Literature Data and Corrosion Testing of Hard Anodized and Duplex Sealed 7075-T7351 and 7050-T7451 Wrought Aluminum Alloy Plates after Cyclic Loading

2007 ◽  
Author(s):  
Winston Sequeira ◽  
Mike Jensen ◽  
Eric Peterson ◽  
Steve Thieman
Keyword(s):  
Aluminum Alloy ◽  
Cyclic Loading ◽  
Corrosion Testing ◽  
Wrought Aluminum

Mechanical Properties and Microstructure of Aluminum Alloy Al-6061 Obtained by the Liquid Forging Process

2010 ◽  
Vol 654-656 ◽  
pp. 1420-1423 ◽  
Author(s):  
Chun Wei Su ◽  
Peng Hooi Oon ◽  
Y.H. Bai ◽  
Anders W.E. Jarfors
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
Treatment Process ◽  
Forging Process ◽  
Al 6061 ◽  
Casting Alloys ◽  
Suitable Heat Treatment ◽  
Structural Applications ◽  
Wrought Aluminum

The liquid forging process has the flexibilities of casting in forming intricate profiles and features while imparting the liquid forged components with superior mechanical strength compared to similar components obtained via casting. Additionally, liquid forging requires significantly lower machine loads compared to solid forming processes. Currently, components that are formed by liquid forging are usually casting alloys of aluminum. This paper investigates the suitability of liquid forging a wrought aluminum alloy Al-6061 and the mechanical properties after forming. The proper handling of the Al-6061 alloy in its molten state is important in minimizing oxidation of its alloying elements. By maintaining the correct alloying composition of Al-6061 after liquid forging, these Al-6061 samples can subsequently undergo a suitable heat treatment process to significantly improve their yield strengths. Results show that the yield strengths of these liquid forged Al-6061 samples can be increased from about 90MPa, when they are in the as-liquid forged state, to about 275MPa after heat treatment. This improved yield strength is comparable to that of Al-6061 samples obtained by solid forming processes. As such, the liquid forging process here has been shown to be capable of forming wrought aluminum alloy components that has the potential for structural applications.

Ultrasonic assisted squeeze casting of a wrought aluminum alloy

2019 ◽  
Vol 266 ◽  
pp. 19-25 ◽  
Author(s):  
Gang Chen ◽  
Ming Yang ◽  
Yu Jin ◽  
Hongming Zhang ◽  
Fei Han ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Squeeze Casting ◽  
Ultrasonic Assisted ◽  
Wrought Aluminum

Simulation of 7050 Wrought Aluminum Alloy Wheel Die Forging and its Defects Analysis based on DEFORM

2010 ◽  
Author(s):  
Huang Shi-Quan ◽  
Yi You-Ping ◽  
Zhang Yu-Xun ◽  
F. Barlat ◽  
Y. H. Moon ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Die Forging ◽  
Alloy Wheel ◽  
Defects Analysis ◽  
Wrought Aluminum

scholarly journals Microstructure and mechanical properties of an ultrasonic spot welded aluminum alloy: the effect of welding energy

2021 ◽  
Author(s):  
He Peng ◽  
Daolun Chen ◽  
Xianquan Jiang
Keyword(s):  
Shear Strength ◽  
Aluminum Alloy ◽  
Cyclic Loading ◽  
Crack Growth ◽  
Failure Mode ◽  
Spot Welding ◽  
Energy Levels ◽  
Lap Shear Strength ◽  
Pull Out ◽  
Lap Shear

The aim of this study is to evaluate the microstructures, tensile lap shear strength, and fatigue resistance of 6022-T43 aluminum alloy joints welded via a solid-state welding technique–ultrasonic spot welding (USW)–at different energy levels. An ultra-fine necklace-like equiaxed grain structure is observed along the weld line due to the occurrence of dynamic crystallization, with smaller grain sizes at lower levels of welding energy. The tensile lap shear strength, failure energy, and critical stress intensity of the welded joints first increase, reach their maximum values, and then decrease with increasing welding energy. The tensile lap shear failure mode changes from interfacial fracture at lower energy levels, to nugget pull-out at intermediate optimal energy levels, and to transverse through-thickness (TTT) crack growth at higher energy levels. The fatigue life is longer for the joints welded at an energy of 1400 J than 2000 J at higher cyclic loading levels. The fatigue failure mode changes from nugget pull-out to TTT crack growth with decreasing cyclic loading for the joints welded at 1400 J, while TTT crack growth mode remains at all cyclic loading levels for the joints welded at 2000 J. Fatigue crack basically initiates from the nugget edge, and propagates with “river-flow” patterns and characteristic fatigue striations. Keywords: aluminum alloy; ultrasonic spot welding; EBSD; microstructure; tensile strength; fatigue

scholarly journals Experimental Investigation and Optimization of the Semisolid Multicavity Squeeze Casting Process for Wrought Aluminum Alloy Scroll

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5278
Author(s):  
Yi Guo ◽  
Yongfei Wang ◽  
Shengdun Zhao
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Process Parameters ◽  
Squeeze Casting ◽  
Shrinkage Porosity ◽  
Optimal Process ◽  
Squeeze Pressure ◽  
Wrought Aluminum

Scroll compressors are popularly applied in air-conditioning systems. The conventional fabrication process causes gas and shrinkage porosity in the scroll. In this paper, the electromagnetic stirring (EMS)-based semisolid multicavity squeeze casting (SMSC) process is proposed for effectively manufacturing wrought aluminum alloy scrolls. Insulation temperature, squeeze pressure, and the treatment of the micromorphology and mechanical properties of the scroll were investigated experimentally. It was found that reducing the insulation temperature can decrease the grain size, increase the shape factor, and improve mechanical properties. The minimum grain size was found as 111 ± 3 μm at the insulation temperature of 595 °C. The maximum tensile strength, yield strength, and hardness were observed as 386 ± 8 MPa, 228 ± 5 MPa, and 117 ± 5 HV, respectively, at the squeeze pressure of 100 MPa. The tensile strength and hardness of the scroll could be improved, and the elongation was reduced by the T6 heat treatment. The optimal process parameters are recommended at an insulation temperature in the range of 595–600 °C and a squeeze pressure of 100 MPa. Under the optimal process parameters, scroll casting was completely filled, and there was no obvious shrinkage defect observed inside. Its microstructure is composed of fine and spherical grains.

scholarly journals Micro drilling of 5056 wrought aluminum alloy.

1994 ◽  
Vol 44 (9) ◽  
pp. 486-491 ◽  
Author(s):  
Makoto OGAWA ◽  
Mitsuru INOSE ◽  
Minoru ARAI ◽  
Tsuneo SAGA
Keyword(s):  
Aluminum Alloy ◽  
Micro Drilling ◽  
Wrought Aluminum
Sign in / Sign up

Export Citation Format

Share Document