Effect of Injection Pressure and Split Injection on Exhaust Odor and Engine Noise in DI Diesel Engines

2002 ◽  
Author(s):  
Murari Mohon Roy ◽  
Hideyuki Tsunemoto
Keyword(s):  
Diesel Engines ◽  
Injection Pressure ◽  
Split Injection ◽  
Engine Noise

scholarly journals Optimization of Fuel Injection Parameters of Moringa oleifera Biodiesel-Diesel Blend for Engine-Out-Responses Improvements

Symmetry ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 982
Author(s):  
Yew Heng Teoh ◽  
Heoy Geok How ◽  
Farooq Sher ◽  
Thanh Danh Le ◽  
Hwai Chyuan Ong ◽  
...  
Keyword(s):  
Diesel Engines ◽  
Fossil Fuels ◽  
Moringa Oleifera ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Single Step ◽  
Rapid Decline ◽  
Fuel Blend ◽  
Combustion Dynamics ◽  
Rsm Optimization

Biodiesel has gained popularity in diesel engines as a result of the rapid decline of fossil fuels and population growth. The processing of biodiesel from non-edible Moringa Oleifera was investigated using a single-step transesterification technique. Both fuels had their key physicochemical properties measured and investigated. In a common-rail diesel engine, the effects of MB50 fuel blend on the symmetric characteristics of engine-out responses were evaluated under five load settings and at 1000 rpm. As compared to standard diesel, MB50 increased brake thermal efficiency (BTE), and nitrogen oxides (NOx) emissions while lowering brake specific fuel consumption (BSFC), and smoke emissions for all engine loads. A further study of injection pressure and start of injection (SOI) timing for MB50 fuel was optimized using response surface methodology (RSM). The RSM optimization resulted in improved combustion dynamics due to symmetry operating parameters, resulting in a simultaneous decrease in NOx and smoke emissions without sacrificing BTE. RSM is an efficient optimization method for achieving optimal fuel injection parameter settings, as can be deduced. As a result, a clearer understanding of the use of MB50 fuel in diesel engines can be given, allowing for the best possible engine efficiency.

The performance and emission characteristics of emulsified fuel in a direct injection diesel engine

2007 ◽  
Vol 221 (7) ◽  
pp. 893-900 ◽  
Author(s):  
M P Ashok ◽  
C G Saravanan
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Injection Pressure ◽  
Alternative Fuel ◽  
Experimental Investigations ◽  
Maximum Speed ◽  
Power Sources ◽  
Performance And Emission ◽  
Emulsified Fuel

Diesel engines are employed as the major propulsion power sources because of their simple, robust structure and high fuel economy. It is expected that diesel engines will be widely used in the foreseeable future. However, an increase in the use of diesel engines causes a shortage of fossil fuel and results in a greater degree of pollution. To regulate the above, identifying an alternative fuel to the diesel engine with less pollution is essential. Ethanol–diesel emulsion is one such method, used for the preparation of an alternative fuel for the diesel engine. Experimental investigations were carried out to compare the performance of diesel fuel with different ratios 50D: 50E (50 per cent diesel No: 2: 50 per cent ethanol –100 per cent proof) and 60D: 40E emulsified fuels. In the next phase, experiments were conducted for the selected emulsified fuel ratio 50D: 50E for different high injection pressures and the results are compared. The results show that for the emulsified fuel ratios, there is a marginal increase in torque, power, NO x, emissions, and decreasing values of carbon monoxide (CO), sulphur dioxide (SO2) emissions at the maximum speed conditions, compared with diesel fuel. Also, it is found that an increase in injection pressure of the engine running with emulsified fuel decreases CO and smoke emissions especially between 1500 to 2000 r/min with respect to the diesel fuel.

Effect of Injection Pressure with Split Injection in a V6 Diesel Engine

2009 ◽  
Author(s):  
Nik Rosli Abdullah ◽  
Rizalman Mamat ◽  
P. Rounce ◽  
A. Tsolakis ◽  
M. L. Wyszynski ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Injection Pressure ◽  
Split Injection

A Study on the Applicability of Straight Vegetable Oils to Medium Speed Diesel Engines

2009 ◽  
Author(s):  
Hyoung-Keun Park ◽  
Sang-Hak Ghal ◽  
Tae-Hyung Park ◽  
Yong-Hee Ahn ◽  
Sung-Hyeok Kim
Keyword(s):  
Vegetable Oil ◽  
Diesel Engines ◽  
Short Interval ◽  
Injection Pressure ◽  
Acid Number ◽  
Fuel Oil ◽  
Oil Consumption ◽  
Total Acid ◽  
Medium Speed ◽  
Marine Diesel

