Comparison of Negative Valve Overlap (NVO) and Rebreathing Valve Strategies on a Gasoline PPC Engine at Low Load and Idle Operating Conditions

2013 ◽  
Vol 6 (1) ◽  
pp. 366-378 ◽  
Author(s):  
Patrick Borgqvist ◽  
Per Tunestal ◽  
Bengt Johansson
Keyword(s):  
Operating Conditions ◽  
Low Load ◽  
Negative Valve Overlap ◽  
Valve Overlap

Assessment of Residual Mass Estimation Methods for Cylinder Pressure Heat Release Analysis of HCCI Engines With Negative Valve Overlap

2011 ◽  
Author(s):  
Elliott A. Ortiz-Soto ◽  
Jiri Vavra ◽  
Aristotelis Babajimopoulos
Keyword(s):  
Heat Release ◽  
State Equation ◽  
Operating Conditions ◽  
Exhaust Valve ◽  
Estimation Methods ◽  
Cylinder Pressure ◽  
Hcci Engines ◽  
Release Analysis ◽  
Negative Valve Overlap ◽  
Valve Overlap

Increased residual levels in Homogeneous Charge Compression Ignition (HCCI) engines employing valve strategies such as recompression or negative valve overlap (NVO) imply that accurate estimation of residual gas fraction (RGF) is critical for cylinder pressure heat release analysis. The objective of the present work was to evaluate three residual estimation methods and assess their suitability under naturally aspirated and boosted HCCI operating conditions: i) the Simple State Equation method employs the Ideal Gas Law at exhaust valve closing (EVC); ii) the Mirsky method assumes isentropic exhaust process; and iii) the Fitzgerald method models in-cylinder temperature from exhaust valve opening (EVO) to EVC by accounting for heat loss during the exhaust process and uses measured exhaust temperature for calibration. Simulations with a calibrated and validated “virtual engine” were performed for representative HCCI operating conditions of engine speed, fuel-air equivalence ratio, NVO and intake pressure (boosting). The State Equation method always overestimated RGF by more than 10%. The Mirsky method was most robust, with average errors between 3–5%. The Fitzgerald method performed consistently better, ranging from no error to 5%, where increased boosting caused the largest discrepancies. A sensitivity study was also performed and determined that the Mirsky method was most robust to possible pressure and temperature measurement errors.

The Low Load Limit of Gasoline Partially Premixed Combustion Using Negative Valve Overlap

2012 ◽  
Author(s):  
Patrick Borgqvist ◽  
Öivind Andersson ◽  
Per Tunestål ◽  
Bengt Johansson
Keyword(s):  
Engine Speed ◽  
Premixed Combustion ◽  
Partially Premixed Combustion ◽  
Operating Region ◽  
Load Limit ◽  
Low Load ◽  
Negative Valve Overlap ◽  
Valve Overlap ◽  
Injection Strategies ◽  
High Octane

Partially premixed combustion has the potential of high efficiency and simultaneous low soot and NOx emissions. Running the engine in PPC mode with high octane number fuels has the advantage of a longer premix period of fuel and air which reduces soot emissions, even at higher loads. The problem is the ignitability at low load and idle operating conditions. The objective is to investigate different multiple-injection strategies in order to further expand the low load limit and reduce the dependency on negative valve overlap in order to increase efficiency. The question is, what is the minimum attainable load for a given setting of negative valve overlap and fuel injection strategy. The experimental engine is a light duty diesel engine equipped with a fully flexible valve train system. The engine is run without boost at engine speed 800 rpm. The fuel is 87 RON gasoline. A turbocharger is typically used to increase the boost pressure, but at low engine speed and load the available boost is expected to be limited. The in-cylinder pressure and temperature around top-dead-center will then be too low to ignite high octane number fuels. A negative valve overlap can be used to extend the low engine speed and load operating region. But one of the problems with negative valve overlap is the decrease in gas-exchange efficiency due to heat-losses from recompression of the residual gases. Also, the potential temperature increase from the trapped hot residual gases is limited at low load due to the low exhaust gas temperature. In order to expand the low load operating region further, more advanced injection strategies are investigated.

