Numerical Simulation and Experimental Research on PPC Combustion and Emissions Characteristics of Diesel Engine

2015 ◽  
Author(s):  
Bei Liu ◽  
Xiaobei Cheng ◽  
Liang Qiu ◽  
Shijun Dong ◽  
Xin Wang
Keyword(s):  
Numerical Simulation ◽  
Diesel Engine ◽  
Experimental Research

Laser shock micro-bulk forming: Numerical simulation and experimental research

2021 ◽  
Vol 64 ◽  
pp. 1273-1286
Author(s):  
Keyang Wang ◽  
Huixia Liu ◽  
Youjuan Ma ◽  
Jinzhong Lu ◽  
Xiao Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Experimental Research ◽  
Laser Shock ◽  
Bulk Forming

scholarly journals Influence of Vortex Finder Structure on Separation Performance of Double-Overflow Three-Product Hydrocyclones

Separations ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 79
Author(s):  
Yuekan Zhang ◽  
Jiangbo Ge ◽  
Lanyue Jiang ◽  
Hui Wang ◽  
Junru Yang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Experimental Research ◽  
Separation Efficiency ◽  
Structural Parameters ◽  
Separation Performance ◽  
Insertion Depth ◽  
Flow Field Characteristics ◽  
Vortex Finder ◽  
Fine Classification

In view of the difficulty of traditional hydrocyclones to meet the requirements of fine classification, a double-overflow three-product (internal overflow, external overflow and underflow) hydrocyclone was designed in this study. Numerical simulation and experimental research methods were used to investigate the effects of double-overflow flow field characteristics and structural parameters (i.e., internal vortex finder diameter and insertion depth) on separation performance. The research results showed that the larger the diameter of the internal vortex finder, the greater the overflow yield and the larger the cut size. The finest internal overflow product can be obtained when the internal vortex finder is 30 mm longer than the external vortex finder. The separation efficiency is highest when the internal vortex finder is 30 mm shorter than the external vortex finder.

Theoretical Calculation and Experimental Research on Sequential Turbocharging of a Marine Diesel Engine

2011 ◽  
Vol 305 ◽  
pp. 416-422
Author(s):  
Peng Qi Zhang ◽  
Qing Lin He ◽  
Yin Yan Wang
Keyword(s):  
Diesel Engine ◽  
Theoretical Calculation ◽  
Experimental Research ◽  
Marine Diesel Engine ◽  
Test Results ◽  
Low Load ◽  
Marine Diesel ◽  
Working Principle ◽  
Test Result

The paper introduces the working principle of the sequential turbo-charging (STC) system of multi-turbocharger. To improve low-load performance and operating economy of the 234V12 diesel engine, a STC system of multi-turbocharger for the diesel engine was designed. Theoretical calculation and experimental research was done on this improved marine diesel engine. Then, a 3-phase STC system is presented by analyzing and comparing the test result and the switching boundary of this system is confirmed. The test results show that the low-load performance is improved obviously by use of multi-turbocharger STC system.

A Numerical Simulation of Fuel Premixing for PCCI Combustion by Direct Injection

2011 ◽  
Author(s):  
Tsuyoshi Kondo ◽  
Tsuguhiko Nakagawa
Keyword(s):  
Numerical Simulation ◽  
Diesel Engine ◽  
Direct Injection ◽  
Vertical Direction ◽  
General Purpose ◽  
Injection Timing ◽  
Injection Angle ◽  
Equivalent Ratio ◽  
Local Equivalent ◽  
The Rich

Diesel engine has some advantages that thermal efficiency is high and control response is fast. On the other hand, more particulate matter (PM) and nitrogen oxide (NOx) are contained in the exhaust gas of diesel engine. Premixed charge compression ignition (PCCI) combustion is proposed to reduce the PM and NOx. In the lean range of equivalent ratio, unburned fuel is left and in the rich range, PM and soot are generated. For the practical use of PCCI combustion, mixing fuel and air well is important under the low equivalent ratio of injection. In this study, the mixing characteristics of fuel and air in a cylinder were numerically evaluated. A numerical simulation was performed with general-purpose simulator. The fuel has been injected into the vertical direction of cylinder and injection angle has been defined as 0 degree. In order to express the collusion, impingement on the wall model, that defines behavior of a droplet impinged on the wall with the Weber number of a droplet, was applied. By the injection timing, standard deviation of local equivalent ratio at Top Dead Center (TDC) was plotted. In this study, Frequency of mixing in each cell statistically was observed to evaluate the fuel-air mixing degree. The authors have taken notice of the condition which can be reduced the amount of scatter in the distribution of local equivalent ratio.

Sign in / Sign up

Export Citation Format

Share Document