scholarly journals Anti-Corrosion Test on Basal Slope Protection Materials

Detection ◽  
2016 ◽  
Vol 04 (01) ◽  
pp. 9-15
Author(s):  
Ronglan Zhang
Keyword(s):  
Corrosion Test

scholarly journals Effects of Alloying Elements on the Corrosion Behavior of Sputter–deposited Zr–(12–21)Cr–W Alloys in 0.5 M NaCl Solution

1970 ◽  
Vol 25 ◽  
pp. 75-82
Author(s):  
Basu Ram Aryal ◽  
Jagadeesh Bhattarai
Keyword(s):  
Corrosion Test ◽  
Open Circuit Potential ◽  
Chemical Society ◽  
Open Circuit ◽  
Sputter Deposition ◽  
Nacl Solution ◽  
Corrosion Rates ◽  
Sputter Deposited ◽  
Stable Passivity ◽  
Zirconium Metal

The synergistic effect of the simultaneous additions of tungsten and zirconium in thesputter-deposited amorphous or nanocrystalline Zr-(12-21)Cr-W alloys is studied in 0.5 MNaCl solution open to air at 25°C using corrosion tests and open circuit potentialmeasurements. Corrosion rates of the sputter-deposited Zr-(12-21)Cr-W alloys containing10-80 at % tungsten (that is, 0.95-1.85 x 10-2 mm.y-1) are more than one order of magnitudelower than that of the sputter-deposited tungsten and even lower than those of zirconium aswell as chromium in 0.5 M NaCl solution. The addition of 8-73 at % zirconium content inthe sputter-deposited binary W-(12-21)Cr alloys seems to be more effective to improve thecorrosion-resistant properties of the sputter-deposited ternary Zr-Cr-W alloys containing12-21 at % chromium in 0.5 M NaCl solution. The sputter-deposited Zr-(17-21)Cr-W alloyscontaining an adequate amounts of zirconium metal showed the more stable passivity andshowed higher corrosion resistance than those of alloy-constituting elements in 0.5 M NaClsolution open to air at 25°C.Keywords: Zr-(12-21)Cr-W alloys, sputter deposition, corrosion test, open circuit potential,0.5 M NaCl.DOI:  10.3126/jncs.v25i0.3305Journal of Nepal Chemical Society Volume 25, 2010 pp 75-82

scholarly journals Effect of Oxide Scale Microstructure on Atmospheric Corrosion Behavior of Hot Rolled Steel Strip

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 517
Author(s):  
Bin Sun ◽  
Lei Cheng ◽  
Chong-Yang Du ◽  
Jing-Ke Zhang ◽  
Yong-Quan He ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Oxide Scale ◽  
Corrosion Product ◽  
Corrosion Behavior ◽  
Corrosion Test ◽  
Atmospheric Corrosion ◽  
Corrosion Mechanism ◽  
Type I ◽  
Rust Layer ◽  
Hot Rolled

The atmospheric corrosion behavior of a hot-rolled strip with four types (I–IV) of oxide scale was investigated using the accelerated wet–dry cycle corrosion test. Corrosion resistance and porosity of oxide scale were studied by potentiometric polarization measurements. Characterization of samples after 80 cycles of the wet–dry corrosion test showed that scale comprised wüstite and magnetite had strongest corrosion resistance. Oxide scale composed of inner magnetite/iron (>70%) and an outer magnetite layer had the weakest corrosion resistance. The corrosion kinetics (weight gain) of each type of oxide scale followed an initial linear and then parabolic (at middle to late corrosion) relationship. This could be predicted by a simple kinetic model which showed good agreement with the experimental results. Analysis of the potentiometric polarization curves, obtained from oxide coated steel electrodes, revealed that the type I oxide scale had the highest porosity, and the corrosion mechanism resulted from the joint effects of electrochemical behavior and the porosity of the oxide scale. In the initial stage of corrosion, the corrosion product nucleated and an outer rust layer formed. As the thickness of outer rust layer increased, the corrosion product developed on the scale defects. An inner rust layer then formed in the localized pits as crack growth of the scale. This attacked the scale and expanded into the substrate during the later stage of corrosion. At this stage, the protective effect of the oxide scale was lost.

Effect of CO2 on Anti-Corrosion Property of a Polyurea Coating Modified with Organosilicone

2014 ◽  
Vol 789 ◽  
pp. 466-470
Author(s):  
Qing Hao Shi ◽  
Bing Ying Wang ◽  
Bin Zhao
Keyword(s):  
High Temperature ◽  
Partial Pressure ◽  
Composite Coating ◽  
Corrosion Test ◽  
Electrochemical Impedance ◽  
Failure Process ◽  
Corrosion Property ◽  
Corrosion Mechanism ◽  
Partial Pressures ◽  
High Temperature High Pressure

The corrosion mechanism of organic silicon modified polyurea composite coating under different CO2 partial pressures was studied using high-temperature autoclave, combined with scanning electron microscopy (SEM), adhesion tests and electrochemical impedance spectroscopy (EIS) technology. The experimental results showed that: there was no corrosion product formed on the surface of coating sample after high-temperature high-pressure corrosion test, and with the increasing of CO2 partial pressure, the coating adhesion and impedance values decline increases. Moreover CO2 partial pressure increases accelerated the failure process of polyurea composite coating system.

Bearing Corrosion Test for Lubricating Oils

1949 ◽  
Vol 21 (6) ◽  
pp. 737-743
Author(s):  
E. C. Hughes ◽  
J. D. Bartleson ◽  
M. L. Sunday
Keyword(s):  
Corrosion Test ◽  
Lubricating Oils
Sign in / Sign up

Export Citation Format

Share Document