scholarly journals Study of Thermally Induced Vibration of Non-Homogeneous Trapezoidal Plate with Parabolically Thickness Variation in Both Directions

2016 ◽  
Vol 07 (12) ◽  
pp. 1283-1296
Author(s):  
  Kavita ◽  
Satish Kumar ◽  
Pragati Sharma
Keyword(s):  
Thickness Variation ◽  
Thermally Induced ◽  
Trapezoidal Plate

Morphologies of Nonadherent Al2O3 and Matching Substrate Surfaces

1972 ◽  
Vol 30 ◽  
pp. 524-525
Author(s):  
C. S. Giggins ◽  
J. K. Tien ◽  
B. H. Kear ◽  
F. S. Pettit
Keyword(s):  
Electron Microscopy ◽  
Oxide Scale ◽  
Oxidation Resistance ◽  
Substrate Surface ◽  
Morphological Features ◽  
Thermally Induced ◽  
Oxide Spallation ◽  
Oxidation Resistant ◽  
Induced Stresses ◽  
Substrate Surfaces

The performance of most oxidation resistant alloys and coatings is markedly improved if the oxide scale strongly adheres to the substrate surface. Consequently, in order to develop alloys and coatings with improved oxidation resistance, it has become necessary to determine the conditions that lead to spallation of oxides from the surfaces of alloys. In what follows, the morphological features of nonadherent Al2O3, and the substrate surfaces from which the Al2O3 has spalled, are presented and related to oxide spallation.The Al2O3, scales were developed by oxidizing Fe-25Cr-4Al (w/o) and Ni-rich Ni3 (Al,Ta) alloys in air at 1200°C. These scales spalled from their substrates upon cooling as a result of thermally induced stresses. The scales and the alloy substrate surfaces were then examined by scanning and replication electron microscopy.The Al2O3, scales from the Fe-Cr-Al contained filamentary protrusions at the oxide-gas interface, Fig. 1(a). In addition, nodules of oxide have been developed such that cavities were formed between the oxide and the substrate, Fig. 1(a).

Some Quantification Problems in Parallel EELS Images

1990 ◽  
Vol 48 (2) ◽  
pp. 36-37
Author(s):  
G. Botton ◽  
G. L’Espérance ◽  
M.D. Ball ◽  
C.E. Gallerneault
Keyword(s):  
Electron Microscope ◽  
Imaging System ◽  
Signal To Noise Ratio ◽  
Scanning Transmission Electron Microscope ◽  
Acquisition Time ◽  
Thickness Variation ◽  
Transmission Electron ◽  
Distribution Of Elements ◽  
Scanning Transmission ◽  
Present Distribution

The recently developed parallel electron energy loss spectrometers (PEELS) have led to a significant reduction in spectrum acquisition time making EELS more useful in many applications in material science. Dwell times as short as 50 msec per spectrum with a PEELS coupled to a scanning transmission electron microscope (STEM), can make quantitative EEL images accessible. These images would present distribution of elements with the high spatial resolution inherent to EELS. The aim of this paper is to briefly investigate the effect of acquisition time per pixel on the signal to noise ratio (SNR), the effect of thickness variation and crystallography and finally the energy stability of spectra when acquired in the scanning mode during long periods of time.The configuration of the imaging system is the following: a Gatan PEELS is coupled to a CM30 (TEM/STEM) electron microscope, the control of the spectrometer and microscope is performed through a LINK AN10-85S MCA which is interfaced to a IBM RT 125 (running under AIX) via a DR11W line.

Applications of ultramicrotomy for materials characterization

1993 ◽  
Vol 51 ◽  
pp. 232-233
Author(s):  
R.T. Blackham ◽  
J.J. Haugh ◽  
C.W. Hughes ◽  
M.G. Burke
Keyword(s):  
Materials Science ◽  
Microstructural Analysis ◽  
Analytical Electron Microscopy ◽  
Austenitic Stainless Steels ◽  
Specimen Preparation ◽  
Preparation Technique ◽  
Thermally Induced ◽  
Radiation Induced ◽  
Characterization Of Materials

Essential to the characterization of materials using analytical electron microscopy (AEM) techniques is the specimen itself. Without suitable samples, detailed microstructural analysis is not possible. Ultramicrotomy, or diamond knife sectioning, is a well-known mechanical specimen preparation technique which has been gaining attention in the materials science area. Malis and co-workers and Glanvill have demonstrated the usefulness and applicability of this technique to the study of a wide variety of materials including Al alloys, composites, and semiconductors. Ultramicrotomed specimens have uniform thickness with relatively large electron-transparent areas which are suitable for AEM anaysis.Interface Analysis in Type 316 Austenitic Stainless Steel: STEM-EDS microanalysis of grain boundaries in austenitic stainless steels provides important information concerning the development of Cr-depleted zones which accompany M23C6 precipitation, and documentation of radiation induced segregation (RIS). Conventional methods of TEM sample preparation are suitable for the evaluation of thermally induced segregation, but neutron irradiated samples present a variety of problems in both the preparation and in the AEM analysis, in addition to the handling hazard.

Spin-crossover in an iron(iii) complex showing a broad thermal hysteresis

2021 ◽  
Author(s):  
Cyril Rajnák ◽  
Romana Mičová ◽  
Ján Moncoľ ◽  
Ľubor Dlháň ◽  
Christoph Krüger ◽  
...  
Keyword(s):  
Schiff Base ◽  
Schiff Base Ligand ◽  
Spin Crossover ◽  
Thermal Hysteresis ◽  
Mononuclear Complex ◽  
Hysteresis Width ◽  
Thermally Induced

A pentadentate Schiff-base ligand 3,5Cl-L2− and NCSe− form a iron(iii) mononuclear complex [Fe(3,5Cl-L)(NCSe)], which shows a thermally induced spin crossover with a broad hysteresis width of 24 K between 123 K (warming) and 99 K (cooling).

Thermally induced budding of phospholipid vesicles — a discontinuous process

1993 ◽  
Vol 3 (5) ◽  
pp. 631-645 ◽  
Author(s):  
J. Käs ◽  
E. Sackmann ◽  
R. Podgornik ◽  
S. Svetina ◽  
B. Žekš
Keyword(s):  
Phospholipid Vesicles ◽  
Thermally Induced ◽  
Discontinuous Process
Sign in / Sign up

Export Citation Format

Share Document