A Comparative Study of Machining Parameters on Die-Sinking Electrical Discharge Machining (EDM) using Copper and Aluminium Electrodes on Hard Steels

2016 ◽  
Vol 3 (1) ◽  
pp. 22-44 ◽  
Author(s):  
Ashwani Kharola
Keyword(s):  
Surface Roughness ◽  
Discharge Current ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Die Steel ◽  
The Relationship

This paper considers effect of variation in value of Discharge current on different process parameters of Die Sinking EDM. The parameters considered were Material removal rate (MRR), Tool removal rate (TRR), Surface roughness (Ra) and Time (for machining required depth of cut). A total of 32 experiments were conducted on four different hard steels i.e. Die steel D3, En-8, En-19 and Stainless steel (SS-AISI-440C). The Copper and Aluminium electrodes brazed with mild steel were used for machining. The four different values of current i.e. 6A, 9A, 12A and 15A were considered for the study. The experimental results shows the relationship between MRR, TRR, Ra and Time with variation in magnitude of discharge current. This study also illustrates the relationship among different process parameter considered in the study. The results are shown with the help of graphs and tables.

scholarly journals Multi-Response Optimization of Electrical Discharge Machining Using the Desirability Function

Micromachines ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 72 ◽  
Author(s):  
Rafał Świercz ◽  
Dorota Oniszczuk-Świercz ◽  
Tomasz Chmielewski
Keyword(s):  
Surface Roughness ◽  
Discharge Current ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Desirability Function ◽  
Statistical Significance ◽  
Time Interval ◽  
Machining Parameters ◽  
Response Optimization

Electrical discharge machining (EDM) is a modern technology that is widely used in the production of difficult to cut conductive materials. The basic problem of EDM is the stochastic nature of electrical discharges. The optimal selection of machining parameters to achieve micron surface roughness and the recast layer with the maximal possible value of the material removal rate (MRR) is quite challenging. In this paper, we performed an analytical and experimental investigation of the influence of the EDM parameters: Surface integrity and MRR. Response surface methodology (RSM) was used to build empirical models on the influence of the discharge current I, pulse time ton, and the time interval toff, on the surface roughness (Sa), the thickness of the white layer (WL), and the MRR, during the machining of tool steel 55NiCrMoV7. The surface and subsurface integrity were evaluated using an optical microscope and a scanning profilometer. Analysis of variance (ANOVA) was used to establish the statistical significance parameters. The calculated contribution indicated that the discharge current had the most influence (over the 50%) on the Sa, WL, and MRR, followed by the discharge time. The multi-response optimization was carried out using the desirability function for the three cases of EDM: Finishing, semi-finishing, and roughing. The confirmation test showed that maximal errors between the predicted and the obtained values did not exceed 6%.

scholarly journals Investigation on Material Removal Rate and Surface Finish in Electrical Discharge Machining of AA 6061-B4C Composite Material

2021 ◽  
Vol 23 (12) ◽  
pp. 224-235
Author(s):  
N. Ethiraj ◽  
◽  
T. Sivabalan ◽  
Saibal Chatterjee ◽  
Seeramsetti Mahesh ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Composite Material ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Discharge Current ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Pulse On Time

One of the non-conventional techniques of metal removal manufacturing processes is electrical discharge machining (EDM). The objective of this paper is to prepare a composite material consisting of a matrix of Aluminium AA 6061 alloy and Boron carbide (B4C) as reinforcement and investigate the output responses, the material removal rate, the quality of the surface formed and overcut during EDM process. The process parameters discharge current, Pulse on time and Duty cycle along with the weight % of B4C are considered for investigation to investigate the output responses such as material removal rate, surface roughness and overcut. From the experimental results, it is observed that the weight % of reinforcement has more influence on the material removal rate. The parameters discharge current and pulse-on-time plays an important role in reducing the surface roughness and overcut. Microstructural study helps in understanding the effect of process parameters on the output responses.

Parametric Optimization of Wire Cut Electrical Discharge Machining on Al-9% PAC Composites using Desirability Approach

2018 ◽  
Vol 10 (6) ◽  
Author(s):  
G. Ramanan ◽  
R. Elangovan
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Discharge Current ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

In aerospace and automobile industries manufacturing complex structures using un-conventional machining is increased due to their precision and accuracy. This research investigates the influence of input parameters such as discharge current, pulse on time, pulse off time and servo speed rate of wire cut electrical discharge machining (WEDM) on material removal rate and surface roughness using Box Behnken design supported with response surface methodology. Aluminium alloy 7075 reinforced with 9 % wt. of activated carbon composite is used to carry out the machining process. Most influencing parameters are subjected as the conductive and non-conductive parameters in WEDM process. To find out the significant influence of each factor, analysis of variance was performed. The mathematical model is established using desirability technique and then the optimal machining parameters are determined. The best achieved WEDM performances - material removal rate and surface roughness are 10.46 mm3/min and 3.32μm respectively, by using optimum machining conditions - discharge current 2000mA, pulse on time 8.9µs, pulse off time 25µs and servo speed rate 150rpm at 0.8597 desirability value.

scholarly journals The Effect of Discharge Current and Pulse-On Time on Biocompatible Zr-based BMG Sinking-EDM

2020 ◽  
Vol 10 (1) ◽  
pp. 401-407
Author(s):  
Yanuar Rohmat Aji Pradana ◽  
Aldi Ferara ◽  
Aminnudin Aminnudin ◽  
Wahono Wahono ◽  
Jason Shian-Ching Jang
Keyword(s):  
Surface Roughness ◽  
Metallic Glasses ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Hardness ◽  
Recast Layer ◽  
Surface Evaporation ◽  
Pulse On Time

