Efficiency and Emissions Characteristics of Partially Premixed Dual-Fuel Combustion by Co-Direct Injection of NG and Diesel Fuel (DI2) - Part 2

2017 ◽  
Author(s):  
Gary D. Neely ◽  
Radu Florea ◽  
Jason Miwa ◽  
Zainal Abidin
Keyword(s):  
Diesel Fuel ◽  
Direct Injection ◽  
Fuel Combustion ◽  
Dual Fuel ◽  
Dual Fuel Combustion ◽  
Partially Premixed

Mapping the combustion modes of a dual-fuel compression ignition engine

2021 ◽  
pp. 146808742110183
Author(s):  
Jonathan Martin ◽  
André Boehman
Keyword(s):  
Direct Injection ◽  
Fuel Combustion ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Combustion Modes ◽  
Si Engines ◽  
Dual Fuel Combustion ◽  
Soot Emissions ◽  
Ci Engines

Compression-ignition (CI) engines can produce higher thermal efficiency (TE) and thus lower carbon dioxide (CO2) emissions than spark-ignition (SI) engines. Unfortunately, the overall fuel economy of CI engine vehicles is limited by their emissions of nitrogen oxides (NOx) and soot, which must be mitigated with costly, resource- and energy-intensive aftertreatment. NOx and soot could also be mitigated by adding premixed gasoline to complement the conventional, non-premixed direct injection (DI) of diesel fuel in CI engines. Several such “dual-fuel” combustion modes have been introduced in recent years, but these modes are usually studied individually at discrete conditions. This paper introduces a mapping system for dual-fuel CI modes that links together several previously studied modes across a continuous two-dimensional diagram. This system includes the conventional diesel combustion (CDC) and conventional dual-fuel (CDF) modes; the well-explored advanced combustion modes of HCCI, RCCI, PCCI, and PPCI; and a previously discovered but relatively unexplored combustion mode that is herein titled “Piston-split Dual-Fuel Combustion” or PDFC. Tests show that dual-fuel CI engines can simultaneously increase TE and lower NOx and/or soot emissions at high loads through the use of Partial HCCI (PHCCI). At low loads, PHCCI is not possible, but either PDFC or RCCI can be used to further improve NOx and/or soot emissions, albeit at slightly lower TE. These results lead to a “partial dual-fuel” multi-mode strategy of PHCCI at high loads and CDC at low loads, linked together by PDFC. Drive cycle simulations show that this strategy, when tuned to balance NOx and soot reductions, can reduce engine-out CO2 emissions by about 1% while reducing NOx and soot by about 20% each with respect to CDC. This increases emissions of unburnt hydrocarbons (UHC), still in a treatable range (2.0 g/kWh) but five times as high as CDC, requiring changes in aftertreatment strategy.

Effects of N-Butanol Content on the Dual-Fuel Combustion Mode With CNG at Two Engine Speeds

2018 ◽  
Author(s):  
Xiangyu Meng ◽  
Wuqiang Long ◽  
Yihui Zhou ◽  
Mingshu Bi ◽  
Chia-Fon F. Lee
Keyword(s):  
Thermal Efficiency ◽  
Engine Speed ◽  
Direct Injection ◽  
Fuel Combustion ◽  
Dual Fuel ◽  
Combustion Mode ◽  
Start Of Injection ◽  
Wide Range ◽  
Pilot Fuel ◽  
Dual Fuel Combustion

Because of the potential to reduce NOx and PM emissions simultaneously and the utilization of biofuel, diesel/compressed natural gas (CNG) dual-fuel combustion mode with port injection of CNG and direct injection of diesel has been widely studied. While in comparison with conventional diesel combustion mode, the dual-fuel combustion mode generally leads lower thermal efficiency, especially at low and medium load, and higher carbon monoxide (CO) and total hydrocarbons (THC) emissions. In this work, n-butanol was blended with diesel as the pilot fuel to explore the possibility to improve the performance and emissions of dual-fuel combustion mode with CNG. Various pilot fuels of B0 (pure diesel), B10 (90% diesel/10% n-butanol by volume basis), B20 (80% diesel/20% n-butanol) and B30 (70% diesel/30% n-butanol) were compared at the CNG substitution rate of 70% by energy basis under the engine speeds of 1400 and 1800 rpm. The experiments were carried out by sweeping a wide range of pilot fuel start of injection timings based on the same total input energy including pilot fuel and CNG. As n-butanol was added into the pilot fuel, the pilot fuel/CNG/air mixture tends to be more homogeneous. The results showed that for the engine speed of 1400 rpm, pilot fuel with n-butanol addition leads to a slightly lower indicated thermal efficiency (ITE). B30 reveals much lower NOx emission and slightly higher THC emissions. For the engine speed of 1800 rpm, B20 can improve ITE and decrease the NOx and THC emissions simultaneously relative to B0.

