Physical properties of the mor layer in a Scots pine stand I. Hydraulic conductivity

1997 ◽  
Vol 77 (4) ◽  
pp. 627-634 ◽  
Author(s):  
A. Laurén ◽  
J. Heiskanen
Keyword(s):  
Hydraulic Conductivity ◽  
Pinus Sylvestris ◽  
Scots Pine ◽  
Hydraulic Properties ◽  
Matric Potential ◽  
Unsaturated Hydraulic Conductivity ◽  
Undisturbed Samples ◽  
Constant Head ◽  
Humified Peat ◽  
Properties Of Soil

Hydraulic conductivity in the mor layer of a Scots pine (Pinus sylvestris L.) stand was measured in undisturbed samples using the constant-head permeameter and instantaneous-profile method. Saturated hydraulic conductivity (Ks) averaged 2.9 × 102 m d−1. With a decrease in matric potential (ψ) from −4 kPa to −70 kPa the unsaturated hydraulic conductivity (K(ψ)) decreased from 3.1 × 10−3 to 1.1 × 10−8 m d−1. Ks and K(ψ) were similar to those reported in the literature for low-humified peat. The variation in hydraulic conductivity within a stand of Scots pine at a given matric potential was large, ranging from one to two orders of magnitude. Key words: F horizon, humus, hydraulic properties of soil

Measuring unsaturated hydraulic conductivity (K(ψm)) of the F and H soil organic layers at small matric potential (ψm)

2011 ◽  
Vol 91 (6) ◽  
pp. 965-968
Author(s):  
B. Wilske ◽  
E. A. Johnson
Keyword(s):  
Hydraulic Conductivity ◽  
Large Data ◽  
Cold Climate ◽  
Organic Layer ◽  
Matric Potential ◽  
Large Variability ◽  
Organic Layers ◽  
Soil Organic Layer ◽  
Unsaturated Hydraulic Conductivity ◽  
Constant Head

Wilske, B. and Johnson, E. A. 2011. Measuring unsaturated hydraulic conductivity (K(ψm)) of the F and H soil organic layers at small matric potential (ψm). Can. J. Soil Sci. 91: 965–968. K(ψm) of the soil organic layers is a key parameter to assess water redistribution in cold-climate forests. This study tested the twin suction disc apparatus (TSD) as a new method to measure K(ψm) of the F and H layers directly. We compared the results to two studies. One represents a large data base, the other used similar sample locations; but both derived K(ψm) from combining two methods, i.e., pressure plate measurements combined with the instantaneous profile technique or the constant head approach. The TSD data are consistent with previous results considering the large variability in K(ψm) from the combined methods. This suggests that the TSD method represents an alternative to determine K(ψm) of the soil organic layer.

Hyphal colonization of Rhizophagus irregularis increases unsaturated hydraulic conductivity of a loamy sand distant from roots

2021 ◽  
Author(s):  
Michael Bitterlich ◽  
Richard Pauwels
Keyword(s):  
Hydraulic Conductivity ◽  
Water Content ◽  
Hydraulic Properties ◽  
Volumetric Water Content ◽  
Rhizophagus Irregularis ◽  
Loamy Sand ◽  
Soil Hydraulic Properties ◽  
Unsaturated Hydraulic Conductivity ◽  
Soil Hydraulic ◽  
Root Exclusion

<p>Hydraulic properties of mycorrhizal soils have rarely been reported and difficulties in directly assigning potential effects to hyphae of arbuscular mycorrhizal fungi (AMF) arise from other consequences of AMF being present, i.e. their influence on growth and water consumption rates of their host plants that both also influence soil hydraulic properties.</p><p>We assumed that the typical nylon meshes used for root-exclusion experiments in mycorrhizal research can provide a dynamic hydraulic barrier. It is expected that the uniform pore size of the rigid meshes causes a sudden hydraulic decoupling of the enmeshed inner volume from the surrounding soil as soon as the mesh pores become air-filled. Growing plants below the soil moisture threshold for hydraulic decoupling would minimize plant-size effects on root-exclusion compartments and allow for a more direct assignment of hyphal presence to modulations in soil hydraulic properties.</p><p>We carried out water retention and hydraulic conductivity measurements with two tensiometers introduced in two different heights in a cylindrical compartment (250 cm³) containing a loamy sand, either with or without the introduction of a 20 µm nylon mesh equidistantly between the tensiometers. Introduction of a mesh reduced hydraulic conductivity across the soil volumes by two orders of magnitude from 471 to 6 µm d<sup>-1</sup> at 20% volumetric water content.</p><p>We grew maize plants inoculated or not with Rhizophagus irregularis in the same soil in pots that contained root-exclusion compartments while maintaining 20% volumetric water content. When hyphae were present in the compartments, water potential and unsaturated hydraulic conductivity increased for a given water content compared to compartments free of hyphae. These differences increased with progressive soil drying.</p><p>We conclude that water extractability from soils distant to roots can be facilitated under dry conditions when AMF hyphae are present.</p><p> </p>

scholarly journals Impact of Soil Amendments on the Hydraulic Conductivity of Boreal Agricultural Podzols

