scholarly journals Concerning The Effect of Surface Material on Nucleate Boiling Heat Transfer of R-113

2011 ◽  
Vol 01 (02) ◽  
pp. 22-27 ◽  
Author(s):  
Reza Hosseini ◽  
Amir Gholaminejad ◽  
Mahdi Nabil
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Nucleate Boiling ◽  
Surface Material ◽  
Nucleate Boiling Heat Transfer ◽  
Effect Of Surface

Effect of surface configuration on nucleate boiling heat transfer

1984 ◽  
Vol 27 (9) ◽  
pp. 1559-1571 ◽  
Author(s):  
Nishikawa Kaneyasu ◽  
Fujita Yasunobu ◽  
Uchida Satoru ◽  
Ohta Haruhiko
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Nucleate Boiling ◽  
Surface Configuration ◽  
Nucleate Boiling Heat Transfer ◽  
Effect Of Surface

Concerning the Effect of Surface Material on Nucleate Boiling Heat Transfer of R-113

2011 ◽  
Author(s):  
R. Hosseini ◽  
A. Gholaminejad ◽  
Mahdi Nabil ◽  
Mohammad Hossein Samadinia
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Boiling Heat Transfer ◽  
Nucleate Boiling ◽  
High Heat ◽  
Heat Fluxes ◽  
Surface Material ◽  
Effect Of Surface

This paper presents results of an experimental investigation carried out to determine the effects of surface material on nucleate pool boiling heat transfer of refrigerant R113. Experiments were performed on horizontal circular plates of brass, copper and aluminum. The heat transfer coefficient was evaluated by measuring wall superheat and effective heat flux removed by boiling. The experiments were carried out in the heat flux range of 8 to 200kW/m2. The obtained results have shown significant effect of surface material, with copper providing the highest heat transfer coefficient among the samples, and aluminum the least. There was negligible difference at low heat fluxes, but copper showed 23% better performance at high heat fluxes than aluminum and 18% better than brass.

An Overview: Analysis of Heat and Mass Transfer in Fractal Media by Fractal Geometry and Technique

2010 ◽  
Author(s):  
Boming Yu
Keyword(s):  
Heat Transfer ◽  
Mass Transfer ◽  
Porous Media ◽  
Heat And Mass Transfer ◽  
Oil Recovery ◽  
Fractal Geometry ◽  
Boiling Heat Transfer ◽  
Nucleate Boiling ◽  
Fractal Media ◽  
Nucleate Boiling Heat Transfer

In the past three decades, fractal geometry and technique have received considerable attention due to its wide applications in sciences and technologies such as in physics, mathematics, geophysics, oil recovery, material science and engineering, flow and heat and mass transfer in porous media etc. The fractal geometry and technique may become particularly powerful when they are applied to deal with random and disordered media such as porous media, nanofluids, nucleate boiling heat transfer. In this paper, a summary of recent advances is presented in the areas of heat and mass transfer in fractal media by fractal geometry technique. The present overview includes a brief summary of the fractal geometry technique applied in the areas of heat and mass transfer; thermal conductivities of porous media and nanofluids; nucleate boiling heat transfer. A few comments are made with respect to the theoretical studies that should be made in the future.

Visualization of Boiling Heat Transfer on Micro Porous Coated Surface in Confined Space

2013 ◽  
Author(s):  
Chien-Yuh Yang ◽  
Chien-Fu Liu
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Boiling Heat Transfer ◽  
Heat Transfer Performance ◽  
Heating Surface ◽  
Nucleate Boiling ◽  
Confined Space ◽  
Two Phase ◽  
Nucleate Boiling Heat Transfer ◽  
Coated Surface

Numerous researches have been developed for pool boiling on microporous coated surface in the past decade. The nucleate boiling heat transfer was found to be increased by up to 4.5 times than that on uncoated surface. Recently, the two-phase micro heat exchangers have been considered for high flux electronic devices cooling. The enhancement techniques for improving the nucleate boiling heat transfer performance in the micro heat exchangers have gotten more importance. Previous studies of microporous coatings, however, have been restricted to boiling in unconfined space. No studies have been made on the feasibility of using microporous coatings for enhancing boiling in confined spaces. This study provides an experimental observation of the vapor generation and leaving processes on microporous coatings surface in a 1-mm confined space. It would be helpful for understanding the mechanism of boiling heat transfer and improving the design of two-phase micro heat exchangers. Aluminum particles of average diameter 20 μm were mixed with a binder and a carrier to develop a 150 μm thickness boiling enhancement paint on a 3.0 cm by 3.0 cm copper heating surface. The heating surface was covered by a thin glass plate with a 1 mm spacer to form a 1 mm vertical narrow space for the test section. The boiling phenomenon was recorded by a high speed camera. In addition to the three boiling regimes observed by Bonjour and Lallemand [1], i.e., isolated deformed bubbles, coalesced bubbles and partial dryout at low, moderate and high heat fluxes respectively in unconfined space, a suction and blowing process was observed at the highest heat flux condition. Owing to the space confinement, liquid was sucked and vapor was expelled periodically during the bubble generation process. This mechanism significantly enhanced the boiling heat transfer performance in confined space.

Sign in / Sign up

Export Citation Format

Share Document