Partially Pre-Mixed Auto-Ignition of Gasoline to Attain Low Smoke and Low NOx at High Load in a Compression Ignition Engine and Comparison with a Diesel Fuel

2007 ◽  
Author(s):  
Gautam T. Kalghatgi ◽  
Per Risberg ◽  
Hans-Erik Angstrom
Keyword(s):  
Diesel Fuel ◽  
High Load ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Auto Ignition

Effect of Premixed Diesel Fuel on Partial HCCI Combustion Characteristics

2014 ◽  
Vol 663 ◽  
pp. 26-33
Author(s):  
Y.H. Teoh ◽  
H.H. Masjuki ◽  
M.A. Kalam ◽  
Muhammad Afifi Amalina ◽  
H.G. How
Keyword(s):  
Diesel Fuel ◽  
Engine Speed ◽  
Direct Injection ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Hcci Combustion ◽  
Light Duty ◽  
Auto Ignition ◽  
Ignition Characteristics

This study investigated the effects of premixed diesel fuel on the auto-ignition characteristics in a light duty compression ignition engine. A partial homogeneous chargecompression ignition (HCCI) engine was modified from a single cylinder, four-stroke, direct injection compression ignition engine. The partial HCCI is achieved by injecting diesel fuel into the intake port of the engine, while maintaining diesel fuel injected in cylinder for combustion triggering. The auto-ignition of diesel fuel has been studied at various premixed ratios from 0 to 0.60, under engine speed of 1600 rpm and 20Nm load. The results for performance, emissions and combustion were compared with those achieved without premixed fuel. From the heat release rate (HRR) profile which was calculated from in-cylinder pressure, it is clearly observed that two-stage and three-stage ignition were occurred in some of the cases. Besides, the increases of premixed ratio to some extent have significantly reduced in NO emission.

scholarly journals A Multicomponent Blend as a Diesel Fuel Surrogate for Compression Ignition Engine Applications

2015 ◽  
Vol 137 (11) ◽  
Author(s):  
Yuanjiang Pei ◽  
Marco Mehl ◽  
Wei Liu ◽  
Tianfeng Lu ◽  
William J. Pitz ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Flow Reactor ◽  
Expert Knowledge ◽  
Combustion Model ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Combined Mechanism ◽  
Fuel Surrogate ◽  
Skeletal Mechanism

A mixture of n-dodecane and m-xylene is investigated as a diesel fuel surrogate for compression ignition (CI) engine applications. Compared to neat n-dodecane, this binary mixture is more representative of diesel fuel because it contains an alkyl-benzene which represents an important chemical class present in diesel fuels. A detailed multicomponent mechanism for n-dodecane and m-xylene was developed by combining a previously developed n-dodecane mechanism with a recently developed mechanism for xylenes. The xylene mechanism is shown to reproduce experimental ignition data from a rapid compression machine (RCM) and shock tube (ST), speciation data from the jet stirred reactor and flame speed data. This combined mechanism was validated by comparing predictions from the model with experimental data for ignition in STs and for reactivity in a flow reactor. The combined mechanism, consisting of 2885 species and 11,754 reactions, was reduced to a skeletal mechanism consisting 163 species and 887 reactions for 3D diesel engine simulations. The mechanism reduction was performed using directed relation graph (DRG) with expert knowledge (DRG-X) and DRG-aided sensitivity analysis (DRGASA) at a fixed fuel composition of 77% of n-dodecane and 23% m-xylene by volume. The sample space for the reduction covered pressure of 1–80 bar, equivalence ratio of 0.5–2.0, and initial temperature of 700–1600 K for ignition. The skeletal mechanism was compared with the detailed mechanism for ignition and flow reactor predictions. Finally, the skeletal mechanism was validated against a spray flame dataset under diesel engine conditions documented on the engine combustion network (ECN) website. These multidimensional simulations were performed using a representative interactive flame (RIF) turbulent combustion model. Encouraging results were obtained compared to the experiments with regard to the predictions of ignition delay and lift-off length at different ambient temperatures.

COMBUSTION AND EMISSIONS CHARACTERISTICS OF A COMPRESSION IGNITION ENGINE FUELLED WITH N-BUTANOL BLENDS

2015 ◽  
Vol 77 (8) ◽  
Author(s):  
I. M. Yusri ◽  
M. K. Akasyah ◽  
R. Mamat ◽  
O. M. Ali
Keyword(s):  
Diesel Fuel ◽  
Engine Speed ◽  
Energy Content ◽  
Direct Injection ◽  
Cetane Number ◽  
Injection System ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Exhaust Temperature ◽  
Blended Fuels

The use of biomass based renewable fuel, n-butanol blends for compression ignition (CI) engine has attracted wide attention due to its superior properties such as better miscibility, higher energy content, and cetane number as compared to other alternatives fuel. In this present study the use of n-butanol 10% blends (Bu10) with diesel fuel has been tested using multi-cylinder, 4-stroke engine with common rail direct injection system to investigate the combustion and emissions of the blended fuels. Based on the tested engine at BMEP=3.5Bar. Based on the results Bu10 fuel indicates lower first and second peak pressure by 5.4% and 2.4% for engine speed 1000rpm and 4.4% and 2.1% for engine speed 2500rpm compared to diesel fuel respectively. Percentage reduction relative to diesel fuel at engine speeds 1000rpm and 2500rpm for Bu10: Exhaust temperature was 7.5% and 5.2% respectively; Nitrogen oxides (NOx) 73.4% and 11.3% respectively.

Chemical and spectroscopic studies of blue flames in the auto-ignition of methane

1955 ◽  
Vol 230 (1180) ◽  
pp. 1-19 ◽  
Keyword(s):  
Spectroscopic Studies ◽  
Compression Ignition ◽  
Low Temperature Oxidation ◽  
Compression Ignition Engine ◽  
Temperature Oxidation ◽  
Carbon Particles ◽  
Cool Flames ◽  
Auto Ignition ◽  
Increasing Temperature ◽  
Normal Flame

A blue pre-ignition glow has been found with weak methane + air mixtures, using a motored compression-ignition engine with fixed compression ratio and speed; the temperature was controlled by preheating the inlet air. The limits of the glow and its transition to normal flame have been studied. Analyses of exhaust products and records of pressure and luminosity have been made. The spectrum of the glow shows formaldehyde bands, normally associated with cool flames. As the normal ignition limit is approached this spectrum changes smoothly, with increasing temperature or mixture strength, to a normal flame spectrum showing OH, CH and HCO bands. Using a stroboscope we have found slight indication that the CH 2 O bands precede the CH and OH. Less lean mixtures show yellow luminosity, associated with carbon particles. The possibilities that the CH 2 O emission results from polymerization of the methane, from partial oxidation to methyl alcohol, or directly from a cool-flame phenomenon in methane, are discussed in relation to conditions in the combustion chamber. The new observation of CH 2 O bands from methane may be interpreted in favour of its formation by reactions of methoxy radicals. Methane is known to knock in an engine at high compression ratios. Present results suggest that low-temperature oxidation processes may, as with other hydrocarbons, contribute to this knock.

Sign in / Sign up

Export Citation Format

Share Document