Agriculture ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 133 ◽  
Author(s):  
Dinushika Wanniarachchi ◽  
Mumtaz Cheema ◽  
Raymond Thomas ◽  
Vanessa Kavanagh ◽  
Lakshman Galagedara
Keyword(s):  
Hydraulic Conductivity ◽  
Vadose Zone ◽  
Hydraulic Properties ◽  
Soil Amendments ◽  
Dairy Manure ◽  
Soil Hydrology ◽  
Inorganic N ◽  
Infiltration Rates ◽  
Agricultural Setting ◽  
Properties Of Soil

Hydraulic properties of soil are the basis for understanding the flow and transport through the vadose zone. It has been demonstrated that different soil amendments can alter the soil properties affecting soil hydrology. The aim of this study was to determine the effect of soil amendments on hydraulic conductivity (K) of a loamy sand podzolic soil under both unsaturated (Kunsat) and near-saturated (near Ksat) conditions in an agricultural setting. A field experiment was conducted with two common soil amendments: Dairy manure (DM) in 2016 and 2017 and biochar (BC) once only in 2016. DM and BC were incorporated up to a depth of 0.15–0.20 m at a rate of 30,000 L ha−1 and 20 Mg ha−1, respectively. A randomized complete block experimental design was used and the plots planted with silage corn (Zea mays L.) without irrigation. The treatments were: Control without amendment (0N), inorganic N fertilizer (IN), two types of DM (IN+DM1 and IN+DM2), and two treatments with BC (IN+BC and IN+DM1+BC). Infiltration data were collected using a mini disk infiltrometer under three tension levels in which −0.04 and −0.02 m was ascribed as unsaturated (at the wet end) and −0.001 m as near-saturated condition. Based on the measured infiltration rates, Kunsat and near Ksat hydraulic conductivities were calculated. There were no significant effects of DM and BC on bulk density and near Ksat. Treatments IN+DM1, IN+DM2, and IN+DM1+BC significantly reduced the Kunsat compared to the control. Since these soil amendments can influence soil hydrology such as reduced infiltration and increased surface runoff, carefully monitored application of soil amendments is recommended.

Measurement of unsaturated hydraulic conductivity using tension and drip infiltrometers

Soil Research ◽  
2001 ◽  
Vol 39 (4) ◽  
pp. 823 ◽  
Author(s):  
N. J. McKenzie ◽  
H. P. Cresswell ◽  
H. Rath ◽  
D. Jacquier
Keyword(s):  
Hydraulic Conductivity ◽  
Soil Cores ◽  
Matric Potential ◽  
Constant Flux ◽  
Tension Infiltrometer ◽  
Unsaturated Hydraulic Conductivity ◽  
Wide Range ◽  
Constant Potential ◽  
Potential Methods ◽  
Large Decline

We investigated differences between constant flux and constant potential methods for determining unsaturated hydraulic conductivity in the laboratory. A cheap and robust method was required. The constant flux drip infiltrometer has been used with large intact cores on a wide range of Australian soils. However, the method can be simplified by replacing the drip infiltrometer with a constant potential tension infiltrometer (disc permeameter). We conducted a series of measurements using 9 soil cores to determine whether the measured hydraulic conductivity differed with each method at matric potentials of –10, –20, or –50 mm. Hysteresis effects were also examined because tension infiltrometer measurements are usually made on the adsorption curve of the hydraulic conductivity and matric potential [K(Ψ)] relationship. Drip infiltrometer measurements are often made on the desorption curve. The reproducibility of measurements on a single core was also examined. A large decline in K(Ψ ) was observed on some cores with repeated measurements and this effect was larger than differences between the methods. In the absence of evidence of slaking or dispersion, the suspected cause of the decline in K(Ψ) was clogging of pores from accumulation of microbial biomass and their by-products. The results support the view that K(Ψ) in some soils is a dynamic property. There were consistent differences between the constant flux and constant potential methods on those soil cores not exhibiting a large decline in K(Ψ) (the others were omitted from the method comparison). The tension infiltrometer method indicated greater hydraulic conductivity in soils with well-developed macrostructure when matric potential was greater than –50 mm. Hysteresis effects were significant with both methods and measurements made on desorption and adsorption curves are not considered comparable. Overall, we concluded that the tension infiltrometer method was more suited than the drip method for routine processing of large numbers of samples at low cost.

