scholarly journals FAÇADE DESIGN EFFECT ON CROSS-VENTILATION IN TAIWANESE SCHOOL BUILDINGS

2013 ◽  
Vol 8 (2) ◽  
pp. 90-111 ◽  
Author(s):  
W.H. Chiang ◽  
H.H. Hsu ◽  
J.S. Huang
Keyword(s):  
Numerical Scheme ◽  
Wind Profile ◽  
Incident Angle ◽  
Three Dimensional ◽  
Windward Side ◽  
School Buildings ◽  
Breathing Zone ◽  
Air Exchange Rate ◽  
Computational Fluid Dynamics Cfd ◽  
Shading Devices

This study performed a three-dimensional numerical prediction for the induced airflow patterns and mean age of air (MAGE) around and inside a naturally ventilated school building, while accounting for the wind profile effect. Various fenestrations, hallways, and shading devices on the windward side of building were analyzed to determine how they affected wind velocity, the incident angle of airflow, and MAGE distribution inside classrooms. The numerical scheme is based on a commercial computational fluid dynamics (CFD) code, PHOENICS. The incline of incoming wind was observed on higher floors that decreased the air exchange rate in the simulated room. The inclined airflow could be effectively deflected downward through the breathing zone by hallways, 1.2-m shades as overhangs, and 0.6-m louvers. Based on this research, an appropriate combination of external attachments on the windward side of building façade can be utilized to enhance ventilation in school buildings. (See Appendix 1 for nomenclature.)

Propagation and Reflection of Plane Waves in a Rotating Magneto-Elastic Fibre-Reinforced Semi Space with Surface Stress

2020 ◽  
Vol 22 (4) ◽  
pp. 939-958
Author(s):  
Indrajit Roy ◽  
D. P. Acharya ◽  
Sourav Acharya
Keyword(s):  
Surface Stress ◽  
Incident Angle ◽  
Plane Waves ◽  
Three Dimensional ◽  
Elastic Fibre ◽  
Amplitude Ratios ◽  
Governing Equations ◽  
Rotation Surface ◽  
Wave Velocities ◽  
Magnetic Field Rotation

AbstractThe present paper investigates the propagation of quasi longitudinal (qLD) and quasi transverse (qTD) waves in a magneto elastic fibre-reinforced rotating semi-infinite medium. Reflections of waves from the flat boundary with surface stress have been studied in details. The governing equations have been used to obtain the polynomial characteristic equation from which qLD and qTD wave velocities are found. It is observed that both the wave velocities depend upon the incident angle. After imposing the appropriate boundary conditions including surface stress the resultant amplitude ratios for the total displacements have been obtained. Numerically simulated results have been depicted graphically by displaying two and three dimensional graphs to highlight the influence of magnetic field, rotation, surface stress and fibre-reinforcing nature of the material medium on the propagation and reflection of plane waves.

Assessment of Unsteady Flows in Turbines

1992 ◽  
Vol 114 (1) ◽  
pp. 79-90 ◽  
Author(s):  
O. P. Sharma ◽  
G. F. Pickett ◽  
R. H. Ni
Keyword(s):  
Unsteady Flow ◽  
Three Dimensional ◽  
Flow Simulation ◽  
Experimental Investigations ◽  
Flow Parameters ◽  
Research Activities ◽  
Flow Features ◽  
Computational Fluid Dynamics Cfd ◽  
Turbine Design ◽  
The Impact

The impacts of unsteady flow research activities on flow simulation methods used in the turbine design process are assessed. Results from experimental investigations that identify the impact of periodic unsteadiness on the time-averaged flows in turbines and results from numerical simulations obtained by using three-dimensional unsteady Computational Fluid Dynamics (CFD) codes indicate that some of the unsteady flow features can be fairly accurately predicted. Flow parameters that can be modeled with existing steady CFD codes are distinguished from those that require unsteady codes.