Influence of Diesel Fuel Injection Characteristics on Dual-Fuel Combustion Modes in a Large-Bore, Medium-Speed Engine

2018 ◽  
Author(s):  
Adam Klingbeil ◽  
Seunghyuck Hong ◽  
Roy J. Primus
Keyword(s):  
Natural Gas ◽  
Diesel Fuel ◽  
Fuel Combustion ◽  
Operating Conditions ◽  
Critical Parameters ◽  
Dual Fuel ◽  
Cycle Variation ◽  
Medium Speed ◽  
Substitution Ratio ◽  
Dual Fuel Combustion

Experiments were conducted on a large bore, medium speed, single cylinder, diesel engine to investigate operation with substitution ratio of natural gas varying from 0 to 93% by energy. As reported in a previous publication [1], these data were used to validate an analytical methodology for predicting performance and emissions under a broad spectrum of energy substitution ratios. For this paper, these experimental data are further analyzed to better understand the performance and combustion behavior under natural gas substitution ratios of 0%, 60% and 93%. These results show that by transitioning from diesel to 60% dual-fuel (60% NG substitution ratio), an improvement in the NOx-efficiency trade-off was observed that represented a ∼3% improvement in efficiency at constant NOx. Further, the transition from 60% dual-fuel to 93% dual-fuel (93% NG substitution ratio) resulted in additional efficiency improvement with a simultaneous reduction in NOx emissions. The data suggest that this improvement can be attributed to the premixed nature of the high substitution ratio. Furthermore, the results show that high cycle-to-cycle variation was observed for the 93% dual-fuel combustion tests. Further analysis, along with diesel injection rate measurements, show that the observed extreme sensitivity of the combustion event can be attributed to critical parameters such as diesel fuel quantity and injection timing. Results suggest a better understanding of the relative importance of combustion system components and operating conditions in controlling cycle-to-cycle variation of combustion process.

scholarly journals An Experimental Investigation on the Combustion and Emissions Performance of a Natural Gas–Diesel Dual Fuel Engine at Low and Medium Loads

2015 ◽  
Author(s):  
Hongsheng Guo ◽  
W. Stuart Neill ◽  
Brian Liko
Keyword(s):  
Carbon Monoxide ◽  
Particulate Matter ◽  
Natural Gas ◽  
Diesel Fuel ◽  
Fuel Combustion ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Dual Fuel ◽  
Particulate Matter Emissions ◽  
Dual Fuel Combustion

Natural gas is an abundant and inexpensive fuel in North America. It produces lower greenhouse gas emissions than diesel fuel when burned in an internal combustion engine. It is also considered to be a clean fuel because it generates lower particulate matter emissions than diesel fuel during combustion. In this study, an experimental study was conducted to investigate the combustion and emissions performance of a natural gas – diesel dual fuel engine at low and medium loads. A single cylinder direct injection diesel engine was modified to operate as the dual fuel engine. The diesel fuel was directly injected into the cylinder, while natural gas was injected into the intake port. The operating conditions, such as engine speed, load, intake temperature and pressure, were well controlled during the experiment. The effect of natural gas fraction on energy efficiency, cylinder pressure, exhaust temperature, and combustion stability were recorded and analyzed. The emissions data, including particulate matter, nitric oxides, carbon monoxide, and methane at various natural gas fractions and operating conditions were also analyzed. The results showed that natural gas – diesel dual fuel combustion slightly decreased brake thermal efficiency at low and medium load conditions and significantly reduced carbon dioxide and particulate matter emissions. Methane and NOx emissions increased in dual fuel combustion mode compared to diesel operation. The variation of carbon monoxide emissions in dual fuel mode depended on load and speed conditions.

Sign in / Sign up

Export Citation Format

Share Document