The Characteristic of Transient HC Emissions of the First Firing Cycle During Cold Start on an LPG SI Engine

2006 ◽  
Author(s):  
Liguang Li ◽  
Ligong ◽  
Dongping Qiu ◽  
Zhimin Liu
Keyword(s):  
Cold Start ◽  
Firing Cycle ◽  
Si Engine ◽  
Hc Emissions

HiL-Calibration of SI Engine Cold Start and Warm-Up Using Neural Real-Time Model

2004 ◽  
Author(s):  
Thomas Winsel ◽  
Mohamed Ayeb ◽  
Heinz J. Theuerkauf ◽  
Stefan Pischinger ◽  
Christof Schernus ◽  
...  
Keyword(s):  
Real Time ◽  
Cold Start ◽  
Si Engine ◽  
Time Model ◽  
Warm Up

Airless In-Line Adsorber System for Reducing Cold Start HC Emissions

1998 ◽  
Author(s):  
M. D. Patil ◽  
Y. Lisa Peng ◽  
Kathleen E. Morse
Keyword(s):  
Cold Start ◽  
Hc Emissions

scholarly journals Study on the Effect of Second Injection Timing on the Engine Performances of a Gasoline/Hydrogen SI Engine with Split Hydrogen Direct Injecting

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5223
Author(s):  
Guanting Li ◽  
Xiumin Yu ◽  
Ping Sun ◽  
Decheng Li
Keyword(s):  
Numerical Study ◽  
Direct Injection ◽  
Mixture Distribution ◽  
Spark Ignition ◽  
Injection Timing ◽  
Si Engine ◽  
Excess Air ◽  
Crank Angle ◽  
Hc Emissions ◽  
Main Factor

Split hydrogen direct injection (SHDI) has been proved capable of better efficiency and fewer emissions. Therefore, to investigate SHDI deeply, a numerical study on the effect of second injection timing was presented at a gasoline/hydrogen spark ignition (SI) engine with SHDI. With an excess air ratio of 1.5, five different second injection timings achieved five kinds of hydrogen mixture distribution (HMD), which was the main factor affecting the engine performances. With SHDI, since the HMD is manageable, the engine can achieve better efficiency and fewer emissions. When the second injection timing was 105° crank angle (CA) before top dead center (BTDC), the Pmax was the highest and the position of the Pmax was the earliest. Compared with the single hydrogen direct injection (HDI), the NOX, CO and HC emissions with SHDI were reduced by 20%, 40% and 72% respectively.

Investigation of a Novel Fuel Injection Technology Aimed to Reduce Cold-Start Emissions in SI Engines

2002 ◽  
Author(s):  
Brian T. Reese ◽  
Yann G. Guezennec ◽  
Miodrag Oljaca
Keyword(s):  
Fuel Injection ◽  
Cold Start ◽  
Operating Conditions ◽  
The Novel ◽  
Fuel Injector ◽  
Si Engine ◽  
Fuel Droplets ◽  
Si Engines ◽  
Atomization Characteristics ◽  
Injection Technology

A novel fuel atomization device (Nanomiser™) was evaluated under laboratory conditions with respect to its ability to reduce SI engine cold-start hydrocarbon emissions. First, comparisons between the level of atomization using the conventional, pintle-type fuel injector and the novel atomizer were carried out using flow visualization in a spray chamber and particle size distribution. The novel atomizer is capable of producing sub-micron fuel droplets, which form an ultra-fine mist with outstanding non-wetting characteristics. To capitalize on these atomization characteristics, this device was compared to a conventional fuel injector in a small, two-cylinder, SI engine under a number of operating conditions. Results show a slightly enhanced combustion quality and lean limit under warm operating conditions and a dramatic reduction in unburned HC emission under cold operating conditions, with cold emissions with the Nanomiser™ matching those with a conventional injector under fully warm conditions.

Speciated Hydrocarbon Emissions of SI Engine During Cold Start and Warm-up

1993 ◽  
Author(s):  
Shuichi Kubo ◽  
Masami Yamamoto ◽  
Yoshimi Kizaki ◽  
Satoshi Yamazaki ◽  
Toshiaki Tanaka ◽  
...  
Keyword(s):  
Cold Start ◽  
Hydrocarbon Emissions ◽  
Si Engine ◽  
Warm Up

Cold-Start Emissions of an SI Engine Using Butanol/Gasoline Blends

2014 ◽  
Vol 977 ◽  
pp. 47-50
Author(s):  
Mei Yu Shi ◽  
Rong Fu Zhu ◽  
Jiang Li ◽  
Yuan Tao Sun
Keyword(s):  
Low Temperature ◽  
Cold Start ◽  
Fuel Mixture ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Experimental Results ◽  
Si Engine

The influence of butanol/gasoline blends at low temperature for-7°C, on cold-start emissions of a spark-ignition engine was tested. In cold-start period of the engine, the efficiency of the engine was expected to be poor, and the air/fuel mixture would be leaner for the more butanol added. The experimental results showed that the engine could be stable with B10 and B30 in cold-start, and HC and CO emissions reduced more significantly with more butanol added.

Early Model-Based Design and Verification of Automotive Control System Software Implementations

2014 ◽  
Vol 137 (2) ◽  
Author(s):  
Mahdi Shahbakhti ◽  
Mohammad Reza Amini ◽  
Jimmy Li ◽  
Satoshi Asami ◽  
J. Karl Hedrick
Keyword(s):  
Controller Design ◽  
Combustion Engine ◽  
Control Unit ◽  
Cold Start ◽  
Early Model ◽  
Automotive Control ◽  
Model Based ◽  
Numerical Noise ◽  
Software Implementations ◽  
Hc Emissions

Verification and validation (V&V) are essential stages in the design cycle of automotive controllers to remove the gap between the designed and implemented controller. In this paper, an early model-based methodology is proposed to reduce the V&V time and improve the robustness of the designed controllers. The application of the proposed methodology is demonstrated on a cold start emission control problem in a midsize passenger car. A nonlinear reduced order model-based controller based on singular perturbation approximation (SPA) is designed to reduce cold start hydrocarbon (HC) emissions from a spark ignition (SI) combustion engine. A model-based simulation platform is created to verify the controller robustness against sampling, quantization, and fixed-point arithmetic imprecision. In addition, the results from early model-based verification are used to identify and remove sources of errors causing propagation of numerical imprecision in the controller structure. Thus the structure of the controller is modified to avoid or to reduce the level of numerical noise in the controller design. The performance of the final modified controller is validated in real-time by testing the control algorithm on a real engine control unit. The validation results indicate the modified controller is 17–63% more robust to different implementation imprecision while it requires lower implementation cost. The proposed methodology from this paper is expected to reduce typical V&V efforts in the development of automotive controllers.

scholarly journals Investigation of cylinder corrosion mechanism of gasoline SI engine by corrosion experiments under the conditions of cold start with EGR.

2020 ◽  
Vol 2020 (0) ◽  
pp. J07112
Author(s):  
Kohei MORIE ◽  
Ryuusei KOUDA ◽  
Satoshi SAKAIDA ◽  
Kotaro TANAKA ◽  
Mitsuru KONNO ◽  
...  
Keyword(s):  
Cold Start ◽  
Corrosion Mechanism ◽  
Si Engine
Sign in / Sign up

Export Citation Format

Share Document