Assessment of Optimization Methodologies to Study the Effects of Bowl Geometry, Spray Targeting and Swirl Ratio for a Heavy-Duty Diesel Engine Operated at High-Load

2008 ◽  
Vol 1 (1) ◽  
pp. 537-557 ◽  
Author(s):  
Yu Shi ◽  
Rolf D. Reitz
Keyword(s):  
Diesel Engine ◽  
High Load ◽  
Swirl Ratio ◽  
Heavy Duty ◽  
Heavy Duty Diesel Engine ◽  
Heavy Duty Diesel

scholarly journals Effects of multiple injections on combustion and emissions in a heavy-duty diesel engine at high load and low speed

2020 ◽  
Vol 12 (12) ◽  
pp. 168781402098462
Author(s):  
Yingying Lu ◽  
Yize Liu
Keyword(s):  
Diesel Engine ◽  
Single Injection ◽  
High Load ◽  
Post Injection ◽  
Heavy Duty ◽  
Low Speed ◽  
Multiple Injections ◽  
Heavy Duty Diesel Engine ◽  
Main Injection ◽  
Heavy Duty Diesel

Advanced multiple injection strategies have been suggested for compression ignition engines in order to meet the increasingly stringent emission regulations. Experiments and simulations were used to study effects of the main-injection mode (times), the post-injection proportion, and timing on combustion and emissions in a heavy-duty diesel engine at high load and constant low speed. The results reveal the following. The NOx emissions of 1main+1post, 2main+1post, and 3main+1post injections are all lower than those of single injection; the higher the number of main-injection pluses, the lower the NOx emissions. Enough main-post injection interval is needed to ensure post and main injections are relatively independent to entrain more fresh air to decrease the soot. Over-retarded post-injection timing tends to increase the soot due to the lower in-cylinder temperature. The combined effects of formation and oxidation determine the final soot. To gain the best trade-off of NOx and soot, compared with single injection, for the three multiple injections, the lowest soot emissions are gained at post-injection proportions of 15% and post-injection timings of 25°, 30°, and 35° CA ATDC, with soot reductions of 26.7%, −34.5%, and −112.8%, and NOx reductions of 5.88%, 21.2%, and 40.3%, respectively, for 1main+1post, 2main+1post, and 3main+1post injections.

A Computational Investigation of Piston Bowl Geometry and Injector Spray Pattern Effects on Gasoline Compression Ignition in a Heavy-Duty Diesel Engine

2019 ◽  
Author(s):  
Yu Zhang ◽  
Yuanjiang Pei ◽  
Meng Tang ◽  
Michael Traver
Keyword(s):  
Diesel Engine ◽  
Fuel Efficiency ◽  
Compression Ignition ◽  
Swirl Ratio ◽  
Heavy Duty ◽  
Load Range ◽  
Spray Pattern ◽  
Piston Bowl ◽  
Heavy Duty Diesel Engine ◽  
Heavy Duty Diesel

Abstract This study computationally investigates the potential of utilizing gasoline compression ignition (GCI) in a heavy-duty diesel engine to address a future ultra-low tailpipe NOx standard of 0.027 g/kWh while achieving high fuel efficiency. By conducting closed-cycle, full-geometry, 3-D computational fluid dynamics (CFD) combustion simulations, the effects of piston bowl geometry, injector spray pattern, and swirl ratio (SR) were investigated for a market gasoline. The simulations were performed at 1375 rpm over a load range from 5 to 15 bar BMEP. The engine compression ratio (CR) was increased from 15.7 used in previous work to 16.5 for this study. Two piston bowl concepts were studied with Design 1 attained by simply scaling from the baseline 15.7 CR piston bowl, and Design 2 exploring a wider and shallower combustion chamber design. The simulation results predicted that through a combination of the wider and shallower piston bowl design, a 14-hole injector spray pattern, and a swirl ratio of 1, Design 2 would lead to a 2–7% indicated specific fuel consumption (ISFC) improvement over the baseline by reducing the spray-wall interactions and lowering the in-cylinder heat transfer loss. Design 1 (10-hole and SR2) showed a more moderate ISFC reduction of 1–4% by increasing CR and the number of nozzle holes. The predicted fuel efficiency benefit of Design 2 was found to be more pronounced at low to medium loads.

scholarly journals Effects of renewable fuel and exhaust aftertreatment on primary and secondary emissions from a modern heavy-duty diesel engine

2021 ◽  
Vol 156 ◽  
pp. 105781
Author(s):  
Louise Gren ◽  
Vilhelm B. Malmborg ◽  
John Falk ◽  
Lassi Markula ◽  
Maja Novakovic ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Exhaust Aftertreatment ◽  
Heavy Duty ◽  
Renewable Fuel ◽  
Heavy Duty Diesel Engine ◽  
Heavy Duty Diesel

Fundamental Study of Waste Heat Recovery in the High Boosted 6-cylinder Heavy Duty Diesel Engine

2015 ◽  
Vol 8 (2) ◽  
pp. 209-226 ◽  
Author(s):  
Takuya Yamaguchi ◽  
Yuzo Aoyagi ◽  
Noboru Uchida ◽  
Akira Fukunaga ◽  
Masayuki Kobayashi ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Heavy Duty ◽  
Fundamental Study ◽  
Heavy Duty Diesel Engine ◽  
Heavy Duty Diesel
Sign in / Sign up

Export Citation Format

Share Document