scholarly journals NUMERICAL STUDY OF ACOUSTIC CHARACTERISTICS OF A DTMB 4119 PROPELLER DUE TO TIP RAKE

2019 ◽  
Author(s):  
Danio Joe ◽  
Vijit Misra ◽  
R Vijayakumar
Keyword(s):  
Marine Mammals ◽  
Numerical Study ◽  
Hydrodynamic Performance ◽  
Hydrodynamic Characteristics ◽  
Acoustic Characteristics ◽  
Radiated Noise ◽  
Propeller Noise ◽  
Disk Plane ◽  
Propeller Geometry ◽  
The Impact

The impact of increased Underwater Radiated Noise (URN) over the past two decades on marine mammals has resulted in the pressing requirement to reduce it. Shipping contributes immensely to the URN. Propeller noise is a major source of URN. The reduction in Propeller noise can hence significantly help in the reduction of URN. With the sole objective of improving the hydrodynamic performance of propellers ways to prevent cavitation are being developed. However, the reduction of non cavitating noise produced by the propeller would still remain a challenge. The change in the propeller geometry can modify the acoustic characteristics. In this present study, effect of modifying the tip of DTMB4119 propeller on the acoustic and hydrodynamic characteristics is presented. The change in the flow pattern at the tip due to introduction of tip rake is also discussed. The SPL has been calculated by using the two-step Ffowcs William and Hawkings (FW-H) equations from the pressure distribution at various points around the propeller. SPL at various points in the downstream and propeller disk plane are numerically predicted and discussed.

Numerical study of the impact of water injection holes arrangement on cavitation flow control

2019 ◽  
Vol 103 (1) ◽  
pp. 003685041987774 ◽  
Author(s):  
Wei Wang ◽  
Qingdian Zhang ◽  
Tao Tang ◽  
Shengpeng Lu ◽  
Qi Yi ◽  
...  
Keyword(s):  
Flow Field ◽  
Numerical Study ◽  
Water Injection ◽  
Three Dimensional ◽  
Hydrodynamic Performance ◽  
Cavitation Flow ◽  
Suction Surface ◽  
Double Row ◽  
Suppression Effect ◽  
The Impact

A method of water injection to flow field using distributed holes on the suction surface of hydrofoil is presented in this article to control cavitation flow. Modified renormalization group k–ε turbulence model is coupled with full-cavitation model to calculate periodical cavitation patterns and the dynamic characteristics of the NACA66(MOD) hydrofoil. Water injection is found to be highly effective for cavitation suppression. The cavitation suppression effect of distributed regulation of jet holes and porosities along three-dimensional spanwise hydrofoil is also investigated. The appropriate porosities of single row spanwise jet holes and optimal jet position of double row jet holes are revealed for both cavitation suppression and good hydrodynamic performance. Double row jet holes setting in forward trapezoidal arrangement shows great potential for cavitation suppression and hydrodynamic performance. This research provides a method of water injection to flow field to actively control cavitation, which will facilitate development of engineering designs.

scholarly journals Numerical study on the hydrodynamic performance of the semi-spade rudder and propeller

2019 ◽  
Vol 11 (1) ◽  
pp. 168781401882310 ◽  
Author(s):  
Xiao Yang ◽  
Yong Yin ◽  
Jing-Jing Lian
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Turbulence Models ◽  
Suction Side ◽  
Hydrodynamic Performance ◽  
Computational Grids ◽  
Hydrodynamic Characteristics ◽  
Thrust Coefficient ◽  
Ship Maneuverability ◽  
Thrust And Torque

The semi-spade rudder and KP458 propeller of the KVLCC2 (KRISO very large crude carrier) model tanker are adopted by ITTC maneuvering technical committee in the comparative study of ship maneuverability. The incompressible viscous flow around semi-spade rudder and KP458 propeller is investigated using Reynolds-averaged Navier–Stokes equations, the computational grids are generated using ICEM software, and finite volume method is employed to discretize the governing equations. Combined with turbulence model, the hydrodynamic performance of semi-spade rudder is analyzed at different rudder angles, and the result provides a reference for the estimation of the hydrodynamic characteristics of semi-spade rudder. The multi-reference framework method is employed to carry out the numerical simulation of the flow field around the propeller. The thrust and torque of propeller under different turbulence models are calculated in the simulation. The thrust coefficient curve, torque coefficient curve, and efficiency curve are present. The pressure distributions of the pressure side and suction side of propeller blades are studied at different advance coefficient. Based on the study of the hydrodynamic performance of the semi-spade rudder and propeller, the propeller–rudder interaction is simulated and analyzed at different advance coefficient.

