To this aim, new leading edge high-lift systems have been the focus of research activities in the last 5 years. Such leading edge devices investigated in projects include a laminar flow-compatible Kruger flap (Schlipf (2011) Insect shielding Krüger—structural design for a laminar flow wing. In: DGLR Congress 2011, Bremen, pp 55–60) and the Droop Nose concept (Kintscher et al. Ground testof an enhanced adaptive droop nose device. In: European Congress on Computational Methods in Applied Sciences and Engineering, ECCOMAS 2016. ECCOMAS2016—VII European Congress on Computational Methods in Applied Sciences and Engineering, 5–10 June 2016, Crete Island, Greece; Kintscher et al. Low speed wind tunnel test of a morphing leading edge. In: AIDAA—Italian Association of Aeronautics and Astronautics XXII Conference, 09–12 Sept. 2013. Neapel, Italien) and these can be considered as alternatives to the conventional slat. Hybrid laminar flow concepts are also under investigation at several research institutes in Europe (Fischer. Stepless and sustainable research for the aircraft of tomorrow—from AFloNext to Clean Sky 2. In: 1st AFloNext Workshop Key Note Lecture No. 1, Delft, The Netherlands, 10 Sept 2015). Another challenge associated with laminar wings aside from the development of leading edge movables is the need to address the control of aerodynamic shocks and buffeting as laminar wings are sensitive to high flow speeds. Here, one possible method of decreasing the wave drag caused by the aerodynamic shock is through the use of shock control bumps (SCBs). The objective of SCBs is the conversion of a single strong shock into several smaller and weaker λ-shocks resulting in a drag benefit when deployed correctly. A particular desirable characteristic of SCBs is that they should be adaptable in position and height as the shock position changes with varying conditions such as speed, altitude, and angle of attack during the flight. However, as a fixed case, SCBs can also help to control laminar buffeting by fixing the shock into given positions at the SCBs location. In this paper, a structural concept for an adaptive shock control bump spoiler is presented. Based on a concept of a fixed bump SCB spoiler, a design for an adaptive spoiler with two conventional actuators is presented. Design drivers and interdependencies of important design parameters are discussed. The presented design is simple and aims for a high TRL without adding much complexity to the spoiler. It is robust and able to form a bump with a height of 0.6% chord length which position can be adapted in a range of 10% chord. This paper is a follow-up of a previous publication (Kintscher and Monner, SAE Tech Paper 10.4271/2017-01-2164, 2017) with extending the focus by a validation of computational results by experimental tests.

scholarly journals Unsteady Simulation of Transonic Buffet of a Supercritical Airfoil with Shock Control Bump

Aerospace ◽  
2021 ◽  
Vol 8 (8) ◽  
pp. 203
Author(s):  
Yufei Zhang ◽  
Pu Yang ◽  
Runze Li ◽  
Haixin Chen
Keyword(s):  
Lift Coefficient ◽  
Pressure Coefficient ◽  
Flow Characteristics ◽  
Control Effect ◽  
Shock Control Bump ◽  
Shock Control ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Unsteady Simulation ◽  
Drag Ratio

The unsteady flow characteristics of a supercritical OAT15A airfoil with a shock control bump were numerically studied by a wall-modeled large eddy simulation. The numerical method was first validated by the buffet and nonbuffet cases of the baseline OAT15A airfoil. Both the pressure coefficient and velocity fluctuation coincided well with the experimental data. Then, four different shock control bumps were numerically tested. A bump of height h/c = 0.008 and location xB/c = 0.55 demonstrated a good buffet control effect. The lift-to-drag ratio of the buffet case was increased by 5.9%, and the root mean square of the lift coefficient fluctuation was decreased by 67.6%. Detailed time-averaged flow quantities and instantaneous flow fields were analyzed to demonstrate the flow phenomenon of the shock control bumps. The results demonstrate that an appropriate “λ” shockwave pattern caused by the bump is important for the flow control effect.

Robust active shock control bump design optimisation using hybrid parallel MOGA

2013 ◽  
Vol 80 ◽  
pp. 214-224 ◽  
Author(s):  
D.S. Lee ◽  
G. Bugeda ◽  
J. Periaux ◽  
E. Onate
Keyword(s):  
Design Optimisation ◽  
Shock Control Bump ◽  
Shock Control

Numerical analysis on shape memory alloy–based adaptive shock control bump

2018 ◽  
Vol 29 (15) ◽  
pp. 3055-3066 ◽  
Author(s):  
Lin Hao ◽  
Jinhao Qiu ◽  
Hongli Ji ◽  
Rui Nie
Keyword(s):  
Shape Memory Alloy ◽  
Shape Memory ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Wave Drag ◽  
Initial Shape ◽  
Thermally Activated ◽  
Bump Height ◽  
Shock Control Bump ◽  
Shock Control

A three-dimensional adaptive shock control bump made of shape memory alloy is proposed for transonic wings. The methodology to adaptively change the configuration of the airfoil using the shape memory alloy bump to reduce the shock strength and wave drag is numerically demonstrated using an airfoil RAE2822. The shape memory alloy bump is trained to have a flat initial shape with certain initial strain and can swell up when thermally activated. Boyd–Lagoudas phenomenological model is implemented in finite element method and used to compute the two-dimensional profile and the height of the shape memory alloy bump during thermal activation. The results show that the shape memory alloy bump can generate a considerable deflection due to the reverse phase transformation when thermally activated. The dependence of aerodynamic characteristics of the wing on the height of the shape memory alloy bump and the angle of attack is investigated using computational fluid dynamics method. The results show that there is an optimal bump height for a given angle of attack and the bump with a given height is effective only in certain range of angle of attack. Optimization of bump height and the corresponding driving temperature are carried out under variable angles of attack with the lift-to-drag ratio as the objective function.

Sign in / Sign up

Export Citation Format

Share Document