Soil structure, soil hydraulic properties and the soil water balance

Soil Research ◽  
1992 ◽  
Vol 30 (3) ◽  
pp. 265 ◽  
Author(s):  
HP Cresswell ◽  
DE Smiles ◽  
J Williams
Keyword(s):  
Hydraulic Conductivity ◽  
Water Balance ◽  
Soil Water ◽  
Soil Structure ◽  
Hydraulic Properties ◽  
Rainfall Regime ◽  
Soil Hydraulic Properties ◽  
Matric Potential ◽  
Moisture Characteristic

We review the influence of soil structural change on the fundamental soil hydraulic properties (unsaturated hydraulic conductivity and the soil moisture characteristic) and utilize deterministic modelling to assess subsequent effects on the soil water balance. Soil structure is reflected in the 0 to -100 kPa matric potential section of the soil moisture characteristic with marked changes often occurring in light to medium textured soils' (sands, sandy-loam, loams and clay-loams). The effect of long-term tillage on soil structure may decrease hydraulic conductivity within this matric potential range. The 'SWIM' (Soil Water Infiltration and Movement) simulation model was used to illustrate the effects of long-term conventional tillage and direct drilling systems on the water balance. The effects of plough pans, surface crusts and decreasing surface detention were also investigated. Significant structural deterioration, as evidenced by substantially reduced hydraulic conductivity, is necessary before significant runoff is generated in the low intensity rainfall regime of the Southern Tablelands (6 min rainfall intensity <45 mm h-1). A 10 mm thick plough pan (at a depth of 100 mm) in the A-horizon of a long-term conventionally tilled soil required a saturated hydraulic conductivity (K,) of less than 2.5 mm h-1 before runoff exceeded 10% of incident rainfall in this rainfall regime. Similarly, a crust K, of less than 2.5 mm h-1 was necessary before runoff exceeded 10% of incident rainfall (provided that surface detention was 2 or more). As the crust K, approached the rainfall rate, small decreases in Ks resulted in large increases in runoff. An increase in surface detention of 1 to 3 mm resulted in a large reduction in runoff where crust K, was less than 2-5 mm h-1. Deterministic simulation models incorporating well established physical laws are effective tools in the study of soil structural effects on the field water regime. Their application, however, is constrained by insufficient knowledge of the fundamental hydraulic properties of Australian soils and how they are changing in response to our land management.

HYDRAULIC PROPERTIES OF DISTURBED AND UNDISTURBED SOILS

1970 ◽  
Vol 50 (3) ◽  
pp. 431-437 ◽  
Author(s):  
C. F. SHAYKEWICH
Keyword(s):  
Hydraulic Conductivity ◽  
Hydraulic Properties ◽  
Water Retention ◽  
Available Water ◽  
Unsaturated Hydraulic Conductivity ◽  
Direct Measurements ◽  
Undisturbed Soils ◽  
Reliable Procedure ◽  
Sample Disturbance ◽  
High Suction

Studies showed that sample disturbance influenced water retention, lower limit of available water and unsaturated hydraulic conductivity. Significant differences in water retention due to sample disturbance occurred more frequently at low than at high suction. Results showed that sample disturbance may influence unsaturated hydraulic conductivity by changing area of water flow and/or tortuosity. A modified Millington and Quirk method did not adequately predict measured hydraulic conductivity, in either disturbed or undisturbed soils. In view of theoretical objections to extension of capillary theory to the dry end of the available water range, and the relative ease of direct measurements, it is suggested that direct measurement is the only reliable procedure available.

scholarly journals An experimental approach for determining unsaturated hydraulic properties of rock fractures

2004 ◽  
Vol 35 (3) ◽  
pp. 251-260 ◽  
Author(s):  
Hu Yunjin ◽  
Su Baoyu ◽  
Mao Genhai
Keyword(s):  
Hydraulic Conductivity ◽  
Capillary Pressure ◽  
Water Flow ◽  
Hydraulic Properties ◽  
Experimental Approach ◽  
Single Fracture ◽  
Rock Fractures ◽  
Unsaturated Hydraulic Conductivity ◽  
Connected Channels ◽  
Theoretical Saturation