A study on the influence of hull wake on model scale cavitation and noise tests for a fast twin screw vessel with inclined shaft

2017 ◽  
Vol 232 (3) ◽  
pp. 307-330
Author(s):  
Giorgio Tani ◽  
Michele Viviani ◽  
Diego Villa ◽  
Marco Ferrando
Keyword(s):  
Scale Effects ◽  
Full Scale ◽  
Ship Wake ◽  
Radiated Noise ◽  
Wake Field ◽  
Model Scale ◽  
Propeller Noise ◽  
Twin Screw ◽  
Long Time ◽  
The Impact

The study of ship underwater radiated noise is nowadays a topic of great and largely recognized importance. This is due to the fact that in the last decades, the problem of the impact of anthropogenic noise on marine life has been addressed with higher emphasis, giving rise to different efforts aimed to the analysis of its effects on different organisms and, in parallel, to means for the reduction of shipping noise. In this context, attention is focused on the propeller noise, which, in cavitating conditions, may represent the most important noise source of the ship. The propeller noise has been studied for long time with different approaches. One of the most effective approaches is represented by model scale testing in cavitation tunnels or similar facilities. Despite having been adopted for several years, radiated noise experiments in model scale are usually affected by significant scale effects and technical issues. One of these aspects is represented by the correct modelling of the propeller inflow; different techniques are adopted, depending on the facility, in order to reproduce a certain target wake. One of the main problems is to define this target wake, which should in principle coincide with the ship wake; as it is well known, it is usually derived from model scale towing tank measurements, with the necessity for the prediction of the full-scale wake field. Starting from the outcomes of a previous work on the influence of different approaches for the prediction of the full-scale wake field for a single screw ship, in this work, attention is focused on the case of a fast twin screw vessel, analysing the different issues which may be connected to this hull form.

scholarly journals Numerical Study of the Hydrodynamic Characteristics Comparison between a Ducted Propeller and a Rim-Driven Thruster

2021 ◽  
Vol 11 (11) ◽  
pp. 4919
Author(s):  
Bao Liu ◽  
Maarten Vanierschot
Keyword(s):  
Numerical Study ◽  
Tip Clearance ◽  
Hydrodynamic Performance ◽  
Navier Stokes ◽  
Hydrodynamic Characteristics ◽  
Significant Discrepancy ◽  
Ducted Propeller ◽  
Wide Range ◽  
Flow Features ◽  
Propeller Blades

The Rim-Driven Thruster (RDT) is an extraordinary innovation in marine propulsion applications. The structure of an RDT resembles a Ducted Propeller (DP), as both contain several propeller blades and a duct shroud. However, unlike the DP, there is no tip clearance in the RDT as the propeller is directly connected to the rim. Instead, a gap clearance exists in the RDT between the rim and the duct. The distinctive difference in structure between the DP and the RDT causes significant discrepancy in the performance and flow features. The present work compares the hydrodynamic performance of a DP and an RDT by means of Computational Fluid Dynamics (CFD). Reynolds-Averaged Navier–Stokes (RANS) equations are solved in combination with an SST k-ω turbulence model. Validation and verification of the CFD model is conducted to ensure the numerical accuracy. Steady-state simulations are carried out for a wide range of advance coefficients with the Moving Reference Frame (MRF) approach. The results show that the gap flow in the RDT plays an important role in affecting the performance. Compared to the DP, the RDT produces less thrust on the propeller and duct, and, because of the existence of the rim, the overall efficiency of the RDT is significantly lower than the one of the ducted propeller.

scholarly journals Numerical Study on the Hydrodynamic Characteristics of Submarine Pipelines under the Impact of Real-World Tsunami-Like Waves

Water ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 221 ◽  
Author(s):  
Enjin Zhao ◽  
Ke Qu ◽  
Lin Mu ◽  
Simon Kraatz ◽  
Bing Shi
Keyword(s):  
Solitary Wave ◽  
Wave Height ◽  
Real World ◽  
Oil And Gas ◽  
High Efficiency ◽  
Numerical Study ◽  
Hydrodynamic Forces ◽  
Hydrodynamic Characteristics ◽  
Tsunami Waves ◽  
The Impact

