Dynamic Analysis of Structural Systems using Component Mode Synthesis

2009 ◽  
pp. 255-282 ◽  
Author(s):  
G. Muscolino
Keyword(s):  
Dynamic Analysis ◽  
Component Mode Synthesis ◽  
Structural Systems

Dynamic Analysis of Cage Stress in Tapered Roller Bearings Using Component-Mode-Synthesis Method

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Tomoya Sakaguchi ◽  
Kazuyoshi Harada
Keyword(s):  
Rigid Body ◽  
Dynamic Analysis ◽  
Boundary Point ◽  
Axial Load ◽  
Synthesis Method ◽  
Load Condition ◽  
Component Mode Synthesis ◽  
Analysis Model ◽  
Tapered Roller ◽  
Tapered Roller Bearings

In order to investigate cage stress in tapered roller bearings, a dynamic analysis tool considering both the six degrees of freedom of motion of the rollers and cage and the elastic deformation of the cage was developed. Cage elastic deformation is equipped using a component-mode-synthesis (CMS) method. Contact forces on the elastically deforming surfaces of the cage pocket are calculated at all node points of finite-elements on it. The location and pattern of the boundary points required for the component-mode-synthesis method were examined by comparing cage stresses in a static condition of pocket forces and constraints calculated by using the finite-element and the CMS methods. These results indicated that one boundary point lying at the center on each bar is appropriate for the effective dynamic analysis model focusing on the cage stress, especially at the pocket corners of the cages, which are actually broken. A behavior measurement of a polyamide cage in a tapered roller bearing was conducted for validating the analysis model. It was confirmed in both the experiment and analysis that the cage whirled under a large axial load condition and the cage center oscillated in a small amplitude under a small axial load condition. In the analysis, the authors discussed the four models including elastic bodies having a normal eigenmode of 0, 8 or 22, and rigid-body. There were small differences among the cage center loci of the four models. These two cages having normal eigenmodes of 0 and rigid-body whirled with imperceptible fluctuations. At least approximately 8 normal eigenmodes of cages should be introduced to conduct a more accurate dynamic analysis although the effect of the number of normal eigenmodes on the stresses at the pocket corners was insignificant. From the above, it was concluded to be appropriate to introduce one boundary point lying at the center on each pocket bar of cages and approximately 8 normal eigenmodes to effectively introduce the cage elastic deformations into a dynamic analysis model.

Selection of Degrees of Freedom for Dynamic Analysis

1987 ◽  
Vol 109 (1) ◽  
pp. 65-69 ◽  
Author(s):  
K. W. Matta
Keyword(s):  
Finite Element ◽  
Dynamic Analysis ◽  
Degrees Of Freedom ◽  
General Purpose ◽  
Component Mode Synthesis ◽  
Complex Structures ◽  
Large Complex ◽  
Static Condensation ◽  
Basis Vectors ◽  
Selection Of

A technique for the selection of dynamic degrees of freedom (DDOF) of large, complex structures for dynamic analysis is described and the formulation of Ritz basis vectors for static condensation and component mode synthesis is presented. Generally, the selection of DDOF is left to the judgment of engineers. For large, complex structures, however, a danger of poor or improper selection of DDOF exists. An improper selection may result in singularity of the eigenvalue problem, or in missing some of the lower frequencies. This technique can be used to select the DDOF to reduce the size of large eigenproblems and to select the DDOF to eliminate the singularities of the assembled eigenproblem of component mode synthesis. The execution of this technique is discussed in this paper. Examples are given for using this technique in conjunction with a general purpose finite element computer program GENSAM[1].

scholarly journals Dynamic Analysis of Crankshaft Using Component Mode Synthesis (Part 2)

1987 ◽  
Vol 22 (8) ◽  
pp. 521-528
Author(s):  
Koji Tanida ◽  
Minoru Kubota ◽  
Noboru Hasegawa ◽  
Eiichi Nakagawa
Keyword(s):  
Dynamic Analysis ◽  
Component Mode Synthesis

A component mode synthesis based hybrid method for the dynamic analysis of complex systems

2015 ◽  
Vol 357 ◽  
pp. 285-299 ◽  
Author(s):  
E. Roibás Millán ◽  
M. Chimeno Manguán ◽  
F. Simón Hidalgo
Keyword(s):  
Complex Systems ◽  
Dynamic Analysis ◽  
Hybrid Method ◽  
Component Mode Synthesis

The Application of Finite Element Methods to the Dynamic Analysis of Flexible Spatial and Co-Planar Linkage Systems

1981 ◽  
Vol 103 (3) ◽  
pp. 643-651 ◽  
Author(s):  
W. Sunada ◽  
S. Dubowsky
Keyword(s):  
Finite Element ◽  
Dynamic Analysis ◽  
High Speed ◽  
Robotic Manipulators ◽  
Component Mode Synthesis ◽  
System Of Equations ◽  
Flexible Links ◽  
Analysis Techniques ◽  
Spatial Mechanisms ◽  
Coordinate Reduction

An analytical method is presented for the dynamics of spatial mechanisms containing complex-shaped, flexible links with application to both high-speed industrial machines and robotic manipulators. Existing NASTRAN-type finite element structural analysis programs are combined with 4 × 4 matrix dynamic analysis techniques and Component Mode Synthesis coordinate reduction to yield a procedure capable of analyzing complex, non-linear spatial mechanisms with irregularly shaped links in great detail, yet producing a system of equations small enough for efficient numerical integration. The method is applied to two examples.

Sign in / Sign up

Export Citation Format

Share Document