scholarly journals Parametric 1-D Modeling Study of a 5-Stroke Spark-Ignition Engine Concept for Increasing Engine Thermal Efficiency

2015 ◽  
Author(s):  
Alex Melin ◽  
David Kittelson ◽  
William Northrop
Keyword(s):  
Thermal Efficiency ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Engine Concept ◽  
Modeling Study

Simulation of Extended Expansion Lean Burn Spark Ignition Engine

2004 ◽  
Author(s):  
A. Manivannan ◽  
R. Ramprabhu ◽  
P. Tamilporai ◽  
S. Chandrasekaran
Keyword(s):  
Heat Transfer ◽  
Compression Ratio ◽  
Thermal Efficiency ◽  
Numerical Study ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Valve Closure ◽  
Intake Valve ◽  
Lean Burn ◽  
Atkinson Cycle

This paper deals with Numerical Study of 4-stoke, Single cylinder, Spark Ignition, Extended Expansion Lean Burn Engine. Engine processes are simulated using thermodynamic and global modeling techniques. In the simulation study following process are considered compression, combustion, and expansion. Sub-models are used to include effect due to gas exchange process, heat transfer and friction. Wiebe heat release formula was used to predict the cylinder pressure, which was used to find out the indicated work done. The heat transfer from the cylinder, friction and pumping losses also were taken into account to predict the brake mean effective pressure, brake thermal efficiency and brake specific fuel consumption. Extended Expansion Engine operates on Otto-Atkinson cycle. Late Intake Valve Closure (LIVC) technique is used to control the load. The Atkinson cycle has lager expansion ratio than compression ratio. This is achieved by increasing the geometric compression ratio and employing LIVC. Simulation result shows that there is an increase in thermal efficiency up to a certain limit of intake valve closure timing. Optimum performance is attained at 90 deg intake valve closure (IVC) timing further delaying the intake valve closure reduces the engine performance.

scholarly journals Experimental investigation on combustion, performance, and emissions characteristics of butanol as an oxygenate in a spark ignition engine

2017 ◽  
Vol 9 (2) ◽  
pp. 168781401668884 ◽  
Author(s):  
Yu Li ◽  
Jinke Gong ◽  
Wenhua Yuan ◽  
Jun Fu ◽  
Bin Zhang ◽  
...  
Keyword(s):  
Carbon Monoxide ◽  
Nitrogen Oxides ◽  
Thermal Efficiency ◽  
Alternative Fuel ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Combustion Performance ◽  
Performance And Emissions ◽  
Unburned Hydrocarbons

Ethanol is known as the most widely used alternative fuel for spark-ignition engines. Compared to it, butanol has proved to be a very promising renewable fuel in recent years for desirable properties. The conjoint analysis on combustion, performance, and emissions characteristics of a port fuel injection spark-ignition engine fueled with butanol–gasoline blends was carried out. In comparison with butanol–gasoline blends with various butanol ratio (0–60 vol% referred as G100~B60) and conventional alcohol alternative fuels (methanol, ethanol, and butanol)–gasoline blends, it shows that B30 performs well in engine performance and emissions, including brake thermal efficiency, brake-specific fuel consumption, carbon monoxide, unburned hydrocarbons, and nitrogen oxides. Then, B30 was compared with G100 under various equivalence ratios ( Φ = 0.83–1.25) and engine loads (3 and 5-bar brake mean effective pressure). In summary, B30 presents an advanced combustion phasing, which leads to a 0.3%–2.8% lower brake thermal efficiency than G100 as the engine was running at the spark timing of gasoline’s maximum brake torque (MBT). Therefore, the sparking timing should be postponed when fueled with butanol–gasoline blends. For emissions, the lower carbon monoxide (2.3%–8.7%), unburned hydrocarbons (12.4%–27.5%), and nitrogen oxides (2.8%–19.6%) were shown for B30 compared with G100. Therefore, butanol could be a good alternative fuel to gasoline for its potential to improve combustion efficiency and reduce pollutant emissions.

scholarly journals Efficiency characteristics of a new quasi-constant volume combustion spark ignition engine