Submarine pipelines have been extensively used for marine oil and gas extraction due to their high efficiency, safety, and low price. However, submarine pipelines are vulnerable to extreme waves (i.e., tsunami waves). Previous research has often used solitary waves as a basis for studying the impacts of tsunami waves on submarine pipelines, although the hydrodynamic characteristics and wave properties drastically differ from those of real-world tsunami waves. This paper numerically investigates the hydrodynamic characteristics of tsunami waves interacting with submarine pipelines, but instead uses an improved wave model to generate a tsunami-like wave that more closely resembles those encountered in the real-world. The tsunami-like wave generated based on a real-world tsunami wave profile recorded during a 2011 tsunami in Japan has been applied. Given the same wave height, simulation results show that peak hydrodynamic forces of the tsunami-like wave are greater than those of the solitary wave. Meanwhile, the duration of the acting force under the tsunami-like wave is much longer than that of the solitary wave. These findings underline the basic reasons for the destructive power of tsunamis. It is also noted that the hydrodynamic forces of the pipeline under the tsunami-like wave increase with wave height, but will decrease as water depth increases. In addition to the single pipeline, the complicated hydrodynamic characteristics of pipelines in tandem arrangement have been also numerically studied. It is believed that the findings drawn from this paper can enhance our understanding of the induced forces on submarine pipelines under extreme tsunami waves.

scholarly journals A Numerical Study on Heat Transfer in the Channel with Delta Winglet Pair Vortex Generators

2021 ◽  
Vol 39 (4) ◽  
pp. 1305-1312
Author(s):  
Mohammad Mazidi Sharfabadi ◽  
Parham Mobadersani ◽  
Leila Nourpour
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Flow Characteristics ◽  
Vortex Generators ◽  
Hydrodynamic Performance ◽  
Hydrodynamic Characteristics ◽  
Quick Scheme ◽  
Volume Method

In this study, the effect of the vortex generators on the heat transfer and flow characteristics in a rectangular channel is investigated numerically by finite volume method. The governing equations are discretized using QUICK scheme. The numerical results are validated against published experimental data. In this paper, the effects of the winglet aspect ratio and the distance between the vertices of the winglets on the heat transfer and hydrodynamic characteristics of the flow are surveyed. In addition, to achieve the optimum amount of heat transfer, it is important to know the proper arrangement of the triangular winglet pairs as well as their suitable position. Therefore, the appropriate values of the longitudinal and transverse pitch are presented in this paper. The results show that the winglet with the aspect ratio of 1.75 has the best thermal and hydrodynamic performance. Furthermore, the transverse pitch of 1.24 causes 6.5% growth in the average Nusselt number.

scholarly journals Model of thermal buoyancy in cavity-ventilated roof constructions

2021 ◽  
pp. 174425912098418
Author(s):  
Toivo Säwén ◽  
Martina Stockhaus ◽  
Carl-Eric Hagentoft ◽  
Nora Schjøth Bunkholt ◽  
Paula Wahlgren
Keyword(s):  
Analytical Model ◽  
Flow Rate ◽  
Numerical Study ◽  
Air Flow ◽  
Wind Pressure ◽  
Air Flow Rate ◽  
Test Set ◽  
Air Cavity ◽  
Thermal Buoyancy ◽  
The Impact

Timber roof constructions are commonly ventilated through an air cavity beneath the roof sheathing in order to remove heat and moisture from the construction. The driving forces for this ventilation are wind pressure and thermal buoyancy. The wind driven ventilation has been studied extensively, while models for predicting buoyant flow are less developed. In the present study, a novel analytical model is presented to predict the air flow caused by thermal buoyancy in a ventilated roof construction. The model provides means to calculate the cavity Rayleigh number for the roof construction, which is then correlated with the air flow rate. The model predictions are compared to the results of an experimental and a numerical study examining the effect of different cavity designs and inclinations on the air flow rate in a ventilated roof subjected to varying heat loads. Over 80 different test set-ups, the analytical model was found to replicate both experimental and numerical results within an acceptable margin. The effect of an increased total roof height, air cavity height and solar heat load for a given construction is an increased air flow rate through the air cavity. On average, the analytical model predicts a 3% higher air flow rate than found in the numerical study, and a 20% lower air flow rate than found in the experimental study, for comparable test set-ups. The model provided can be used to predict the air flow rate in cavities of varying design, and to quantify the impact of suggested roof design changes. The result can be used as a basis for estimating the moisture safety of a roof construction.

