Performance Simulation of a Compression Ignition Free Piston Engine

2001 ◽  
Author(s):  
Martti Larmi ◽  
Sten Isaksson ◽  
Seppo Tikkanen ◽  
Mika Lammila
Keyword(s):  
Compression Ignition ◽  
Piston Engine ◽  
Free Piston ◽  
Performance Simulation ◽  
Free Piston Engine

scholarly journals Influence of hydrogen as a fuel additive on combustion and emissions characteristics of a free piston engine

2020 ◽  
Vol 24 (1 Part A) ◽  
pp. 87-99
Author(s):  
Mohammad Alrbai ◽  
Bashar Qawasmeh ◽  
Sameer Al-Dahidi ◽  
Osama Ayadi
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Ignition Delay ◽  
Combustion Characteristics ◽  
Fuel Additive ◽  
Compression Ignition ◽  
Piston Engine ◽  
Free Piston ◽  
Free Piston Engine

It has been shown that using fuel additives play an important role in enhancing the combustion characteristics in terms of efficiency and emissions. In addition, free piston engines have shown capable in reducing energy losses and presenting more efficient and reliable engines. In this context, the objective of the present work is to investigate the effect of using hydrogen as a fuel additive in natural gas homogeneous charge compression ignition free piston engine. To this aim, two models have been iteratively coupled: the combustion model that is used to calculate the heat release of the combustion and the scavenging model that is employed to determine the in-cylinder mixture state after scavenging in terms of its homogeneity and species mass fractions and to obtain the finial pressure and temperature of the in-cylinder mixture. In the former model, the 0-D approach through Cantera toolkit has been considered due to the fact that homogeneous charge compression ignition combustion is very rapid and the fuel-air mixture is well-homogenous, whereas in the latter model, 3-D-CFD approach through AN-SYS FLUENT software is considered to ensure precise calculations of the species exchange at the end of each engine cycle. The effect of hydrogen as a fuel additive has been quantified in terms of the combustion characteristics (e. g., ignition delay, heat release rate, engine overall efficiency and emissions, etc.). It has been shown that hydrogen addition reduces ignition delay time, decreases the in-cylinder peak pressure, while allowing the engine to operate with higher mechanical efficiency as it has high heat release rate, increases the NOx emission levels of the engine, but decreases the CO levels

Motion Characteristics and Influence Factors of Piston Assembly in a Compression-Ignition Hydraulic Free-Piston Engine

2013 ◽  
Vol 860-863 ◽  
pp. 1761-1765
Author(s):  
Ying Xiao Yu ◽  
Zhao Cheng Yuan ◽  
Jia Yi Ma ◽  
Shi Yu Li
Keyword(s):  
Fuel Injection ◽  
Influence Factors ◽  
Basic Structure ◽  
Injection Timing ◽  
Compression Ignition ◽  
Piston Engine ◽  
Free Piston ◽  
Free Piston Engine ◽  
Motion Characteristics ◽  
Piston Assembly

The advantages and basic structure of hydraulic free-piston engine (HFPE) were presented. And the operation principle of a single piston compression-ignition HFPE was analyzed. Based on the basic theory of thermodynamics, hydraulic fluid mechanics and dynamics, the system simulation model for a single-piston compression-ignition HFPE was established in the environment of MATLAB/SIMULINK. The simulation results, which accord with the related literature data, indicate that the asymmetric characteristics of piston motion in the entire cycle are very obvious, the compression stroke duration is longer than the expansion stroke, the time at around the top dead center (TDC) is short. The piston assembly motion is a process when the energy balance is fulfilled, and some factors must be taken into account for design optimization, such as the piston assembly mass, compression accumulator pressure, fuel injection timing and fuel injection quantity.

scholarly journals Research on the Operating Characteristics of Hydraulic Free-Piston Engines: A Systematic Review and Meta-Analysis

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3530
Author(s):  
Fukang Ma ◽  
Shuanlu Zhang ◽  
Zhenfeng Zhao ◽  
Yifang Wang
Keyword(s):  
Systematic Review ◽  
High Efficiency ◽  
Meta Analysis ◽  
Combustion Process ◽  
Research Progress ◽  
Future Research ◽  
Operating Characteristics ◽  
Piston Engine ◽  
Free Piston ◽  
Free Piston Engine

The hydraulic free-piston engine (HFPE) is a kind of hybrid-powered machine which combines the reciprocating piston-type internal combustion engine and the plunger pump as a whole. In recent years, the HFPE has been investigated by a number of research groups worldwide due to its potential advantages of high efficiency, energy savings, reduced emissions and multi-fuel operation. Therefore, our study aimed to assess the operating characteristics, core questions and research progress of HFPEs via a systematic review and meta-analysis. We included operational control, starting characteristics, misfire characteristics, in-cylinder working processes and operating stability. We conducted the literature search using electronic databases. The research on HFPEs has mainly concentrated on four kinds of free-piston engine, according to piston arrangement form: single piston, dual pistons, opposed pistons and four-cylinder complex configuration. HFPE research in China is mainly conducted in Zhejiang University, Tianjin University, Jilin University and the Beijing Institute of Technology. In addition, in China, research has mainly focused on the in-cylinder combustion process while a piston is free by considering in-cylinder combustion machinery and piston dynamics. Regarding future research, it is very important that we solve the instabilities brought about by chance fluctuations in the combustion process, which will involve the hydraulic system’s efficiency, the cyclical variation, the method of predicting instability and the recovery after instability.

Sign in / Sign up

Export Citation Format

Share Document