Assessment of Residual Mass Estimation Methods for Cylinder Pressure Heat Release Analysis of HCCI Engines With Negative Valve Overlap

2012 ◽  
Vol 134 (8) ◽  
Author(s):  
Elliott A. Ortiz-Soto ◽  
Jiri Vavra ◽  
Aristotelis Babajimopoulos
Keyword(s):  
Heat Release ◽  
State Equation ◽  
Operating Conditions ◽  
Exhaust Valve ◽  
Estimation Methods ◽  
Cylinder Pressure ◽  
Hcci Engines ◽  
Release Analysis ◽  
Negative Valve Overlap ◽  
Valve Overlap

Increased residual levels in homogeneous charge compression ignition (HCCI) engines employing valve strategies such as recompression or negative valve overlap (NVO) imply that accurate estimation of residual gas fraction (RGF) is critical for cylinder pressure heat release analysis. The objective of the present work was to evaluate three residual estimation methods and assess their suitability under naturally aspirated and boosted HCCI operating conditions: (i) the simple state equation method employs the ideal gas law at exhaust valve closing (EVC); (ii) the Mirsky method assumes isentropic exhaust process; and (iii) the Fitzgerald method models in-cylinder temperature from exhaust valve opening (EVO) to EVC by accounting for heat loss during the exhaust process and uses measured exhaust temperature for calibration. Simulations with a calibrated and validated “virtual engine” were performed for representative HCCI operating conditions of engine speed, fuel-air equivalence ratio, NVO and intake pressure (boosting). The state equation method always overestimated RGF by more than 10%. The Mirsky method was most robust, with average errors between 3–5%. The Fitzgerald method performed consistently better, ranging from no error to 5%, where increased boosting caused the largest discrepancies. A sensitivity study was also performed and determined that the Mirsky method was most robust to possible pressure and temperature measurement errors.

Internal exhaust gas recirculation via reinduction and negative valve overlap for fuel-efficient aftertreatment thermal management at curb idle in a diesel engine

2021 ◽  
pp. 146808742098459
Author(s):  
Mrunal C Joshi ◽  
Gregory M Shaver ◽  
Kalen Vos ◽  
James McCarthy ◽  
Lisa Farrell
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Management ◽  
Lower Fuel Consumption ◽  
Low Load ◽  
Negative Valve Overlap ◽  
Valve Overlap ◽  
Gas Recirculation ◽  
Cycle Efficiency ◽  
Management Operation

Low air-flow diesel engine strategies are advantageous during low load operation to maintain temperatures of a warmed-up aftertreatment system (ATS) while reducing fuel consumption and engine-out emissions. This paper presents results at curb idle for internal EGR (iEGR) that demonstrate low airflow and reduced engine-out emissions during fuel-efficient ATS temperature maintenance operation. Internal EGR via reinduction and trapping using negative valve overlap (NVO) are compared to each other, conventional operation and to other low airflow approaches including cylinder deactivation (CDA). At 800 RPM/1.3 bar BMEP (curb idle) iEGR via reinduction enables 200°C engine-out temperature combined with 70% lower NO X, 35% lower fuel consumption, and 40% lower exhaust flow rate than conventional thermal management operation. Internal EGR via trapping using NVO resulted in an engine-out temperature of 185°C, with 56% lower NO X and 25% lower fuel consumption than conventional thermal management operation. Both iEGR strategies have lower engine-out temperatures and higher exhaust flow rates than CDA. No external EGR is required for either iEGR strategy. “iEGR via reinduction” outperforms “iEGR via NVO” as a result of higher open cycle efficiency (via less pumping work) and higher closed-cycle efficiency (via higher specific heat ratio).

scholarly journals Tailoring Charge Reactivity Using In-Cylinder Generated Reformate for Gasoline Compression Ignition Strategies

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Isaac W. Ekoto ◽  
Benjamin M. Wolk ◽  
William F. Northrop ◽  
Nils Hansen ◽  
Kai Moshammer
Keyword(s):  
Performance Metrics ◽  
Engine Performance ◽  
Gas Temperature ◽  
Exhaust Temperature ◽  
Start Of Injection ◽  
Low Load ◽  
Main Period ◽  
Ignition Characteristics ◽  
Negative Valve Overlap ◽  
Valve Overlap

In-cylinder reforming of injected fuel during a negative valve overlap (NVO) recompression period can be used to optimize main-cycle combustion phasing for low-load low-temperature gasoline combustion (LTGC). The objective of this work is to examine the effects of reformate composition on main-cycle engine performance. An alternate-fire sequence was used to generate a common exhaust temperature and composition boundary condition for a cycle-of-interest, with performance metrics measured for these custom cycles. NVO reformate was also separately collected using a dump-valve apparatus and characterized by both gas chromatography (GC) and photoionization mass spectroscopy (PIMS). To facilitate gas sample analysis, sampling experiments were conducted using a five-component gasoline surrogate (iso-octane, n-heptane, ethanol, 1-hexene, and toluene) that matched the molecular composition, 50% boiling point, and ignition characteristics of the research gasoline. For the gasoline, it was found that an advance of the NVO start-of-injection (SOI) led to a corresponding advance in main-period combustion phasing as the combination of longer residence times and lower amounts of liquid spray piston impingement led to a greater degree of fuel decomposition. The effect was more pronounced as the fraction of total fuel injected in the NVO period increased. Main-period combustion phasing was also found to advance as the main-period fueling decreased. Slower kinetics for leaner mixtures were offset by a combination of increased bulk-gas temperature from higher charge specific heat ratios and increased fuel reactivity due to higher charge reformate fractions.