The Effect of Bench Arrangements on the Natural Ventilation of a Multispan Greenhouse

2013 ◽  
Author(s):  
Sunita Kruger ◽  
Leon Pretorius
Keyword(s):  
Fluid Dynamics ◽  
Natural Ventilation ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Low Velocity ◽  
Lower Velocity ◽  
Cfd Models ◽  
Temperature Distributions ◽  
Computational Fluid Dynamics Cfd ◽  
Plant Level

In this paper, the influence of various bench arrangements on the microclimate inside a two-span greenhouse is numerically investigated using three-dimensional Computational Fluid Dynamics (CFD) models. Longitudinal and peninsular arrangements are investigated for both leeward and windward opened roof ventilators. The velocity and temperature distributions at plant level (1m) were of particular interest. The research in this paper is an extension of two-dimensional work conducted previously [1]. Results indicate that bench layouts inside the greenhouse have a significant effect on the microclimate at plant level. It was found that vent opening direction (leeward or windward) influences the velocity and temperature distributions at plant level noticeably. Results also indicated that in general, the leeward facing greenhouses containing either type of bench arrangement exhibit a lower velocity distribution at plant level compared to windward facing greenhouses. The latter type of greenhouses has regions with relatively high velocities at plant level which could cause some concern. The scalar plots indicate that more stagnant areas of low velocity appear for the leeward facing greenhouses. The windward facing greenhouses also display more heterogeneity at plant level as far as temperature is concerned.

scholarly journals Computational Analysis to Factor Wind into the Design of an Architectural Environment

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Hassam Nasarullah Chaudhry ◽  
John Kaiser Calautit ◽  
Ben Richard Hughes
Keyword(s):  
Fluid Dynamics ◽  
Power Generation ◽  
Computational Fluid Dynamics ◽  
Three Dimensional ◽  
Numerical Data ◽  
Navier Stokes ◽  
Windward Side ◽  
Average Value ◽  
Continuity Equations ◽  
Prevailing Wind Direction

The effect of wind distribution on the architectural domain of the Bahrain Trade Centre was numerically analysed using computational fluid dynamics (CFD). Using the numerical data, the power generation potential of the building-integrated wind turbines was determined in response to the prevailing wind direction. The three-dimensional Reynolds-averaged Navier-Stokes (RANS) equations along with the momentum and continuity equations were solved for obtaining the velocity and pressure field. Simulating a reference wind speed of 6 m/s, the findings from the study quantified an estimate power generation of 6.4 kW indicating a capacity factor of 2.9% for the benchmark model. At the windward side of the building, it was observed that the layers of turbulence intensified in inverse proportion to the height of the building with an average value of 0.45 J/kg. The air velocity was found to gradually increase in direct proportion to the elevation with the turbine located at higher altitude receiving maximum exposure to incoming wind. This work highlighted the potential of using advanced computational fluid dynamics in order to factor wind into the design of any architectural environment.

SEISMIC RESPONSE OF POWER TRANSMISSION TOWER-LINE SYSTEM UNDER MULTI-COMPONENT MULTI-SUPPORT EXCITATIONS

2012 ◽  
Vol 06 (04) ◽  
pp. 1250025 ◽  
Author(s):  
TIAN LI ◽  
LI HONGNAN ◽  
LIU GUOHUAN
Keyword(s):  
Seismic Waves ◽  
Power Transmission ◽  
Incident Angle ◽  
Ground Motions ◽  
Three Dimensional ◽  
Transmission Tower ◽  
Line System ◽  
Time Stepping ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The effect of multi-component multi-support excitations on the response of power transmission tower-line system is analyzed in this paper, using three-dimensional finite element time-stepping analysis of a transmission tower-line system based on an actual project. Multi-component multi-support earthquake input waves are generated based on the Code for Design of Seismic of Electrical Installations. Geometric non-linearity was considered in the analysis. An extensive parametric study was conducted to investigate the behavior of the transmission tower-line system under multi-component multi-support seismic excitations. The parameters include single-component multi-support ground motions, multi-component multi-support ground motions, the correlations among the three-component of multi-component multi-support ground motions, the spatial correlation of multi-component multi-support ground motions, the incident angle of multi-component multi-support seismic waves, the ratio of the peak values of the three-component of multi-component multi-support ground motions, and site condition with apparent wave velocity of multi-component multi-support ground motions.

Numerical Simulation of Indoor Thermal Environment of a Double-Skin Facade Office with Different Shutter Angles

2014 ◽  
Vol 694 ◽  
pp. 256-259
Author(s):  
Xin Zhan ◽  
Hua Yang ◽  
Feng Yun Jin
Keyword(s):  
Heat Transfer ◽  
Thermal Environment ◽  
Ventilation Rate ◽  
Air Distribution ◽  
Indoor Thermal Environment ◽  
Double Skin ◽  
Computational Fluid Dynamics Cfd ◽  
Heat Transfer Simulation ◽  
Shading Devices ◽  
Rng Turbulence Model

Airflow and heat transfer simulation was conducted for a double-skin façade (DSF) system equipped with shading devices in the cavity, using computational fluid dynamics (CFD) with RNG turbulence model and PISO algorithm, for five conditions of slat angles (θ=0°, 30°, 45°, 60°, 90°). The present study indicates that the presence of shading devices influences the temperatures, the ventilation rate and the air distribution in the DSF system. Besides, the different angles will make different influences.

