scholarly journals Intrapulpal temperature changes during curing of different bulk-fill restorative materials

2017 ◽  
Vol 36 (5) ◽  
pp. 566-572 ◽  
Author(s):  
Elif YASA ◽  
Cigdem ATALAYIN ◽  
Gamze KARACOLAK ◽  
Tugrul SARI ◽  
L. Sebnem TURKUN
Keyword(s):  
Temperature Changes ◽  
Restorative Materials

scholarly journals Temperature changes under demineralized dentin during polymerization of three resin-based restorative materials using QTH and LED units

2014 ◽  
Vol 39 (3) ◽  
pp. 155
Author(s):  
Sayed-Mostafa Mousavinasab ◽  
Maryam Khoroushi ◽  
Mohammadreza Moharreri ◽  
Mohammad Atai
Keyword(s):  
Temperature Changes ◽  
Restorative Materials ◽  
Demineralized Dentin

Cryo-TEM of amphiphilic polymer and amphiphile/polymer solutions

1993 ◽  
Vol 51 ◽  
pp. 876-877
Author(s):  
Yeshayahu Talmon
Keyword(s):  
Microstructural Characterization ◽  
Building Blocks ◽  
Quantitative Information ◽  
Physical Models ◽  
Specimen Preparation ◽  
Time Resolved ◽  
Temperature Changes ◽  
Temperature And Humidity ◽  
Microstructured Fluids ◽  
Air Streams

To achieve complete microstructural characterization of self-aggregating systems, one needs direct images in addition to quantitative information from non-imaging, e.g., scattering or Theological measurements, techniques. Cryo-TEM enables us to image fluid microstructures at better than one nanometer resolution, with minimal specimen preparation artifacts. Direct images are used to determine the “building blocks” of the fluid microstructure; these are used to build reliable physical models with which quantitative information from techniques such as small-angle x-ray or neutron scattering can be analyzed.To prepare vitrified specimens of microstructured fluids, we have developed the Controlled Environment Vitrification System (CEVS), that enables us to prepare samples under controlled temperature and humidity conditions, thus minimizing microstructural rearrangement due to volatile evaporation or temperature changes. The CEVS may be used to trigger on-the-grid processes to induce formation of new phases, or to study intermediate, transient structures during change of phase (“time-resolved cryo-TEM”). Recently we have developed a new CEVS, where temperature and humidity are controlled by continuous flow of a mixture of humidified and dry air streams.

Application of pyrometer and standard sample to determine surface temperature of studied materials

2019 ◽  
pp. 9-13
Author(s):  
V.Ya. Mendeleyev ◽  
V.A. Petrov ◽  
A.V. Yashin ◽  
A.I. Vangonen ◽  
O.K. Taganov
Keyword(s):  
Composite Material ◽  
Surface Temperature ◽  
Relative Error ◽  
Wavelength Range ◽  
Standard Sample ◽  
A Priori ◽  
Temperature Changes ◽  
Surface Temperatures ◽  
Relative Errors ◽  
Normal Emissivity

Determining the surface temperature of materials with unknown emissivity is studied. A method for determining the surface temperature using a standard sample of average spectral normal emissivity in the wavelength range of 1,65–1,80 μm and an industrially produced Metis M322 pyrometer operating in the same wavelength range. The surface temperature of studied samples of the composite material and platinum was determined experimentally from the temperature of a standard sample located on the studied surfaces. The relative error in determining the surface temperature of the studied materials, introduced by the proposed method, was calculated taking into account the temperatures of the platinum and the composite material, determined from the temperature of the standard sample located on the studied surfaces, and from the temperature of the studied surfaces in the absence of the standard sample. The relative errors thus obtained did not exceed 1,7 % for the composite material and 0,5% for the platinum at surface temperatures of about 973 K. It was also found that: the inaccuracy of a priori data on the emissivity of the standard sample in the range (–0,01; 0,01) relative to the average emissivity increases the relative error in determining the temperature of the composite material by 0,68 %, and the installation of a standard sample on the studied materials leads to temperature changes on the periphery of the surface not exceeding 0,47 % for composite material and 0,05 % for platinum.

Measuring Facial Skin Temperature Changes Caused by Mental Work-Load with Infrared Thermography

2016 ◽  
Vol 136 (11) ◽  
pp. 1581-1585 ◽  
Author(s):  
Tota Mizuno ◽  
Takeru Sakai ◽  
Shunsuke Kawazura ◽  
Hirotoshi Asano ◽  
Kota Akehi ◽  
...  
Keyword(s):  
Skin Temperature ◽  
Infrared Thermography ◽  
Work Load ◽  
Facial Skin ◽  
Mental Work ◽  
Temperature Changes ◽  
Mental Work Load
Sign in / Sign up

Export Citation Format

Share Document