Assessing the Effect of Two Entering Triangular Initial Geometric Imperfections on the Buckling Strength of an Axisymmetric Shell subjected to Uniform Axial Compression

2012 ◽  
Author(s):  
A. Khamlichi ◽  
A. Limam
Keyword(s):  
Axial Compression ◽  
Geometric Imperfections ◽  
Buckling Strength ◽  
Axisymmetric Shell ◽  
Initial Geometric Imperfections

On the Choice of Initial Geometric Imperfections in Externally Pressurized Shells

1999 ◽  
Vol 121 (1) ◽  
pp. 71-76 ◽  
Author(s):  
J. Błachut ◽  
O. R. Jaiswal
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Carrying Capacity ◽  
Circular Cross Section ◽  
Load Carrying Capacity ◽  
Geometric Imperfections ◽  
Elliptical Cross ◽  
Buckling Strength ◽  
Load Carrying ◽  
Initial Geometric Imperfections

Localized and global, of eigenmode type, initial geometric imperfections were superimposed on perfect torispherical, ellipsoidal, and toroidal shells of circular and elliptical cross section. Reduction of the load-carrying capacity was then calculated numerically for various geometries and the yield point of material which was assumed to be mild steel. Results show that the buckling strength of torispheres and ellipsoids could be strongly affected by imperfections, but reduction of its magnitude was dependent on the choice of imperfection shape and, more importantly, on the imperfection’s location. Calculations carried out for closed toroids of circular cross section show that these shells are not sensitive to eigenmode-type imperfections, while toroids with elliptical cross sections are sensitive to eigen-imperfections.

Numerical Study about Combined Effect of Distributed Initial Imperfections and Dent on Ultimate Strength of Square Plates under Uni-Axial Compression

2015 ◽  
Vol 813-814 ◽  
pp. 1037-1041 ◽  
Author(s):  
Duraikannou Peroumal ◽  
E. Sidhuvilaji ◽  
B. Prabu ◽  
A.V. Raviprakash
Keyword(s):  
Ultimate Strength ◽  
Axial Compression ◽  
Thick Plate ◽  
Numerical Study ◽  
Combined Effect ◽  
Geometric Imperfections ◽  
Buckling Strength ◽  
Initial Imperfections ◽  
Numerical Result ◽  
Local Dent

Aim of this present work is to study the combined effect of distributed geometric global imperfection and a local dent on buckling strength of thin square plates subjected to uni-axial compression. Steady state non linear FE analysis including both material and geometrical non linearities is used to determine the ultimate strength of the dented plates. From the numerical result it is found that in case of low thickness plates global geometric imperfections effect is more dominant and in case of thick plate dent effect is found to be more dominant.

Buckling strength of axially compressed thin axisymmetric shells as affected by localized initial geometric imperfections

2012 ◽  
Vol 3 (1) ◽  
pp. 1-14 ◽  
Author(s):  
J. El Bahaoui ◽  
L. El Bakkali ◽  
A. Khamlichi
Keyword(s):  
Finite Element Method ◽  
Thin Shells ◽  
The Finite Element Method ◽  
Triangular Form ◽  
Geometric Imperfections ◽  
Buckling Strength ◽  
Aspect Ratios ◽  
Small Influence ◽  
Initial Geometric Imperfections ◽  
Axisymmetric Shells

Abstract Buckling analysis of axially compressed cylindrical shells having one or two localized initial geometric imperfections was performed by using the finite element method. The imperfections of entering triangular form were assumed to be positioned symmetrically at the mid shell length. The buckling load was assessed in terms of shell aspect ratios, imperfection amplitude and wavelength, and the distance separating the imperfections. The obtained results have shown that amplitude and wavelength have major effects, particularly for short and thin shells. Two interacting imperfections were found to be more severe than a single imperfection, but the distance separating them has small influence.

Appraisal of Allowable Loads by Simplified Rules

1986 ◽  
Vol 108 (2) ◽  
pp. 131-137
Author(s):  
D. Moulin
Keyword(s):  
Experimental Investigation ◽  
Plastic Region ◽  
Thin Structures ◽  
Geometric Imperfections ◽  
Buckling Behavior ◽  
Simplified Method ◽  
Post Buckling ◽  
Initial Geometric Imperfections ◽  
Fast Breeder Reactors ◽  
Breeder Reactors

This paper presents a simplified method to analyze the buckling of thin structures like those of Liquid Metal Fast Breeder Reactors (LMFBR). The method is very similar to those used for the buckling of beams and columns with initial geometric imperfections, buckling in the plastic region. Special attention is paid to the strain hardening of material involved and to possible unstable post-buckling behavior. The analytical method uses elastic calculations and diagrams that account for various initial geometric defects. An application of the method is given. A comparison is made with an experimental investigation concerning a representative LMFBR component.