2013 ◽  
Vol 17 (1) ◽  
pp. 119-133 ◽  
Author(s):  
Jovan Doric ◽  
Ivan Klinar
Keyword(s):  
Engine Speed ◽  
Combustion Process ◽  
Spark Ignition ◽  
Constant Volume ◽  
Spark Ignition Engine ◽  
Si Engine ◽  
Piston Mechanism ◽  
Si Engines ◽  
Ic Engines ◽  
Engine Concept

A zero dimensional model has been used to investigate the combustion performance of a four cylinder petrol engine with unconventional piston motion. The main feature of this new spark ignition (SI) engine concept is the realization of quasi-constant volume (QCV) during combustion process. Presented mechanism is designed to obtain a specific motion law which provides better fuel consumption of internal combustion (IC) engines. These advantages over standard engine are achieved through synthesis of unconventional piston mechanism. The numerical calculation was performed for several cases of different piston mechanism parameters, compression ratio and engine speed. Calculated efficiency and power diagrams are plotted and compared with performance of ordinary SI engine. The results show that combustion during quasi-constant volume has significant impact on improvement of efficiency. The main aim of this paper is to find a proper kinematics parameter of unconventional piston mechanism for most efficient heat addition in SI engines.

First and Second Law Analyses of a Spark-Ignition Engine Using Either Isooctane or Hydrogen: An Initial Assessment

2006 ◽  
Author(s):  
Jerald A. Caton
Keyword(s):  
Nitric Oxide ◽  
Thermal Efficiency ◽  
Equivalence Ratio ◽  
Performance Metrics ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Second Law ◽  
Cycle Simulation ◽  
Nitric Oxide Emissions

The use of either hydrogen or isooctane for a spark-ignition engine was examined using a thermodynamic cycle simulation including the second law of thermodynamics. The engine studied was a 5.7 liter, automotive engine operating from idle to wide open throttle. The hydrogen or isooctane was assumed premixed with the air. Two features of hydrogen combustion that were included in the study were the higher flame speeds (shorter burn durations) and the wider lean flammability limits (lean equivalence ratios). Three cases were considered for the use of hydrogen: (1) standard burn duration and an equivalence ratio of 1.0, (2) a shorter burn duration and an equivalence ratio of 1.0, and (3) a shorter burn duration and variable, lean equivalence ratios. The results included thermal efficiencies, other performance metrics, second law parameters, and nitric oxide emissions. In general, for the cases with an equivalence of 1.0, the brake thermal efficiency was slightly lower for the hydrogen cases due to the higher temperatures and higher heat losses. For the variable, lean equivalence ratio cases, the thermal efficiency was higher for the hydrogen case relative to the isooctane case. Due to the higher temperatures, the hydrogen cases had over 50% higher nitric oxide emissions compared to the isooctane case at the base conditions. In addition, the second law analyses indicated that the destruction of availability during the combustion process was lower for the base hydrogen case (11.2%) relative to the isooctane case (21.1%).

scholarly journals INVESTIGATION OF MULTI-ZONE MODELS FOR SPARK IGNITION ENGINE FUELED WITH ETHANOL

2021 ◽  
Vol 22 (2) ◽  
pp. 339-351
Author(s):  
A. A. Dare ◽  
Olanrewaju Olatunde ◽  
O. S. Ismail ◽  
A. S. Shote ◽  
O. J. Alamu ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Ignition Time ◽  
High Volume ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Zone Model ◽  
Fuel Blends ◽  
Indicated Mean Effective Pressure ◽  
First Case