Mechanism and Flow Control on the Mismatching of Impeller and Vaned Diffuser Caused by Inlet Prewhirl for Centrifugal Compressors

2016 ◽  
Author(s):  
Qiangqiang Huang ◽  
Xinqian Zheng ◽  
Aolin Wang
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Vaned Diffuser ◽  
Inlet Distortion ◽  
Computational Fluid Dynamics Cfd ◽  
Stagger Angle ◽  
Good Agreement ◽  
Matching Relation

Air often flows into compressors with inlet prewhirl, because it will obtain a circumferential component of velocity via inlet distortion or swirl generators such as inlet guide vanes. A lot of research has shown that inlet prewhirl does influence the characteristics of components, but the change of the matching relation between the components caused by inlet prewhirl is still unclear. This paper investigates the influence of inlet prewhirl on the matching of the impeller and the diffuser and proposes a flow control method to cure mismatching. The approach combines steady three-dimensional Reynolds-averaged Navier-Stokes (RANS) simulations with theoretical analysis and modeling. The result shows that a compressor whose impeller and diffuser match well at zero prewhirl will go to mismatching at non-zero prewhirl. The diffuser throat gets too large to match the impeller at positive prewhirl and gets too small for matching at negative prewhirl. The choking mass flow of the impeller is more sensitive to inlet prewhirl than that of the diffuser, which is the main reason for the mismatching. To cure the mismatching via adjusting the diffuser vanes stagger angle, a one-dimensional method based on incidence matching has been proposed to yield a control schedule for adjusting the diffuser. The optimal stagger angle predicted by analytical method has good agreement with that predicted by computational fluid dynamics (CFD). The compressor is able to operate efficiently in a much broader flow range with the control schedule. The flow range, where the efficiency is above 80%, of the datum compressor and the compressor only employing inlet prewhirl and no control are just 25.3% and 31.8%, respectively. For the compressor following the control schedule, the flow range is improved up to 46.5%. This paper also provides the perspective of components matching to think about inlet distortion.

scholarly journals Three-Dimensional Navier–Stokes Analysis and Redesign of an Imbedded Bellmouth Nozzle in a Turbine Cascade Inlet Section

1996 ◽  
Vol 118 (3) ◽  
pp. 529-535 ◽  
Author(s):  
P. W. Giel ◽  
J. R. Sirbaugh ◽  
I. Lopez ◽  
G. J. Van Fossen
Keyword(s):  
Three Dimensional ◽  
Navier Stokes ◽  
Experimental Measurements ◽  
Inlet Section ◽  
Turbine Cascade ◽  
Blade Cascade ◽  
Inlet Geometry ◽  
Computational Fluid Dynamics Cfd ◽  
Transonic Turbine ◽  
Flow Nonuniformity

Experimental measurements in the inlet of a transonic turbine blade cascade showed unacceptable pitchwise flow nonuniformity. A three-dimensional, Navier–Stokes computational fluid dynamics (CFD) analysis of the imbedded bellmouth inlet in the facility was performed to identify and eliminate the source of the flow nonuniformity. The blockage and acceleration effects of the blades were accounted for by specifying a periodic static pressure exit condition interpolated from a separate three-dimensional Navier–Stokes CFD solution of flow around a single blade in an infinite cascade. Calculations of the original inlet geometry showed total pressure loss regions consistent in strength and location to experimental measurements. The results indicate that the distortions were caused by a pair of streamwise vortices that originated as a result of the interaction of the flow with the imbedded bellmouth. Computations were performed for an inlet geometry that eliminated the imbedded bellmouth by bridging the region between it and the upstream wall. This analysis indicated that eliminating the imbedded bellmouth nozzle also eliminates the pair of vortices, resulting in a flow with much greater pitchwise uniformity. Measurements taken with an installed redesigned inlet verify that the flow nonuniformity has indeed been eliminated.

Sign in / Sign up

Export Citation Format

Share Document