An experimental approach for determining the unsaturated hydraulic properties (the relations between capillary pressure, saturation and unsaturated hydraulic conductivity) of rock fractures is developed and tested. Applying this approach to a single fracture, and with only water flowing, the capillary pressure–saturation and unsaturated hydraulic conductivity–capillary pressure relationships of the fracture during drainage and imbibition can be determined simultaneously. To facilitate the test of the validity of the experimental approach and to elucidate the characteristics of water flow in unsaturated fractures, an analogous fracture with parallel, connected channels of different apertures was fabricated. Experiments of unsaturated water flow in the analogous fracture were carried out. Some characteristics of water flow in unsaturated fractures (hysteresis between drainage and imbibition, etc.) were elucidated. Comparison of measured saturation values and theoretical saturation values corresponding to different apertures at the beginning of drainage and imbibition shows that the experimental approach presented in this paper is valid.

scholarly journals Effect of Chia Seed Mucilage on the Rhizosphere Hydraulic Characteristics

2021 ◽  
Vol 13 (6) ◽  
pp. 3303
Author(s):  
Faisal Hayat ◽  
Mohanned Abdalla ◽  
Muhammad Usman Munir
Keyword(s):  
Hydraulic Conductivity ◽  
Hydraulic Properties ◽  
Water Retention ◽  
Numerical Models ◽  
Chemical Properties ◽  
Water Retention Curve ◽  
Soil Drying ◽  
Retention Curve ◽  
Unsaturated Hydraulic Conductivity ◽  
Chia Seed

The rhizosphere is one of the major components in the soil–plant–atmosphere continuum which controls the flow of water from the soil into roots. Plant roots release mucilage in the rhizosphere which is capable of altering the physio-chemical properties of this region. Here, we showed how mucilage impacted on rhizosphere hydraulic properties, using simple experiments. An artificial rhizosphere, treated or not with mucilage, was placed in a soil sample and suction was applied to mimic the negative pressure in plant xylem. The measured water contents and matric potential were coupled with numerical models to estimate the water retention curve and hydraulic conductivity. A slower loss of water was observed in the treated scenario which resulted in an increase in water retention. Moreover, a slightly lower hydraulic conductivity was initially observed in the treated scenario (8.44 × 10−4 cm s−1) compared to the controlled one in saturated soil. Over soil drying, a relatively higher unsaturated hydraulic conductivity was observed. In summary, we demonstrated that mucilage altered the rhizosphere hydraulic properties and enhanced the unsaturated hydraulic conductivity. These findings improve our understanding of how plants capture more water, and postulate that mucilage secretion could be an optimal trait for plant survival during soil drying.

scholarly journals BIOSOCIAL DIVERSITY OF SCOTS PINE (PINUS SYLVESTRIS L.) IN A TREE STAND IN RELATION TO CHOSEN HYDRAULIC CONDUCTIVITY INDICATORS OF THE STEM

Wood Research ◽  
2021 ◽  
Vol 66 (3) ◽  
pp. 449-462
Author(s):  
Tomasz Jelonek ◽  
Witold Pazdrowski ◽  
Joanna Kopaczyk ◽  
Magdalena Arasimowicz-Jelonek ◽  
Arkadiusz Tomczak
Keyword(s):  
Hydraulic Conductivity ◽  
Pinus Sylvestris ◽  
Scots Pine ◽  
Lignin Content ◽  
Annual Rings ◽  
Tree Stand ◽  
Living Space ◽  
Peripheral Area ◽  
Pine Stands ◽  
Water Nutrients

The research focused in determining the lignification indicator of fresh needled springs and the mass of fresh needles in reference to the lignin content in tracheid walls of peripheral area of the stem (MFT/LC and MFN/LC) of Scots pine differentiated as far as its biosocial position within the community expressed by Kraft’s classification. The material for the analysis came from mature pine stands growing on North European Plain, on the territory of Poland. Chemical and structural analyses of wood encompassed the area of mature sapwood, i.e. thickness of the last 10 annual rings located at 1.3 m (DBH). It seems that the noticed differences values of both indicators (MFT/LC and MFN/LC) in pines belonging to the first three Kraft’s biological classes are connected with physiological, physical and structural conditionings of water transport with minerals in xylem and are closely connected with competition for sunlight, water, nutrients and living space.

Sign in / Sign up

Export Citation Format

Share Document