This research is aimed at investigating the effect of using ethanol (E100) in multi-zone model analysis consisting of multi-combustion chamber zoning cases. The first case considered is a three-zone model that has an unburned zone, burned zone, and transitory zone. The second case model is also three-zone, consisting of an unburned zone and two partitioned burned zones. The burned zone was imagined partitioned into burned zone-1 and burned zone-2 under uneven fuel distribution having different equivalent ratios. The third case is a four-zone model including two regions of burned zone, an unburned zone and a transitory zone, which is unburned burned zone containing a mixture of unburned and burned gases. Arbitrary constants for each of the unburned (CC1) and burned (CC2) Zone leakages in the unburned burned Zone are 0.00025, 0.0005, 0.001, 0.002, 0.005, 0.1 and 0.5. The Mass Fraction Burned (MFB) for zone-1, x1 and burned zone-2, x2 are computed using Partitioned Burnt Zones Ratios (PBZR) of 2:8, 3:7, 4:6, 5:5, 6:4, 7:3 and 8:2. Two equivalent ratios, one for each fuel MFB (?1, ?2), (0.8, 0.6) and (0.6, 0.8) are analyzed using fuel blends of varying percentage. A comparison of values of the three zoning cases is done using peak values from the three-zone models to evaluate the four-zone model. The model was compared with a spark ignition engine (SIE) operating with a premium motor spirit (PMS) serving as baseline. The engine operating conditions were set at an engine speed of 2000 rpm, -35bTDC ignition time, and burn duration at 60 oC. The indicated mean effective pressure (IMEP), thermal efficiency (?), cylinder pressure and emission fraction from the developed models and those of two-zone analysis obtained agreed with literature values. The result showed it is undesirable to have a high volume of burned charge as infiltrate. The three-zone segmented model predicted the highest engine thermal efficiency and peak pressure at mass burn ratio of 7:3. A general reduction in N2 emission was observed for the three-zone transitional and four-zone models. ABSTRAK: Kajian ini menilai kesan etanol (E100) dalam analisis model zon-berbilang yang terdapat pada masalah pengezonan kebuk pembakaran-berbilang. Kes pertama yang diambil kira adalah model tiga-zon yang mempunyai zon tidak terbakar, zon terbakar dan zon peralihan. Model kedua merupakan juga tiga-zon yang terdiri daripada zon tidak-terbakar dan dua zon bahagian yang terbakar. Zon yang terbakar dibahagikan kepada zon-1 terbakar dan zon-2 terbakar di bawah kebakaran tidak sekata yang mempunyai nisbah berlainan. Kes ketiga adalah model zon-keempat termasuk dua kawasan zon terbakar, zon tidak-terbakar dan zon peralihan iaitu zon terbakar tidak-terbakar di mana ia adalah campuran gas terbakar dan tidak-terbakar. Tetapan sebarangan bagi setiap zon kebocoran tidak-terbakar (CC1) dan terbakar (CC2) dalam zon terbakar tidak-terbakar adalah 0.00025, 0.0005, 0.001, 0.002, 0.005, 0.1 dan 0.5. Pecahan Jisim Terbakar (MFB) bagi zon-1, x1 dan zon-2 terbakar, x2 dikira menggunakan Nisbah Zon Bahagian Terbakar (PBZR) sebanyak 2:8, 3:7, 4:6, 5:5, 6:4, 7:3 dan 8:2. Nisbah dua persamaan, setiap satu bahan api MFB adalah (?1, ?2), (0.8, 0.6) dan (0.6, 0.8) dan diuji menggunakan pelbagai peratus bahan api campuran. Nilai perbandingan bagi tiga kes zon dibuat menggunakan nilai puncak dari model tiga-zon bagi menilai model empat-zon. Model ini dibandingkan dengan enjin cucuhan bunga api (SIE) beroperasi dengan motor alkohol premium (PMS) sebagai garis asas. Keadaan operasi enjin adalah dihadkan pada 2000 rpm kelajuan enjin, masa pencucuhan -35bTDC dan tempoh pembakaran pada 60 oC. Tekanan berkesan min tertunjuk (IMEP), kecekapan haba tertunjuk (?), tekanan silinder dan pecahan pengeluaran dari model yang dibangunkan dan analisis dua-zon yang terhasil adalah sama dengan nilai literatur. Dapatan kajian menunjukkan cas terbakar pada isipadu yang banyak adalah tidak diingini sebagai penyerap. Model tiga bahagian zon menunjukkan kecekapan haba enjin tertinggi dan tekanan puncak pada jisim bakar dengan nisbah 7:3. Manakala, pengurangan umum telah diperhatikan pada pengeluaran N2 di peralihan tiga-zon dan model empat zon.

