Spectroscopic Investigation of the Combustion Process in an LPG Lean-burn SI Engine

1999 ◽  
Author(s):  
Daeyup Lee ◽  
Shinichi Goto ◽  
Insu Kim ◽  
Masamitsu Motohashi
Keyword(s):  
Spectroscopic Investigation ◽  
Combustion Process ◽  
Si Engine ◽  
Lean Burn

scholarly journals Effect of Fuel and Air Dilution on Syngas Combustion in an Optical SI Engine

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1566 ◽  
Author(s):  
S.D. Martinez-Boggio ◽  
S.S. Merola ◽  
P. Teixeira Lacava ◽  
A. Irimescu ◽  
P.L. Curto-Risso
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Process ◽  
Visible Spectrum ◽  
Propagation Speed ◽  
Fuel Mixture ◽  
Operating Conditions ◽  
Inert Gases ◽  
Pollutant Emissions ◽  
Si Engine ◽  
Lean Burn

To mitigate the increasing concentration of carbon dioxide in the atmosphere, energy production processes must change from fossil to renewable resources. Bioenergy utilization from agricultural residues can be a step towards achieving this goal. Syngas (fuel obtained from biomass gasification) has been proved to have the potential of replacing fossil fuels in stationary internal combustion engines (ICEs). The processes associated with switching from traditional fuels to alternatives have always led to intense research efforts in order to have a broad understanding of the behavior of the engine in all operating conditions. In particular, attention needs to be focused on fuels containing relatively high concentrations of hydrogen, due to its faster propagation speed with respect to traditional fossil energy sources. Therefore, a combustion study was performed in a research optical SI engine, for a comparison between a well-established fuel such as methane (the main component of natural gas) and syngas. The main goal of this work is to study the effect of inert gases in the fuel mixture and that of air dilution during lean fuelling. Thus, two pure syngas blends (mixtures of CO and H2) and their respective diluted mixtures (CO and H2 with 50vol% of inert gases, CO2 and N2) were tested in several air-fuel ratios (stoichiometric to lean burn conditions). Initially, the combustion process was studied in detail by traditional thermodynamic analysis and then optical diagnostics were applied thanks to the optical access through the piston crown. Specifically, images were taken in the UV-visible spectrum of the entire cycle to follow the propagation of the flame front. The results show that hydrogen promotes flame propagation and reduces its distortion, as well as resulting in flames evolving closer to the spark plug. All syngas blends show a stable combustion process, even in conditions of high air and fuel dilution. In the leanest case, real syngas mixtures present a decrease in terms of performance due to significant reduction in volumetric efficiency. However, this condition strongly decreases pollutant emissions, with nitrogen oxide (NOx) concentrations almost negligible.

Numerical investigation the effects of the twin-spark plugs coupled with EGR on the combustion process and emissions characteristics in a lean burn natural gas SI engine

Energy ◽  
2020 ◽  
Vol 206 ◽  
pp. 118181 ◽  
Author(s):  
Xiongbo Duan ◽  
Shiheng Zhang ◽  
Yiqun Liu ◽  
Yangtang Li ◽  
Jingping Liu ◽  
...  
Keyword(s):  
Natural Gas ◽  
Numerical Investigation ◽  
Combustion Process ◽  
Si Engine ◽  
Lean Burn

A Control-Oriented Reaction-Based SI Engine Combustion Model

2018 ◽  
Author(s):  
Ruixue C. Li ◽  
Guoming G. Zhu
Keyword(s):  
Chemical Reaction ◽  
Mass Fraction ◽  
Combustion Process ◽  
Combustion Model ◽  
Spark Ignition Engines ◽  
Si Engine ◽  
Chemical Reaction Mechanism ◽  
Engine Combustion ◽  
Rate Of Heat Release ◽  
Mass And Heat Transfer

This paper proposes a control-oriented chemical reaction-based two-zone combustion model designed to accurately describe the combustion process and thermal performance for spark-ignition engines. The combustion chamber is assumed to be divided into two zones: reaction and unburned zones, where the chemical reaction takes place in the reaction zone and the unburned zone contains all the unburned mixture. In contrast to the empirical pre-determined Wiebe-function-based combustion model, an ideal two-step chemical reaction mechanism is used to reliably model the detailed combustion process such as mass-fraction-burned (MFB) and rate of heat release. The interaction between two zones includes mass and heat transfer at the zone interface to have a smooth combustion process. This control-oriented model is extensively calibrated based on the experimental data to demonstrate its capability of predicting the combustion process and thermodynamic states of the in-cylinder mixture.

scholarly journals Prechamber optimal selection for a two stage turbulent jet ignition type combustion system in CNG-fuelled engine

2019 ◽  
Vol 176 (1) ◽  
pp. 16-26 ◽  
Author(s):  
Ireneusz PIELECHA ◽  
Wojciech BUESCHKE ◽  
Maciej SKOWRON ◽  
Łukasz FIEDKIEWICZ ◽  
Filip SZWAJCA ◽  
...  
Keyword(s):  
High Speed ◽  
Internal Combustion Engines ◽  
Combustion Process ◽  
Optimization Methods ◽  
Turbulent Jet ◽  
Experimental Investigations ◽  
Combustion System ◽  
Two Stage ◽  
Lean Burn ◽  
High Speed Engine

Searching for further reduction of fuel consumption simultaneously with the reduction of toxic compounds emission new systems for lean-mixture combustion for SI engines are being discussed by many manufacturers. Within the European GasOn-Project (Gas Only Internal Combustion Engines) the two-stage combustion and Turbulent Jet Ignition concept for CNG-fuelled high speed engine has been proposed and thoroughly investigated where the reduction of gas consumption and increasing of engine efficiency together with the reduction of emission, especially CO2 was expected. In the investigated cases the lean-burn combustion process was conducted with selection of the most effective pre-combustion chamber. The experimental investigations have been performed on single-cylinder AVL5804 research engine, which has been modified to SI and CNG fuelling. For the analysis of the thermodynamic, operational and emission indexes very advanced equipment has been applied. Based on the measuring results achieved for different pre-chamber config-urations the extended methodology of polioptimization by pre-chamber selection and the shape of main chamber in the piston crown for proposed combustion system has been described and discussed. The results of the three versions of the optimization methods have been comparatively summarized in conclusions.

Investigation of combustion and emissions of an SI engine with ethanol port injection and gasoline direct injection under lean burn conditions

Energy ◽  
2019 ◽  
Vol 189 ◽  
pp. 116231 ◽  
Author(s):  
Xiumin Yu ◽  
Zezhou Guo ◽  
Ping Sun ◽  
Sen Wang ◽  
Anshi Li ◽  
...  
Keyword(s):  
Direct Injection ◽  
Gasoline Direct Injection ◽  
Si Engine ◽  
Lean Burn
Sign in / Sign up

Export Citation Format

Share Document