Straight vegetable oil (SVO) fuels such as palm oil, animal fat oil and waste vegetable oil were tested as fuels in a single-cylinder diesel engine to evaluate applicability to medium-speed diesel engines. Fuel-related properties of the SVO were assessed and compared with conventional marine diesel fuel oil (MDO). The total acid number (TAN) of the SVO fuels changed during a short interval in a drying oven which heated the SVO fuels to 170 degrees Celsius for several weeks. The SVO have not gone rancid any further after reaching limit. And the TAN of the SVO fuels was not related to corrosion of the parts. The SVO fuels needed to be heated to an appropriate temperature to use as fuel of the engine since the SVO fuels are more viscous than conventional diesel fuels. Both the injection period and the injection pressure increased due to low heating values of the SVO fuels. By the same token, fuel oil consumption increased over 10%. The overall exhaust emissions were lower with the SVO fuels, but NOx emission was as much as MDO at the higher loads.

Comparison of Three Types of Common Rail Systems Suited for Diesel Engines From 1 to 5 Megawatt

2006 ◽  
Author(s):  
Marco Ganser ◽  
Ulrich Moser
Keyword(s):  
Diesel Engines ◽  
Pressure Wave ◽  
Dynamic Pressure ◽  
Injection Pressure ◽  
Injection Rate ◽  
Common Rail ◽  
Wave Dynamics ◽  
Rail Systems ◽  
Heavy Duty Diesel ◽  
The Individual

The basic physical law governing the injection in Common Rail Systems is the compressibility of the fuel. The effects of pressure wave dynamics, the layout of the system volume and its geometrical distribution strongly affect the injection events at every injector. In this Paper, three different arrangements of system volumes and their effect upon the performance of the individual injectors are compared using the hydraulics simulation tool AMESim. Two systems are known in the passenger car and the heavy duty diesel engine domains. The third system is new and takes advantage of pressure wave dynamics to tailor the injection event. This system is best suited for Diesel Engines with a power from 1 to 5 MW, as used in locomotives, ships, power generation and heavy earthmoving machinery. It produces a more favorable pattern of the injection pressure and injection rate shape during any injection event by hydraulically interconnecting the individual injector’s accumulators during the injection and taking advantage of pressure wave dynamics. Right after the end of each injection, dynamic pressure pulsations are evened out with a dampening device. A multi-cylinder system provides equal conditions for all injections. Its very simple design and increased performance makes the novel system of very attractive use in the above mentioned fields.

Direct Water Injection to Improve Diesel Spray Combustion

2003 ◽  
Author(s):  
Koji Takasaki ◽  
Tatsuo Takaishi ◽  
Hiroyuki Ishida ◽  
Keijirou Tayama
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Fuel Injection ◽  
Nox Reduction ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection System ◽  
Injection Hole ◽  
Low Speed ◽  
Direct Water Injection

Now, it is essential to apply some measures for NOx reduction to low-speed diesel engines emitting much more NOx than high-speed engines. At the same time PM emission must be reduced especially when bunker fuel or heavy fuel is burned. This paper describes the applications of SFWI (Stratified Fuel Water Injection) system and DWI (Direct Water Injection) system to large sized diesel engines to reduce NOx and PM emission. SFWI system makes it possible to inject water during fuel injection from the same nozzle hole without mixing the liquids. DWI system injects water with high injection pressure from the other injection hole than the fuel injection hole into the combustion chamber directly. For testing both the systems, a 2-stroke-cycle low-speed test engine was used.

Experimental Stand to Investigate the Injection Process in Diesel Engines

2021 ◽  
Vol 42 ◽  
pp. 79-84
Author(s):  
Dragoș Tutunea ◽  
Ilie Dumitru ◽  
Laurenţiu Racilă
Keyword(s):  
Diesel Engines ◽  
Electric Motor ◽  
High Performance ◽  
Fuel Injection ◽  
Combustion Process ◽  
Injection Pressure ◽  
Injection System ◽  
Injection Process ◽  
Experimental Stand ◽  
Fuel Injection Pressure

The objective of this paper is to investigate the fuel injection system in diesel engines by using inline pumps. In a diesel engines, the fuel injection pressure plays an important role in the combustion process in order to obtain high performance and low fuel consumption. The experiments in this paper are been performed on a 6 cylinder inline pump which is actioned by an electric motor with variable r.p.m.-s The quantity of the fuel injected by each injector is measured function of time and the speed of electric motor. The experiments show the degree of non-uniformity of the fuel delivered by the pump to injectors.

Sign in / Sign up

Export Citation Format

Share Document