AbstractThe machinability information of Zr-based bulk metallic glasses (BMGs) are recently limited but essential to provide technological recommendation for the fabrication of the medical devices due to the material’s metastable nature. This study aims to investigate the material removal rate (MRR) and surface roughness under different current and pulse-on time of newly developed Ni- and Cu-free Zr-based BMG using sinking-electrical discharge machining (EDM). By using weightloss calculation, surface roughness test and scanning electron microscopy (SEM) observation on the workpiece after machining, both MRR and surface roughness were obtained to be increased up to 0.594 mm3/min and 5.50 μm, respectively, when the higher current was applied. On the other hand, the longer pulse-on time shifted the Ra into the higher value but lower the MRR value to only 0.183 mm3/min at 150 μs. Contrary, the surface hardness value was enhanced by both higher current and pulse-on time applied during machining indicating different level of structural change after high-temperature spark exposure on the BMG surface. These phenomena are strongly related to the surface evaporation which characterize the formation of crater and recast layer in various thicknesses and morphologies as well as the crystallization under the different discharge energy and exposure time.

Machining Feasibility of a New Developed Medium in Electrical Discharge Machining

2015 ◽  
Vol 656-657 ◽  
pp. 335-340 ◽  
Author(s):  
Fang Pin Chuang ◽  
Yan Cherng Lin ◽  
Hsin Min Lee ◽  
Han Ming Chow ◽  
A. Cheng Wang
Keyword(s):  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Environmentally Friendly ◽  
Industrial Applications ◽  
Deionized Water ◽  
Machining Parameters ◽  
Machining Performance ◽  
Machining Characteristics

The environment issue and green machining technique have been induced intensive attention in recent years. It is urgently need to develop a new kind dielectric to meet the requirements for industrial applications. The aim of this study is to develop a novel dielectric using gas media immersed in deionized water for electrical discharge machining (EDM). The developed machining medium for EDM can fulfill the environmentally friendly issue and satisfy the demand of high machining performance. The experiments were conducted by this developed medium to investigate the effects of machining parameters on machining characteristics in terms of material removal rate (MRR) and surface roughness. The developed EDM medium revealed the potential to obtain a stabilizing progress with excellent machining performance and environmentally friendly feature.

scholarly journals Investigation an assisting electrode powder mixed electrical discharge machining of nonconductive ceramic

2021 ◽  
Author(s):  
Dragan Rodic ◽  
Marin Gostimirovic ◽  
Milenko Sekulic ◽  
Borislav Savkovic ◽  
Branko Strbac
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Positive Effects ◽  
Assisting Electrode

Abstract It is well known that electrical discharge machining can be used in the processing of nonconductive materials. In order to improve the efficiency of machining modern engineering materials, existing electrical discharge machines are constantly being researched and improved or developed. The current machining of non-conductive materials is limited due to the relatively low material removal rate and high surface roughness. A possible technological improvement of electrical discharge machining can be achieved by innovations of existing processes. In this paper, a new approach for machining zirconium oxide is presented. It combines electrical discharge machining with assisting electrode and powder-mixed dielectric. The assisting electrode is used to enable electrical discharge machining of nonconductive material, while the powder-mixed dielectric is used to increase the material removal rate, reduce surface roughness, and decrease relative tool wear. The response surface method was used to generate classical mathematical models, analyzing the output performances of surface roughness, material removal rate and relative tool wear. Verification of the obtained models was performed based on a set of new experimental data. By combining these latest techniques, positive effects on machining performances are obtained. It was found that the surface roughness was reduced by 18%, the metal removal rate was increased by about 12% and the relative tool wear was reduced by up to 6% compared to electrical discharge machining with supported electrode without powder.

scholarly journals Analysis, predictive modelling and multi-response optimization in electrical discharge machining of Al-22%SiC metal matrix composite for minimization of surface roughness and hole overcut

2020 ◽  
Vol 7 ◽  
pp. 20 ◽  
Author(s):  
Subhashree Naik ◽  
Sudhansu Ranjan Das ◽  
Debabrata Dhupal
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Discharge Current ◽  
Metal Matrix ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machining Parameters ◽  
Response Optimization ◽  
Pulse On Time

Due to the widespread engineering applications of metal matrix composites especially in automotive, aerospace, military, and electricity industries; the achievement of desired shape and contour of the machined end product with intricate geometry and dimensions that are very challenging task. This experimental investigation deals with electrical discharge machining of newly engineered metal matrix composite of aluminum reinforced with 22 wt.% of silicon carbide particles (Al-22%SiC MMC) using a brass electrode to analyze the machined part quality concerning surface roughness and overcut. Forty-six sets of experimental trials are conducted by considering five machining parameters (discharge current, gap voltage, pulse-on-time, pulse-off-time and flushing pressure) based on Box-Behnken's design of experiments (BBDOEs). This article demonstrates the methodology for predictive modeling and multi-response optimization of machining accuracy and surface quality to enhance the hole quality in Al-SiC based MMC, employing response surface methodology (RSM) and desirability function approach (DFA). Finally, a novel approach has been proposed for economic analysis which estimated the total machining cost per part of rupees 211.08 during EDM of Al-SiC MMC under optimum machining conditions. Thereafter, under the influence of discharge current several observations are performed on machined surface morphology and hole characteristics by scanning electron microscope to establish the process. The result shows that discharge current has the significant contribution (38.16% for Ra, 37.12% in case of OC) in degradation of surface finish as well as the dimensional deviation of hole diameter, especially overcut. The machining data generated for the Al-SiC MMC will be useful for the industry.

Sign in / Sign up

Export Citation Format

Share Document