The Dual Phase Twin Synchronous Belt Drive

2017 ◽  
Author(s):  
Jing Yuan
Keyword(s):  
Belt Drive ◽  
Dual Phase ◽  
Synchronous Belt Drive

scholarly journals Research and Test of Three-Pulley Noncircular Synchronous Pulley Transmission Mechanism with Minimum Slack

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Jianneng Chen ◽  
Xincheng Sun ◽  
Chuanyu Wu ◽  
Dadu Xiao ◽  
Jun Ye
Keyword(s):  
Optimization Design ◽  
Simulation Analysis ◽  
Transmission Mechanism ◽  
Driving Mechanism ◽  
Belt Drive ◽  
Drive Mechanism ◽  
Automatic Optimization ◽  
Pitch Curve ◽  
Synchronous Belt Drive ◽  
Belt Transmission

AbstractThe noncircular synchronous belt drive mechanism has demonstrated certain achievements and has been used in special fields. Research regarding noncircular synchronous belt drive mechanisms has focused on optimization design and kinematic analysis in China, whereas two pulley noncircular synchronous belt transmissions have been developed overseas. However, owing to the noncircular characteristics of the belt pulley, the real-time variation in the belt length slack during the transmission of the noncircular synchronous belt is significant, resulting in high probabilities of skipping and vibration. In this study, a noncircular tensioning pulley is added to create a stable three-pulley noncircular synchronous belt driving mechanism and a good synchronous belt tensioning, with no skipping; hence, the non-uniform output characteristic of the driven pulley is consistent with the theoretical value. In the circular noncircular noncircular three-pulley noncircular synchronous belt mechanism, the pitch curve of the driving synchronous belt pulley is circular, whereas those of the driven synchronous belt and tensioning pulleys are noncircular. To minimize the slack of the belt length of the synchronous belt and the constraint of the concavity and circumference of the tensioning pulley, an automatic optimization model of the tensioning pulley pitch curve is established. The motion simulation, analysis, and optimization code for a three-belt-pulley noncircular synchronous belt drive mechanism is written, and the variation in belt length slack under different speed ratios is analyzed based on several examples. The testbed for a circular–noncircular–noncircular three-pulley noncircular synchronous belt transmission mechanism is developed. The test shows that the three-pulley noncircular synchronous belt drives well. This study proposes an automatic optimization algorithm for the tensioning pulley pitch curve of a noncircular synchronous belt transmission mechanism; it yields a stable transmission of the noncircular synchronous belt transmission mechanism as well as non-uniform output characteristics.

Development and Application of a Synchronous Belt Drive Design System

2014 ◽  
Vol 971-973 ◽  
pp. 450-453 ◽  
Author(s):  
Yi Guo ◽  
Guo Liang Ding ◽  
Zhi Qiang Li
Keyword(s):  
3D Modeling ◽  
Spare Parts ◽  
Design System ◽  
Belt Drive ◽  
Design Calculation ◽  
Accurate Design ◽  
Basic Language ◽  
Synchronous Belt Drive ◽  
Visual Basic Language ◽  
User Friendly

To solve the synchronous belt drive design and 3D modeling problem, a synchronous belt drive design system has been developed with the Visual Basic language and SolidWorks platform. Applications have shown that this system can realize design calculation of the synchronous belt drive and the 3D modeling of spare parts and assemblies like the small belt pulley, large belt pulley and synchronous belt, as required by the customer. Also, it has a user-friendly interface, handy operation, simple operation, and accurate design results, to effectively shorten the design period.

Transmission Error Due to Resonance in Synchronous Belt Drive With Eccentric Pulley

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Masanori Kagotani ◽  
Hiroyuki Ueda
Keyword(s):  
Transverse Vibration ◽  
Rotation Frequency ◽  
Transmission Error ◽  
The Other ◽  
Belt Drive ◽  
Integer Multiple ◽  
Belt Drives ◽  
Eccentric Shaft ◽  
Synchronous Belt Drive ◽  
Frequency Variations

In synchronous belt drives, it is generally difficult to eliminate pulley eccentricity, because the pulley teeth and shaft hole are produced separately and the pulley is installed on an eccentric shaft. This eccentricity affects the accuracy of rotation transmission, so that the belt tension changes during a single rotation of the pulley. This in turn affects the occurrence of resonance in the spans. In the present study, the transmission error in a synchronous belt drive with an eccentric pulley in the absence of a transmitted load was experimentally investigated for the case in which the spans undergo first-mode transverse vibration due to resonance. The transmission error was found to have a component with a period equal to the span displacement, in addition to a component with a period of half the span displacement. During a single rotation of the pulley, the magnitude of the transmission error increased, and its frequency decreased, with decreasing belt tension. The transmission error exhibited the large value when two frequency conditions were satisfied: one was that the meshing frequency was within the range of span frequency variations due to the eccentricity, and the other was that the minimum span frequency was close to an integer multiple of the pulley rotation frequency. Even if both of these conditions occurred, if the range of span frequency variations due to the eccentricity was larger than 13 Hz, the transmission error could be eliminated by adjusting the belt tension, so that the average span frequency corresponded to the meshing frequency.

Transmission Error in Helical Synchronous Belt Drives in Bidirectional Operation: Influence of Pulley Flange Under No Load

2003 ◽  
Author(s):  
Masanori Kagotani ◽  
Kenichi Makita ◽  
Hiroyuki Ueda ◽  
Tomio Koyama
Keyword(s):  
Theoretical Analysis ◽  
Helix Angle ◽  
Transmission Error ◽  
Belt Drive ◽  
Alignment Error ◽  
Belt Drives ◽  
The Difference ◽  
Case Transmission ◽  
Synchronous Belt Drive ◽  
Outside Diameter

Helical synchronous belt drives are more effective than conventional synchronous belt drives with respect to reducing noise and transmission error per single pitch of the pulley. However, the helix angle of the tooth trace causes axial belt movement. Therefore, a flanged pulley is used in a helical synchronous belt drive. In the present study, the transmission error in a helical synchronous belt drive using a flanged pulley under installation tension was investigated both theoretically and experimentally for the case where the pulley was rotated in bidirectional operation. The computed transmission error agrees well with the experimental results, thereby confirming the applicability of the proposed theoretical analysis for transmission error. In this case, transmission error is found to be generated by the difference in axial belt movement between the driving and driven sides, and by a change in the state of contact between the belt and pulley teeth flanks. The transmission error is reduced when the installation tension is set higher than the tension that causes a change in contact direction between the tooth flanks. In addition, transmission error does not occur when the driving and driven pulleys are of equal outside diameter and have no pulley alignment error.

Sign in / Sign up

Export Citation Format

Share Document