Evaluation of Compressive Strengths of HPS Plate Systems Stiffened with Trapezoidal Stiffeners

2013 ◽  
Vol 671-674 ◽  
pp. 1025-1028
Author(s):  
Dong Ku Shin ◽  
Kyungsik Kim
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Performance ◽  
Nonlinear Finite Element ◽  
Linear Strain ◽  
Element Analysis ◽  
Geometric Imperfections ◽  
Eurocode 3 ◽  
Initial Geometric Imperfections ◽  
Plate System

The ultimate compressive strengths of high performance steel (HPS) plate system stiffened longitudinally by closed stiffeners have been investigated by the nonlinear finite element analysis. Both conventional and high performance steels were considered in models following multi-linear strain hardening constitutive relationships. Initial geometric imperfections and residual stresses were also incorporated in the analysis. Numerical results have been compared to compressive strengths from Eurocode 3 EN 1993-1-5 and FHWA-TS-80-205. It has been found that although use of Eurocode 3 EN 1993-1-5 and FHWA-TS-80-205 may lead to highly conservative design strengths when very large column slenderness parameters are encountered

scholarly journals ANÁLISE NUMÉRICA DE PERFIS DE AÇO FORMADOS A FRIO EM SEÇÃO “I” CONSTITUÍDA POR DUPLO “U” SUBMETIDOS À COMPRESSÃO

2020 ◽  
Vol 12 (1) ◽  
pp. 95-110
Author(s):  
Gabriel Cintra Macedo ◽  
Wanderson Fernando Maia
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Plate Thickness ◽  
Experimental Studies ◽  
Structural Behavior ◽  
The Finite Element Method ◽  
Geometric Imperfections ◽  
Initial Geometric Imperfections ◽  
Normal Strength ◽  
Double Channel

Although the section “I”, in double channel, is widely used, there are few studies on its behavior. Therefore, this work aims to contribute to a greater mastery over the structural behavior of this built-up sections. A nonlinear numerical analysis was performed using the Finite Element Method in the Ansys program, using existing experimental studies as a comparative database. The effect of length, number of connections, plate thickness and the presence of geometric and material imperfections on the normal strength of the columns. For this analysis, it was essential to consider the initial geometric imperfections, because there was a considerable reduction in the normal strength of the columns, thus getting closer to the values obtained experimentally. With regard to normative procedures, values against security were found in most cases, showing the need to conduct further studies in the area for the development of more appropriate formulations.

Clamped torispherical shells under external pressure — some new results

1988 ◽  
Vol 23 (1) ◽  
pp. 9-24 ◽  
Author(s):  
J Blachut ◽  
G D Galletly
Keyword(s):  
Failure Mode ◽  
External Pressure ◽  
Spherical Cap ◽  
Geometric Imperfections ◽  
Collapse Pressure ◽  
Modes Of Failure ◽  
Shell Buckling ◽  
Bifurcation Buckling ◽  
Initial Geometric Imperfections ◽  
The One

Perfect clamped torispherical shells subjected to external pressure are analysed in the paper using the BOSOR 5 shell buckling program. Various values of the knuckle radius-to-diameter ratio ( r/D) and the spherical cap radius-to-thickness ratio ( Rs/ t) were studied, as well as four values of σyp, the yield point of the material. Buckling/collapse pressures, modes of failure and the development of plastic zones in the shell wall were determined. A simple diagram is presented which enables the failure mode in these shells to be predicted. The collapse pressures, pc, were also plotted against the parameter Λs (√( pyp/ pcr)). When the controlling failure mode was axisymmetric yielding in the knuckle, the collapse pressure curves depended on the value of σyp, which is unusual. However, when the controlling failure mode was bifurcation buckling (at the crown/knuckle junction), the collapse pressure curves for the various values of σyp all merged, i.e., they were independent of σyp. This latter situation is the one which normally occurs with the buckling of cylindrical and hemispherical shells. A limited investigation was also made into the effects of axisymmetric initial geometric imperfections on the strength of externally-pressurised torispherical shells. When the failure mode was axisymmetric yielding in the knuckle, initial imperfections of moderate size did not affect the collapse pressures. In the cases where bifurcation buckling at the crown/knuckle junction occurred, small initial geometric imperfections at the apex did not affect the buckling pressure, but axisymmetric imperfections at the buckle location did influence it. With the other failure mode (i.e., axisymmetric yielding collapse at the crown of the shell), initial geometric imperfections caused a reduction in the torisphere's strength.

Sign in / Sign up

Export Citation Format

Share Document