The Low Load Limit of Gasoline Partially Premixed Combustion Using Negative Valve Overlap

2013 ◽  
Vol 135 (6) ◽  
Author(s):  
Patrick Borgqvist ◽  
Öivind Andersson ◽  
Per Tunestål ◽  
Bengt Johansson
Keyword(s):  
Engine Speed ◽  
Premixed Combustion ◽  
Partially Premixed Combustion ◽  
Operating Region ◽  
Load Limit ◽  
Low Load ◽  
Partially Premixed ◽  
Negative Valve Overlap ◽  
Valve Overlap ◽  
Injection Strategies

Partially premixed combustion has the potential of high efficiency and simultaneous low soot and NOx emissions. Running the engine in partially premixed combustion mode with high octane number fuels has the advantage of a longer premix period of fuel and air which reduces soot emissions, even at higher loads. The problem is the ignitability at low load and idle operating conditions. The objective is to investigate different multiple-injection strategies in order to further expand the low load limit and reduce the dependency on negative valve overlap in order to increase efficiency. The question is, what is the minimum attainable load for a given setting of negative valve overlap and fuel injection strategy. The experimental engine is a light duty diesel engine equipped with a fully flexible valve train system. The engine is run without boost at engine speed 800 rpm. The fuel is 87 RON gasoline. A turbocharger is typically used to increase the boost pressure, but at low engine speed and load the available boost is expected to be limited. The in-cylinder pressure and temperature around top-dead-center will then be too low to ignite high octane number fuels. A negative valve overlap can be used to extend the low engine speed and load operating region. But one of the problems with negative valve overlap is the decrease in gas-exchange efficiency due to heat-losses from recompression of the residual gases. Also, the potential temperature increase from the trapped hot residual gases is limited at low load due to the low exhaust gas temperature. In order to expand the low load operating region further, more advanced injection strategies are investigated.

Low Load Limit Extension for Gasoline Compression Ignition Using Negative Valve Overlap Strategy

2018 ◽  
Author(s):  
R. Vallinayagam ◽  
Abdullah S. AlRamadan ◽  
S Vedharaj ◽  
Yanzhao An ◽  
Jaeheon Sim ◽  
...  
Keyword(s):  
Compression Ignition ◽  
Load Limit ◽  
Low Load ◽  
Negative Valve Overlap ◽  
Valve Overlap

Numerical study on combustion characteristics of six-stroke-cycle gasoline compression ignition engine with continuously variable valve duration valve technology

2019 ◽  
Vol 22 (1) ◽  
pp. 165-183 ◽  
Author(s):  
Oudumbar Rajput ◽  
Youngchul Ra ◽  
Kyoung-Pyo Ha ◽  
You-Sang Son
Keyword(s):  
Numerical Study ◽  
Power Stroke ◽  
Compression Ignition ◽  
Ignition Timing ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Wide Range ◽  
Negative Valve Overlap ◽  
Variable Valve ◽  
Valve Overlap

Engine performance and emissions of a six-stroke gasoline compression ignition engine with a wide range of continuously variable valve duration control were numerically investigated at low engine load conditions. For the simulations, an in-house three-dimensional computational fluid dynamics code with high-fidelity physical sub-models was used, and the combustion and emission kinetics were computed using a reduced kinetics mechanism for a 14-component gasoline surrogate fuel. Variation of valve timing and duration was considered under both positive valve overlap and negative valve overlap including the rebreathing of intake valves via continuously variable valve duration control. Close attention was paid to understand the effects of two additional strokes of the engine cycle on the thermal and chemical conditions of charge mixtures that alter ignition, combustion and energy recovery processes. Double injections were found to be necessary to effectively utilize the additional two strokes for the combustion of overly mixed lean charge mixtures during the second power stroke. It was found that combustion phasing in both power strokes is effectively controlled by the intake valve closure timing. Engine operation under negative valve overlap condition tends to advance the ignition timing of the first power stroke but has minimal effect on the ignition timing of second power stroke. Re-breathing was found to be an effective way to control the ignition timing in second power stroke at a slight expense of the combustion efficiency. The operation of a six-stroke gasoline compression ignition engine could be successfully simulated. In addition, the operability range of the six-stroke gasoline compression ignition engine could be substantially extended by employing the continuously variable valve duration technique.

Sign in / Sign up

Export Citation Format

Share Document