Thermoplastic Composite Riser Development for Ultradeep Water

2018 ◽  
Author(s):  
Alexander Smits ◽  
Teofilo Barbosa Neto ◽  
Henk de Boer
Keyword(s):  
Thermoplastic Composite ◽  
Ultradeep Water

Design of a unitized thermoplastic composite out-of-autoclave three-bay wingbox demonstrator

2021 ◽  
Author(s):  
Vincenzo Oliveri ◽  
Giovanni Zucco ◽  
Mohammad Rouhi ◽  
Enzo Cosentino ◽  
Trevor Young ◽  
...  
Keyword(s):  
Thermoplastic Composite ◽  
Out Of Autoclave

Comparative studies of nitrogen plasma and argon plasma treatment on the strength of PBO fibre reinforced high-temperature resistant thermoplastic composite

2021 ◽  
pp. 095400832098729
Author(s):  
K Sudheendra ◽  
Jennifer Vinodhini ◽  
M Govindaraju ◽  
Shantanu Bhowmik
Keyword(s):  
Contact Angle ◽  
High Temperature ◽  
Plasma Treatment ◽  
Sessile Drop ◽  
Dynamic Contact Angle ◽  
Argon Plasma ◽  
Film Surface ◽  
Fibre Surface ◽  
Nitrogen Plasma ◽  
Thermoplastic Composite

The study involves the processing of a novel poly [1, 4-phenylene-cis-benzobisoxazole] (PBO) fibre reinforced high-temperature thermoplastic composite with polyaryletherketone (PAEK) as the matrix. The PBO fibre and the PAEK film surface was modified using the method of argon and nitrogen plasma treatment. The investigation primarily focuses on evaluating the tensile properties of the fabricated laminates and correlating it with the effect of plasma treatment, surface characteristics, and its fracture surface. A 5% decrease in tensile strength was observed post argon plasma treatment while a 27% increase in strength was observed post nitrogen plasma treatment. The morphology of the failure surface was investigated by scanning electron microscopy and an interfacial failure was observed. Furthermore, the effect of plasma on the wettability of PBO fibres and PAEK film surface was confirmed by the Dynamic Contact Angle analysis and sessile drop method respectively. FTIR spectral analysis was done to investigate the effect of plasma treatment on the chemical structure on the surface. The results of the wettability study showed that the argon plasma treatment of the fibre surface increased its hydrophobicity while nitrogen plasma treatment resulted in the reduction of contact angle.

Localization simulation of forming-induced residual stresses of composite using prescribed boundary

2021 ◽  
pp. 073168442094118
Author(s):  
Qi Wu ◽  
Hongzhou Zhai ◽  
Nobuhiro Yoshikawa ◽  
Tomotaka Ogasawara ◽  
Naoki Morita
Keyword(s):  
Residual Stresses ◽  
Representative Volume Element ◽  
Computational Cost ◽  
Volume Element ◽  
Thermoplastic Composite ◽  
Structural Deformation ◽  
Element Analysis ◽  
Micro Scale ◽  
Representative Volume ◽  
Localization Approach

A novel localization approach that seamlessly bridges the macro- and micro-scale models is proposed and used to model the forming-induced residual stresses within a representative volume element of a fiber reinforced composite. The approach uses a prescribed boundary that is theoretically deduced by integrating the asymptotic expansion of a composite and the equal strain transfer, thus rendering the simulation setting to be easier than conventional approaches. When the localization approach is used for the finite element analysis, the temperature and residual stresses within an ideal cubic representative volume element are precisely simulated, given a sandwiched thermoplastic composite is formed under one-side cooling condition. The simulation results, after being validated, show that the temperature gradient has an impact on the local residual stresses, especially on the in-plane normal stress transverse to the fiber, and consequently, influences the structural deformation. This newly designed localization approach demonstrates the advantages of enhanced precision and reduced computational cost owing to the fast modeling of the finely meshed representative volume element. This is beneficial for a detailed understanding of the actual residual stresses at the micro-scale.

scholarly journals Fused Deposition Modelling of Fibre Reinforced Polymer Composites: A Parametric Review

2021 ◽  
Vol 5 (1) ◽  
pp. 29
Author(s):  
Narongkorn Krajangsawasdi ◽  
Lourens G. Blok ◽  
Ian Hamerton ◽  
Marco L. Longana ◽  
Benjamin K. S. Woods ◽  
...  
Keyword(s):  
Process Parameters ◽  
Mechanical Performance ◽  
Fibre Length ◽  
Processing Parameters ◽  
Thermoplastic Composite ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Fibre Reinforced Polymer ◽  
Printing Parameters

Fused deposition modelling (FDM) is a widely used additive layer manufacturing process that deposits thermoplastic material layer-by-layer to produce complex geometries within a short time. Increasingly, fibres are being used to reinforce thermoplastic filaments to improve mechanical performance. This paper reviews the available literature on fibre reinforced FDM to investigate how the mechanical, physical, and thermal properties of 3D-printed fibre reinforced thermoplastic composite materials are affected by printing parameters (e.g., printing speed, temperature, building principle, etc.) and constitutive materials properties, i.e., polymeric matrices, reinforcements, and additional materials. In particular, the reinforcement fibres are categorized in this review considering the different available types (e.g., carbon, glass, aramid, and natural), and obtainable architectures divided accordingly to the fibre length (nano, short, and continuous). The review attempts to distil the optimum processing parameters that could be deduced from across different studies by presenting graphically the relationship between process parameters and properties. This publication benefits the material developer who is investigating the process parameters to optimize the printing parameters of novel materials or looking for a good constituent combination to produce composite FDM filaments, thus helping to reduce material wastage and experimental time.

Sign in / Sign up

Export Citation Format

Share Document