Analysis of Thermal Efficiency in a Hydrogen Premixed Spark Ignition Engine

1999 ◽  
Author(s):  
Toshio Shudo ◽  
Yasuo Nakajima ◽  
Takayuki Futakuchi
Keyword(s):  
Combustion Chamber ◽  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Combustion Process ◽  
Methane Combustion ◽  
Spark Ignition ◽  
Hydrogen Combustion ◽  
Spark Ignition Engine ◽  
Chamber Wall ◽  
Flame Velocity

Abstract Hydrogen has higher flame velocity and smaller quenching distance than hydrocarbon fuels, and is supposed to have special characteristics in combustion process of internal combustion engines. In this research, contributors to thermal efficiency in a hydrogen premixed spark ignition engine were analyzed and compared with methane combustion. Results showed hydrogen combustion had higher cooling loss to combustion chamber wall, and thermal efficiency of hydrogen combustion was mainly dominated by both cooling loss to combustion chamber wall and degree of constant volume combustion.

Experimental Investigation of a Simulated Byproduct Fuel Mixture From the Cl-ODH Process in a Spark-Ignition Engine

2021 ◽  
Author(s):  
Matt Gore ◽  
Kaushik Nonavinakere Vinod ◽  
Tiegang Fang
Keyword(s):  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Load Condition ◽  
Fuel Mixture ◽  
Spark Ignition ◽  
Active Species ◽  
Spark Ignition Engine ◽  
Process Efficiency ◽  
Mixed Gas ◽  
Minor Compounds

Abstract The study investigates a fuel mixture with ethane and methane as active species and a high dilution of CO2 for application in a spark-ignition (SI) engine. The simplified fuel mixture used is a byproduct of a chemical looping based oxidative dehydrogenation (Cl-ODH) process to convert ethane to ethylene. The byproduct gas mixture has a concentration of 41% CO2, 40% ethane, and 5% methane by weight along with other minor compounds. Varying mixtures of ethane and methane were selected and combined with between 42 to 46 percent by weight CO2 to evaluate the viability and efficiency of this fuel to operate in existing internal combustion engines as a means for reducing emissions and improving the process efficiency of the Cl-ODH process. An experimental test stand was built based on a 13 hp gasoline generator with modified gas induction. The engine was also instrumented for data acquisition from the engine. A gas metering and mixing system was installed to precisely control the mass of gases induced into the engine. Various instrumentation was installed on the engine to monitor in-cylinder pressure, temperature at various locations, emissions, and fuel and airflow rates. Varying loads were applied and flow rates of the gases were induced to simulate different mixtures. It was found that under a high load, the mixed gas was able to generate comparable thermal efficiency and power to gasoline. But under no load or a part load condition the indicated thermal efficiency was found to be lower than that of gasoline. Further, the mixed gas also resulted in lower CO and NOx emissions compared to gasoline. The application of this work is an alternative fuel for existing engines that with little modification can operate effectively and benefit the overall process of ethylene generation.

Thermodynamic analysis of using ethanol-methanol-gasoline (GEM) blends in a turbocharged, spark-ignition engine

2021 ◽  
pp. 1-28
Author(s):  
Hongqing Feng ◽  
Shuwen Xiao ◽  
Zhirong Nan ◽  
Di Wang ◽  
Chaohe Yang
Keyword(s):  
Thermal Efficiency ◽  
Fossil Fuel ◽  
Spark Ignition ◽  
Exergy Efficiency ◽  
Spark Ignition Engine ◽  
Low Carbon ◽  
Si Engine ◽  
Engine Load ◽  
Maximum Value ◽  
Spark Timing

Abstract Low-carbon alcohols have been universally acknowledged as an alternative to fossil fuel in the world, which is environmentally friendly and clean. In this paper, the detailed exergy and energy analysis were carried out on a turbocharged, spark-ignition (SI) engine fueled with methanol-ethanol-gasoline (GEM) under non-knock conditions. The results indicated that increasing the alcohols proportion in blends could slightly improve the exergy efficiency and thermal efficiency and increase the percentage of total irreversibility in the total exergy. The thermal efficiency and exergy efficiency increased to a maximum value and then decreased, while the proportion of total irreversibility in the total exergy increased significantly with the spark timing retarded from the earliest timing. The exergy efficiency and thermal efficiency increased as the engine load increased. Additionally, the total irreversibility increased but the proportion of total irreversibility in the total exergy presented a trend of decreasing as the engine load increased.

Sign in / Sign up

Export Citation Format

Share Document