scholarly journals Handbook of Mechanical Wear

1961 ◽  
Keyword(s):  
Mechanical Wear

Mechanical, wear, corrosion and biological properties of arc deposited titanium nitride coatings

2018 ◽  
Vol 344 ◽  
pp. 214-222 ◽  
Author(s):  
Susmit Datta ◽  
Mitun Das ◽  
Vamsi Krishna Balla ◽  
Subhadip Bodhak ◽  
V.K. Murugesan
Keyword(s):  
Titanium Nitride ◽  
Biological Properties ◽  
Mechanical Wear ◽  
Nitride Coatings

scholarly journals Modelling and Simulation of Mechanical Wear of Carburized Cutting Tool

2019 ◽  
Vol 35 ◽  
pp. 1067-1072
Author(s):  
Sunday A. Afolalu ◽  
Samson O. Ongbali ◽  
Abiodun A. Abioye ◽  
Segun Oladipupo ◽  
Oluseyi O. Ajayi ◽  
...  
Keyword(s):  
Cutting Tool ◽  
Modelling And Simulation ◽  
Mechanical Wear

Mechanical, wear, and dielectric behavior of TiO2 reinforced high-density polyethylene composites

2019 ◽  
Vol 136 (23) ◽  
pp. 47610 ◽  
Author(s):  
Akhil Ponnuruthiyil Shaji ◽  
Mahammad Ali Shaik ◽  
Brahma Raju Golla
Keyword(s):  
High Density Polyethylene ◽  
Dielectric Behavior ◽  
High Density ◽  
Mechanical Wear ◽  
Polyethylene Composites

scholarly journals Microstructure and Properties of Heat Affected Zone in High-Carbon Steel after Welding with Fast Cooling in Water

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5059
Author(s):  
Michail Nikolaevich Brykov ◽  
Ivan Petryshynets ◽  
Miroslav Džupon ◽  
Yuriy Anatolievich Kalinin ◽  
Vasily Georgievich Efremenko ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Heat Affected Zone ◽  
Welded Joints ◽  
High Carbon Steel ◽  
Low Carbon Steel ◽  
Tensile Tests ◽  
Low Carbon ◽  
High Carbon ◽  
Mechanical Wear ◽  
Fast Cooling

The purpose of the research was to obtain an arc welded joint of a preliminary quenched high-carbon wear resistant steel without losing the structure that is previously obtained by heat treatment. 120Mn3Si2 steel was chosen for experiments due to its good resistance to mechanical wear. The fast cooling of welding joints in water was carried out right after welding. The major conclusion is that the soft austenitic layer appears in the vicinity of the fusion line as a result of the fast cooling of the welding joint. The microstructure of the heat affected zone of quenched 120Mn3Si2 steel after welding with rapid cooling in water consists of several subzones. The first one is a purely austenitic subzone, followed by austenite + martensite microstructure, and finally, an almost fully martensitic subzone. The rest of the heat affected zone is tempered material that is heated during welding below A1 critical temperature. ISO 4136 tensile tests were carried out for the welded joints of 120Mn3Si2 steel and 09Mn2Si low carbon steel (ASTM A516, DIN13Mn6 equivalent) after welding with fast cooling in water. The tests showed that welded joints are stronger than the quenched 120Mn3Si2 steel itself. The results of work can be used in industries where the severe mechanical wear of machine parts is a challenge.

Mechanical wear models for metallic surfaces in sliding contact

1992 ◽  
Vol 25 (1A) ◽  
pp. A266-A272 ◽  
Author(s):  
B S Hockenhull ◽  
E M Kopalinsky ◽  
P L B Oxley
Keyword(s):  
Sliding Contact ◽  
Metallic Surfaces ◽  
Mechanical Wear
Sign in / Sign up

Export Citation Format

Share Document