scholarly journals Vibro-Acoustical Sensitivities of Stiffened Aircraft Structures Due to Attached Mass-Spring-Dampers with Uncertain Parameters

Aerospace ◽  
2021 ◽  
Vol 8 (7) ◽  
pp. 174
Author(s):  
Johannes Seidel ◽  
Stephan Lippert ◽  
Otto von Estorff
Keyword(s):  
System Response ◽  
Fuzzy Arithmetic ◽  
Parameter Uncertainties ◽  
Excitation Spectra ◽  
Radiated Noise ◽  
Linking Elements ◽  
Manufacturing Tolerances ◽  
Suitable Framework ◽  
Mass Spring ◽  
The Impact

The slightest manufacturing tolerances and variances of material properties can indeed have a significant impact on structural modes. An unintentional shift of eigenfrequencies towards dominant excitation frequencies may lead to increased vibration amplitudes of the structure resulting in radiated noise, e.g., reducing passenger comfort inside an aircraft’s cabin. This paper focuses on so-called non-structural masses of an aircraft, also known as the secondary structure that are attached to the primary structure via clips, brackets, and shock mounts and constitute a significant part of the overall mass of an aircraft’s structure. Using the example of a simplified fuselage panel, the vibro-acoustical consequences of parameter uncertainties in linking elements are studied. Here, the fuzzy arithmetic provides a suitable framework to describe uncertainties, create combination matrices, and evaluate the simulation results regarding target quantities and the impact of each parameter on the overall system response. To assess the vibrations of the fuzzy structure and by taking into account the excitation spectra of engine noise, modal and frequency response analyses are conducted.

scholarly journals Numerical Simulation of the Impact of the Heat Source Position on Melting of a Nano-Enhanced Phase Change Material

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1425
Author(s):  
Tarek Bouzennada ◽  
Farid Mechighel ◽  
Kaouther Ghachem ◽  
Lioua Kolsi
Keyword(s):  
Heat Transfer ◽  
Phase Change ◽  
Phase Change Material ◽  
Numerical Study ◽  
Melting Rate ◽  
Heat Transfer Fluid ◽  
Commercial Code ◽  
Tube Position ◽  
The Impact ◽  
Change Material

A 2D-symmetric numerical study of a new design of Nano-Enhanced Phase change material (NEPCM)-filled enclosure is presented in this paper. The enclosure is equipped with an inner tube allowing the circulation of the heat transfer fluid (HTF); n-Octadecane is chosen as phase change material (PCM). Comsol-Multiphysics commercial code was used to solve the governing equations. This study has been performed to examine the heat distribution and melting rate under the influence of the inner-tube position and the concentration of the nanoparticles dispersed in the PCM. The inner tube was located at three different vertical positions and the nanoparticle concentration was varied from 0 to 0.06. The results revealed that both heat transfer/melting rates are improved when the inner tube is located at the bottom region of the enclosure and by increasing the concentration of the nanoparticles. The addition of the nanoparticles enhances the heat transfer due to the considerable increase in conductivity. On the other hand, by placing the tube in the bottom area of the enclosure, the liquid PCM gets a wider space, allowing the intensification of the natural convection.

OPTIMAL REINSURANCE FROM THE VIEWPOINTS OF BOTH AN INSURER AND A REINSURER UNDER THE CVAR RISK MEASURE AND VAJDA CONDITION

2021 ◽  
pp. 1-29
Author(s):  
Yanhong Chen
Keyword(s):  
Loss Function ◽  
Value At Risk ◽  
Numerical Study ◽  
Risk Measure ◽  
Convex Combination ◽  
Weighting Factor ◽  
Loss Functions ◽  
Conditional Value At Risk ◽  
Optimal Reinsurance ◽  
The Impact

ABSTRACT In this paper, we study the optimal reinsurance contracts that minimize the convex combination of the Conditional Value-at-Risk (CVaR) of the insurer’s loss and the reinsurer’s loss over the class of ceded loss functions such that the retained loss function is increasing and the ceded loss function satisfies Vajda condition. Among a general class of reinsurance premium principles that satisfy the properties of risk loading and convex order preserving, the optimal solutions are obtained. Our results show that the optimal ceded loss functions are in the form of five interconnected segments for general reinsurance premium principles, and they can be further simplified to four interconnected segments if more properties are added to reinsurance premium principles. Finally, we derive optimal parameters for the expected value premium principle and give a numerical study to analyze the impact of the weighting factor on the optimal reinsurance.

Sign in / Sign up

Export Citation Format

Share Document